VAV (variable air volume) systems vary the amount of conditioned air delivered to a space as its cooling or heating demand changes; constant-volume systems keep airflow comparatively steady and regulate room conditions mainly by changing the air’s temperature. VAV is often a good fit for buildings with changing or differing room loads, while constant volume can suit simpler, more uniform spaces—but the right choice depends on the building, controls, ventilation needs, and operating conditions.
Formula
This comparison calculator illustrates airflow at a selected VAV operating fraction against a constant-volume system’s design airflow.
- VAV airflow: QVAV = Qdesign × f
- Constant-volume airflow: QCV = Qdesign
Qdesign is the selected design supply airflow in liters per second (L/s). The dimensionless fraction f is the share of design airflow being delivered by the VAV system; 0.5 means 50%. QVAV and QCV are the respective airflow rates in L/s. This is an illustrative airflow comparison, not a sizing calculation or a prediction of energy use. Actual minimum airflow, controls, and system performance must be established from the design and applicable requirements.
Worked Example
Using the calculator defaults, design supply airflow is 500 L/s and the VAV airflow fraction is 0.5.
- VAV airflow: 500 L/s × 0.5 = 250 L/s.
- Constant-volume airflow: 500 L/s.
The calculator therefore returns 250 L/s for the VAV example and 500 L/s for constant volume. The VAV value represents an assumed operating point, not a recommended minimum or a guaranteed real-world flow.
Assumptions
- The selected design airflow is used as the constant-volume comparison point.
- The VAV fraction is a user-selected illustration; real systems have controls and operating limits.
- No energy, heating capacity, cooling capacity, ventilation compliance, or cost is calculated.
How the Two Systems Work
In a typical VAV arrangement, a central air handler conditions air and distributes it through ducts. A terminal unit serving a zone adjusts airflow, often in response to a thermostat or building-control signal. When the zone needs less cooling, the terminal can reduce the supply-air volume. The central fan may also slow down to match system demand, commonly through variable-speed control. Some designs use reheat or other measures when minimum ventilation airflow alone would otherwise overcool a space.
A constant-volume system, as the name suggests, delivers a relatively fixed airflow to its zone or system. Room temperature is managed by changing the supply-air temperature, often at a central unit, or by using another heating or cooling stage. “Constant” does not mean that every component runs at exactly the same rate under every circumstance: equipment cycles, controls, and system design can affect operation. It describes the basic approach to airflow regulation.
Both types can provide heating, cooling, filtration, and outdoor air. Neither label alone tells you whether the system supplies enough fresh air, controls humidity well, or maintains comfort. Those depend on design, commissioning, operation, and maintenance.
Key Differences in Practice
- Airflow: VAV changes zone airflow as demand changes; constant volume aims to maintain a steady airflow.
- Temperature control: VAV commonly uses airflow changes for cooling control, while constant-volume designs commonly adjust supply-air temperature. Real installations can combine strategies.
- Zone variation: VAV can respond to different conditions in separate zones when it has suitable terminal units and controls. A single constant-volume arrangement is less adaptable to uneven zone loads unless it includes additional zoning equipment.
- Fan operation: A VAV system can reduce fan output when demand is lower, potentially saving fan energy. Savings are not automatic; controls, duct pressure settings, schedules, and maintenance matter.
- Complexity: VAV generally requires more zone-level control and balancing. A simpler constant-volume design may have fewer moving control elements, although its overall complexity still depends on the installation.
A common misconception is that VAV always means less outdoor air. The airflow to a zone can fall, but ventilation requirements still apply. Designers must ensure that the system’s minimum airflow and outdoor-air strategy meet the relevant code and occupancy needs. A low-flow setting should never be chosen just to reduce fan energy without checking ventilation and equipment constraints.
How to Choose
Start with the building’s use and load pattern, not with a blanket claim that one approach is more efficient. An office with rooms that fill at different times, changing sunlight, and varied equipment loads may benefit from VAV zoning. A small space with a steady load and straightforward operating schedule might be served adequately by a constant-volume arrangement. A design professional can compare both against the actual floor plan, climate, occupancy, and energy goals.
- Ask how much zones differ. More variation in occupancy and heat gains can make individual airflow control useful.
- Check ventilation and indoor-air requirements. Confirm minimum outdoor-air delivery under both full-load and reduced-load conditions.
- Consider heating and humidity. Low airflow, reheat, cold supply air, and latent loads can affect comfort and control strategy.
- Include controls and maintenance. A theoretically efficient design can underperform if sensors, dampers, fan controls, or schedules are poorly set or maintained.
- Compare life-cycle costs. Include installation, controls, fan and conditioning energy, service, and expected operating hours—not just initial equipment price.
Common Problems and Limits
VAV complaints often include rooms that are too warm or cold, noisy airflow, or insufficient ventilation. Causes can include a miscalibrated thermostat, a stuck or incorrectly adjusted damper, poor air balancing, an unsuitable minimum-flow setting, or a central fan pressure setpoint that is too high or too low. A room’s problem may also come from changing occupancy or loads rather than a failed component.
Constant-volume systems can waste energy when they keep moving a large amount of air despite low demand, especially if the air must be cooled and then reheated. They can also have trouble maintaining different temperatures across zones without additional control measures. But it is inaccurate to assume that every constant-volume installation is inefficient or that every VAV system saves energy: system type, equipment efficiency, climate, operating hours, and control quality all affect results.
The calculator above compares only airflow rates. It cannot determine heating or cooling capacity, energy consumption, noise, or code compliance. Those require additional data, such as supply-air temperature, fan performance, duct characteristics, outdoor-air fraction, weather, and zone loads. For a real project, use the building’s design documents and have a qualified HVAC professional assess the system.
Frequently Asked Questions
Is VAV more energy efficient than constant volume?
It can be, particularly when zone demand varies and fan speed and airflow are controlled well. Actual savings depend on the design, controls, operating schedule, climate, and maintenance; the system name alone does not establish efficiency.
Does VAV mean the fan is always changing speed?
No. VAV describes variable airflow to a zone or system. A central fan may use variable-speed control to respond to demand, but the exact fan and terminal-unit arrangement varies by design.
Can a VAV system provide heating?
Yes. A VAV system can be part of a building’s heating strategy, for example through reheat at terminal units or another heating system. The details matter because reduced airflow and added heat must be coordinated for comfort and efficiency.
Which system is better for a small building?
There is no universal answer. A small building with steady loads may not need the extra zoning and controls of VAV, while a small building with distinct rooms and varying schedules may benefit from them. Compare whole-system cost and performance.
Does constant volume mean constant room temperature?
No. It means airflow is intended to remain comparatively steady. Room temperature can still change as loads change, and the system must regulate supply-air temperature or use other controls to maintain comfort.
Related
Formula used
in v | Design supply airflow | L/s | 500 | 0 in f | VAV airflow fraction | - | 0.5 | 0 out qv | VAV supply airflow | L/s | v * f | 2 out qc | Constant-volume supply airflow | L/s | v | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Cubic Meters per Hour to Liters per Second0.2778 L/s