molecalculator

Moles & Molar Mass

Molar Mass of Copper(II) Sulfate (CuSO₄)

Calculator No. 01-7397 · Updated · Formula and assumptions shown below

Molarity 0.0468 mol/L
Concentration in millimolar
46.81 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
249.69 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The molar mass of anhydrous copper(II) sulfate (CuSO₄) is 159.61 g/mol. If you are working with the common hydrated form, copper(II) sulfate pentahydrate (CuSO₄·5H₂O), the molar mass is 249.69 g/mol. This calculator computes the molar mass of either form from the atomic weights of copper, sulfur, oxygen, and hydrogen.

Formula

Molar mass is the mass in grams of one mole of a substance. For a compound, it is the sum of the atomic weights of each element multiplied by its subscript in the chemical formula.

For anhydrous CuSO₄:

M(CuSO₄) = M(Cu) + M(S) + 4 × M(O)

M(CuSO₄) = 63.546 + 32.06 + 4 × 15.999 = 159.61 g/mol

For the pentahydrate CuSO₄·5H₂O:

M(CuSO₄·5H₂O) = M(CuSO₄) + 5 × [2 × M(H) + M(O)]

M(CuSO₄·5H₂O) = 159.61 + 5 × (2 × 1.008 + 15.999) = 159.61 + 5 × 18.015 = 249.69 g/mol

Variables:

  • M(Cu) = 63.546 g/mol (copper atomic weight)
  • M(S) = 32.06 g/mol (sulfur atomic weight)
  • M(O) = 15.999 g/mol (oxygen atomic weight)
  • M(H) = 1.008 g/mol (hydrogen atomic weight)
  • M(CuSO₄) = molar mass of anhydrous copper(II) sulfate (g/mol)
  • M(CuSO₄·5H₂O) = molar mass of the pentahydrate (g/mol)

Worked Example

Using the calculator defaults: you have 2.922 g of CuSO₄·5H₂O (molar mass 249.69 g/mol) and you dissolve it in enough water to make 250 mL of solution. What is the molarity?

Step 1: Convert the volume to liters.

250 mL = 250 / 1000 = 0.250 L

Step 2: Calculate the number of moles of solute.

moles = mass / molar mass = 2.922 g / 249.69 g/mol = 0.01170 mol (rounded to 4 significant figures)

Step 3: Calculate molarity.

molarity = moles / volume (L) = 0.01170 mol / 0.250 L = 0.0468 mol/L

The calculator rounds to 4 decimal places, giving 0.0468 mol/L (46.8 mM).

Assumptions

  • The solute is pure copper(II) sulfate pentahydrate (CuSO₄·5H₂O) with the stated molar mass.
  • The final volume of the solution is exactly 250 mL (not the volume of water added).
  • Dissolution is complete and the solution is homogeneous.
  • Temperature and pressure do not affect molarity calculations (molarity is based on volume, which can change slightly with temperature, but this is negligible for typical lab work).

Why the Hydrate Matters

Copper(II) sulfate is most often purchased as the blue pentahydrate, CuSO₄·5H₂O. The water molecules are part of the crystal structure, so they contribute to the mass you weigh out. If you use the anhydrous molar mass (159.61 g/mol) when you actually have the hydrate, your calculated molarity will be about 36% too high. Conversely, if you use the hydrate mass when you have anhydrous salt, your solution will be too dilute.

To decide which molar mass to use, check the label on the reagent bottle. It will state whether the chemical is anhydrous or pentahydrate. If the label is missing, the bright blue crystalline form is almost certainly the pentahydrate; the anhydrous form is a pale gray or off-white powder.

How to Read the Result

The first output, molarity (mol/L), tells you the concentration of CuSO₄ in the solution. For example, a 0.0468 mol/L solution contains 0.0468 moles of CuSO₄ per liter. The second output, millimolar (mM), is simply the molarity multiplied by 1000 (0.0468 mol/L = 46.8 mM). Many biology and chemistry protocols express concentrations in mM, so this conversion is handy.

Note that when you dissolve CuSO₄·5H₂O, the water of hydration becomes part of the solvent. The molarity of Cu²⁺ and SO₄²⁻ ions in solution is exactly the same as the molarity of the dissolved salt, because each formula unit dissociates into one Cu²⁺ and one SO₄²⁻.

Common Mistakes and How to Avoid Them

  • Forgetting the water of hydration: Using 159.61 g/mol instead of 249.69 g/mol for the pentahydrate is the most frequent error. Always confirm which form you have.
  • Volume vs. solvent: Molarity uses the final total volume of the solution, not the volume of water added. If you add 250 mL of water to 2.922 g of salt, the final volume will be slightly more than 250 mL, making the concentration lower than calculated.
  • Unit conversions: Ensure mass is in grams and volume is in liters. If you enter volume in mL, the calculator divides by 1000 automatically, but if you do manual calculations, remember to convert.
  • Rounding too early: Round only at the final step. Carrying intermediate values to at least 5 significant figures avoids small errors that can accumulate.

Practical Uses of Copper(II) Sulfate Solutions

Copper(II) sulfate solutions are used in many lab and industrial settings:

  • In qualitative analysis to test for the presence of reducing sugars (Benedict’s test) or proteins (Biuret test).
  • As a source of copper ions in electroplating and electrolysis experiments.
  • As a fungicide in agriculture, though that use is less common in research labs.
  • In the preparation of other copper compounds, such as copper hydroxide or copper carbonate.
  • As a calibration standard for copper analysis by atomic absorption spectroscopy or colorimetry.

For any of these applications, knowing the exact molar mass is the first step to preparing a solution of the required concentration.

Frequently Asked Questions

What is the molar mass of CuSO₄ without water?
The molar mass of anhydrous copper(II) sulfate (CuSO₄) is 159.61 g/mol. This is the sum of 63.546 (Cu), 32.06 (S), and 4 × 15.999 (O).

What is the molar mass of CuSO₄·5H₂O?
The molar mass of copper(II) sulfate pentahydrate is 249.69 g/mol. It is the anhydrous mass (159.61 g/mol) plus five water molecules (5 × 18.015 g/mol = 90.075 g/mol).

Why is the hydrated form blue and the anhydrous form white?
The blue color of the pentahydrate comes from the water molecules coordinated to the copper(II) ion in the crystal lattice. When the water is removed by heating, the anhydrous salt loses that coordination and appears as a pale gray or off-white powder. This color change is often used as a test for water.

How do I convert grams of CuSO₄·5H₂O to moles?
Divide the mass in grams by the molar mass (249.69 g/mol). For example, 2.922 g ÷ 249.69 g/mol = 0.01170 mol. The calculator does this for you when you enter the mass and molar mass.

Does the molar mass change with temperature?
No, molar mass is an intrinsic property of the substance and does not change with temperature. However, the volume of a solution can expand slightly with temperature, so molarity (mol/L) can change slightly. For most lab work, this effect is negligible.

Can I use this calculator for other hydrates?
Yes, you can use the same calculator for any solute by entering its molar mass. For hydrates, just use the molar mass that includes the water of hydration (e.g., 249.69 g/mol for CuSO₄·5H₂O). The calculator does not care what the chemical is; it simply divides mass by molar mass and volume.

Follow your lab method, the safety data sheet (SDS) and your supervisor when preparing copper(II) sulfate solutions. Copper(II) sulfate is harmful if swallowed and can irritate skin and eyes; wear gloves and goggles.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 249.69 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →