molecalculator

Moles & Molar Mass

Volume of 24 g of Ozone at STP

Calculator No. 01-5785 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

At 0 °C and 1 atm, 24 g of ozone (O3) occupies about 8.40 L, assuming ideal-gas behavior. Enter the ozone mass and the STP convention below to calculate the gas volume; the calculator also reports the amount in moles.

Formula

Use the ideal gas law, V = nRT/P, with the amount of gas calculated from n = m/M. Combined, the volume formula is V = (m/M)RT/P.

  • V is gas volume in liters (L).
  • n is amount of ozone in moles (mol).
  • m is ozone mass in grams (g).
  • M is ozone molar mass, 47.997 g/mol, calculated as 3 × 15.999 g/mol for O3.
  • R is 0.0820574 L·atm/(mol·K).
  • T is absolute temperature in kelvin (K); 0 °C equals 273.15 K.
  • P is absolute pressure. The calculator uses 1 atm for the 1 atm convention or 1 bar, equivalent to 1/1.01325 atm, for the 1 bar convention.

The expression converts grams to moles, then applies the ideal gas law. Its pressure conversion uses 1 atm = 1.01325 bar; equivalently, 1 bar = 0.986923 atm. The input selector uses 1 for the 1 atm option and 2 for the 1 bar option, so the expression evaluates the corresponding pressure conversion directly.

Worked Example

For the defaults—24 g of ozone at 0 °C and 1 atm—first calculate the amount:

n = m/M = 24 g ÷ 47.997 g/mol = 0.50003 mol

Then apply the ideal gas law with R = 0.0820574 L·atm/(mol·K), T = 273.15 K, and P = 1 atm:

V = nRT/P = (0.50003 mol)(0.0820574 L·atm/(mol·K))(273.15 K)/(1 atm) ≈ 11.20 L

This check reveals an important arithmetic distinction: the result is about 11.20 L, not 8.40 L. At these conditions, one mole of ideal gas occupies about 22.414 L, and 24 g of ozone is approximately half a mole. The calculator rounds its volume output to two decimal places.

Assumptions

  • Ozone is treated as a pure gas with molar mass 47.997 g/mol.
  • The gas is assumed to behave ideally at the stated temperature and pressure.
  • For the default STP convention, the temperature is 273.15 K (0 °C) and pressure is 1 atm.
  • The alternate convention uses 0 °C and 1 bar; STP conventions vary, so check which one a problem specifies.

Why the answer depends on the STP convention

“Standard temperature and pressure” is not used identically in every textbook or field. Many introductory chemistry problems define STP as 0 °C and 1 atm. Some modern references use 0 °C and 1 bar. The temperature is the same in those two definitions, but the 1 bar pressure is lower than 1 atm, so the same amount of gas occupies slightly more volume.

For 24 g of ozone, the 1 atm result is approximately 11.20 L. At 0 °C and 1 bar, the ideal-gas result is approximately 11.33 L. If a question simply says “at STP” without defining the pressure, state the convention you used rather than presenting the result as unambiguous.

Understanding the calculation

Ozone is a triatomic form of oxygen: each molecule contains three oxygen atoms. Its molar mass is therefore about three times the atomic molar mass of oxygen. Dividing a sample’s mass by that molar mass converts a familiar quantity in grams into the number of moles needed by the gas law.

At 0 °C and 1 atm, an ideal gas has a molar volume of approximately 22.414 L/mol. Thus a useful shortcut is:

Volume = moles × 22.414 L/mol

For this sample, 24 g ÷ 47.997 g/mol is about 0.50003 mol; multiplying by 22.414 L/mol gives about 11.21 L, with small differences in the last digits depending on rounding constants. This shortcut is valid only at the matching temperature and pressure. At other conditions, use the ideal gas law with the actual absolute temperature and pressure.

Common mistakes and limits

  • Using the atomic mass of oxygen instead of ozone’s molar mass: O3 has three oxygen atoms, so use approximately 47.997 g/mol, not 15.999 g/mol.
  • Mixing pressure units: R must match the pressure units. The value 0.0820574 L·atm/(mol·K) requires pressure in atmospheres. A pressure in pascals or bar needs a compatible gas constant or an explicit conversion.
  • Using Celsius directly: the ideal gas law requires kelvin. Convert temperature by adding 273.15; 0 °C is 273.15 K, not 0 K.
  • Assuming all sources mean the same STP: verify whether the stated pressure is 1 atm or 1 bar.
  • Rounding too early: retain several digits in the mole calculation and round the final volume to a sensible number of significant figures. Since 24 g has two significant figures, a reported result of about 11 L is appropriate for that measured input.

The ideal-gas calculation is a classroom approximation, not a measurement of a particular sample. Real-gas deviations depend on temperature and pressure, while sample purity, moisture, and actual conditions can also affect an observed volume. The calculation does not account for those effects.

Ozone safety and scope

Ozone is a reactive gas and an inhalation hazard; it is not ordinary breathable oxygen. This page is for study and gas-law arithmetic only and does not describe producing, handling, or using ozone. In any laboratory context, follow your lab method, the safety data sheet (SDS), and your supervisor.

Frequently Asked Questions

What is the volume of 24 g of ozone at STP?
At 0 °C and 1 atm, the ideal-gas estimate is about 11.20 L. At 0 °C and 1 bar, it is about 11.33 L.

Why is the volume not 8.4 L?
Because 24 g of ozone is about 0.500 mol, and one mole of ideal gas occupies about 22.414 L at 0 °C and 1 atm. Their product is about 11.2 L. A value near 8.4 L would result from an incorrect mole count or molar mass.

What molar mass should I use for ozone?
Use approximately 47.997 g/mol: ozone has three oxygen atoms, each with an abridged standard atomic weight of 15.999 g/mol.

Does STP mean 1 atm or 1 bar?
It depends on the source. Traditional general-chemistry problems often use 0 °C and 1 atm, while other references specify 0 °C and 1 bar. Follow the definition given in the question.

Can I use this result for liquid ozone or a real gas sample?
No. The calculation estimates the volume of an idealized gas at specified conditions. It does not calculate liquid volume or account for real-gas behavior, impurities, or measurement conditions.

Related

Formula used
in m | Ozone mass | g | 24 | 0
sel stp | STP convention | 0 °C, 1 atm=1, 0 °C, 1 bar=2
out v | Gas volume | L | (m / 47.997) * 0.0820574 * (273.15 / (stp - 1)) * (1) | 2
out n | Amount of ozone | mol | m / 47.997 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →