A torque product calculator multiplies torque by angular displacement to find rotational work or energy transferred: W = τθ. Enter torque and the angle turned, and the calculator returns the work in joules; the angle must be in radians for this formula.
Formula
The torque product is torque multiplied by angular displacement:
W = τθ
- W is rotational work, in joules (J).
- τ (tau) is torque, in newton-metres (N·m).
- θ (theta) is angular displacement, in radians (rad).
One radian is the angle subtended when an arc has the same length as the radius. To convert degrees to radians, multiply the degree value by π/180. The calculator’s second output converts its entered angle to degrees using θ × 180/π.
Worked Example
Using the calculator’s default inputs, torque is 10 N·m and angular displacement is 1.57079632679 rad.
- Apply the work formula: W = τθ.
- Substitute the values: W = 10 × 1.57079632679 = 15.7079632679 J.
- Rounded to the calculator’s two decimal places, the torque product is 15.71 J.
The angle conversion is 1.57079632679 × 180/π ≈ 90.00 degrees. The example represents a constant 10 N·m torque acting through a quarter turn.
Assumptions
- Torque is constant throughout the angular displacement.
- The entered angle is in radians, and torque is in N·m.
- The result is mechanical work transferred by the torque, not a measure of power or torque alone.
What the Torque Product Means
Torque describes the turning effect of a force about an axis. In SI units it is measured in newton-metres. Work describes energy transferred when a force causes displacement; for rotation, the corresponding displacement is an angle. When torque remains constant and acts in the direction of rotation, multiplying torque by angular displacement gives the work.
A useful unit detail is that 1 N·m is dimensionally equal to 1 joule, since 1 N·m = 1 J. However, torque is conventionally reported in N·m and energy in J to make clear which physical quantity is being described. A torque of 10 N·m is not itself 10 J of work; work depends on how far the object turns.
For example, if a shaft turns through 0.5 rad under a constant torque of 8 N·m, the work is 8 × 0.5 = 4 J. If the same torque acts through 2 rad, the work is 16 J. The greater angular displacement means more energy is transferred, even though the torque is unchanged.
When This Calculator Applies
This calculator is appropriate for a simple constant-torque calculation, such as estimating the work delivered while a shaft or wheel turns through a known angle. It can also help check a textbook exercise or interpret mechanical energy transfer when the torque is specified as constant.
If torque changes as the object turns, one multiplication is not sufficient. The general relationship is an integral:
W = ∫ τ dθ
Here, torque is evaluated over the angular path. If torque depends on angle, use the torque-versus-angle relationship and integrate over the interval, or use a suitable numerical method. For approximately constant torque over small intervals, calculate each interval’s τΔθ and add the contributions.
The sign can matter. If torque acts in the same rotational direction as the displacement, work is positive. If it opposes the rotation, work is negative: energy is being removed from the rotating system or transferred against the motion. This calculator accepts nonnegative torque and angle magnitudes, so interpret its result as the magnitude of work for aligned torque and displacement. For a signed result, apply the appropriate direction sign separately.
Radians, Degrees, and Common Errors
The most common mistake is entering degrees as though they were radians. The formula W = τθ requires radians because radians are the angular unit that makes the rotational work relationship directly consistent. A 90-degree turn is π/2 rad, approximately 1.5708 rad—not 90 rad.
- Convert degrees to radians with: radians = degrees × π/180.
- Convert radians to degrees with: degrees = radians × 180/π.
- Keep torque in N·m if you want the result in joules. If torque is supplied in another unit, convert it first.
- Do not confuse torque with rotational work. Torque alone does not state how much energy was transferred.
- Do not confuse work with power. Power depends on how quickly work is done.
For example, using 90 directly in W = 10 × 90 gives 900, but that treats the angle as 90 radians. For a 90-degree turn, convert first: W = 10 × (π/2) ≈ 15.71 J.
Work, Energy, and Power Compared
Rotational work is energy transferred through angular motion. The calculator reports joules, the SI unit of energy. Power is the rate of energy transfer, measured in watts, where 1 W = 1 J/s. If a known amount of work is completed over a measured time, average power is work divided by time: P = W/t.
For steady rotation, angular speed can also relate torque to power: P = τω, where ω is angular velocity in radians per second. This is not the same calculation as τθ: the latter gives energy over an angular displacement, while the former gives the rate of energy transfer at a particular angular speed. A torque product calculator therefore cannot determine power unless time or angular speed is also known.
Limits and Practical Interpretation
The calculation assumes that the torque value represents the torque acting about the rotation axis and that it remains constant over the stated angle. Real machinery may have friction, changing loads, losses, elastic deformation, or torque that varies through a cycle. The equation describes work associated with the stated torque; it does not automatically account for all energy entering or leaving a complete system.
Be clear about what the torque value represents. A motor’s rated torque, a measured shaft torque, and torque applied at a handle may refer to different locations or operating conditions. For a lever, torque magnitude is often calculated from force times the perpendicular distance to the axis; if force is not perpendicular, the effective torque is τ = rF sin(φ), where φ is the angle between the radius vector and force. This calculator starts with torque already known, so it does not resolve those force-and-geometry details.
For real equipment, use manufacturer or engineering specifications appropriate to the operating conditions, and do not treat a simplified work calculation as a structural or safety rating. Check units, angular direction, and whether the torque is constant before relying on the result.
Frequently Asked Questions
What does torque multiplied by angle calculate?
For constant torque and angular displacement in radians, it calculates rotational work: W = τθ. The result is in joules when torque is in N·m.
Do I use degrees or radians in a torque work calculation?
Use radians. Convert degrees by multiplying by π/180. For example, 90 degrees equals π/2 radians, approximately 1.5708 rad.
Is torque times angle the same as power?
No. Torque times angular displacement gives work or energy transferred. Power is work per unit time; for steady rotation, it can also be calculated as torque times angular velocity.
Can I use this formula when torque changes?
Not as a single torque-times-total-angle calculation unless the torque value is an appropriate average. For changing torque, calculate W = ∫τ dθ, using the torque at each angular position.
Why is torque measured in N·m but work in joules?
The units have the same dimensions, because a joule equals a newton-metre. The different names distinguish torque, a turning effect, from work, an energy transfer.
Related
Formula used
in tau | Torque | N·m | 10 | 0 in theta | Angular displacement | rad | 1.57079632679 | 0 out work | Torque product (work) | J | tau * theta | 2 out deg | Angular displacement | degrees | theta * 180 / pi | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Calculator in Hindi: Meaning, Usage and Examples0.2000 mol/L
- Volume Strength Formula in Terms of Molarity11.20 volumes
- H2O2 Volume Strength to Molarity Calculator0.893 mol/L
- Volume Strength to Molarity: Formula and Calculator0.0409 mol/L
- Molar Volume: Definition, Formula, and Calculator22.414 L/mol
- Molar Volume of a Gas Calculator and Formula22.4140 L/mol