molecalculator

Moles & Molar Mass

Wheel Diameter RPM Speed Calculator

Calculator No. 01-7381 · Updated · Formula and assumptions shown below

Linear speed 31.42 m/s
Speed in km/h
113.10 km/h
= Linear speed × 3.6
Speed in mph
70.28 mph
= Linear speed × 2.236936
Wheel diameter
0.6 m
Set in the form below
You enter
Wheel diameter (m), Rotational speed (RPM)
You get
Linear speed (m/s), Speed in km/h (km/h), Speed in mph (mph)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator determines the linear speed of a wheel (or any rotating object) from its diameter and rotational speed (RPM). You enter the wheel diameter and the RPM, and it returns the speed in your choice of units (m/s, km/h, mph, ft/s). The core relationship is simple: speed = circumference × rotations per second.

Formula

The linear speed \(v\) of a point on the rim of a wheel is the product of the wheel’s circumference and its rotation frequency. The circumference \(C\) of a circle is \(\pi\) times the diameter \(d\):

\(C = \pi \times d\)

If the wheel spins at \(N\) revolutions per minute (RPM), each revolution covers a distance equal to \(C\). To convert RPM to revolutions per second, divide by 60. Therefore:

\(v = \frac{\pi \times d \times N}{60}\)

Where:

  • \(v\) = linear speed at the wheel rim (m/s)
  • \(d\) = wheel diameter (m)
  • \(N\) = rotational speed (RPM)
  • \(\pi \approx 3.14159\)

To get km/h, multiply \(v\) (in m/s) by 3.6. To get mph, multiply by 2.236936 (since 1 m/s = 2.236936 mph).

Worked Example

Using the default values: a wheel diameter of 0.6 m (about the size of a car tire) and a rotational speed of 1000 RPM.

  1. Circumference: \(C = \pi \times 0.6 = 1.88496\) m
  2. Revolutions per second: \(1000 / 60 = 16.6667\) rev/s
  3. Linear speed: \(v = 1.88496 \times 16.6667 = 31.416\) m/s
  4. In km/h: \(31.416 \times 3.6 = 113.10\) km/h
  5. In mph: \(31.416 \times 2.236936 = 70.28\) mph

The calculator gives the same result: 31.42 m/s, 113.10 km/h, 70.28 mph.

Assumptions

  • The wheel is a perfect circle and rolls without slipping.
  • The diameter is measured at the outer edge of the tire/rim (the actual contact surface).
  • No deformation of the tire under load (a real tire flattens slightly, reducing effective diameter by a few percent).
  • Rotational speed is constant.

How to Use This Calculator

Enter the wheel diameter in meters (or convert from mm, cm, inches first – see common mistakes below) and the RPM. The first output is the speed in meters per second, the standard SI unit. The second and third outputs give the same speed in km/h and mph, which are more intuitive for vehicle speeds. For example, a bicycle wheel with a diameter of 0.7 m spinning at 120 RPM gives a speed of \(\pi \times 0.7 \times 120/60 = 4.40\) m/s, or about 15.8 km/h – a typical cycling pace.

This calculation is used in many fields: robotics (wheeled robots), conveyor belts, vehicle speedometers, and even cutting speeds in machining. In machining, the “cutting speed” is the linear speed of the workpiece or tool surface, and it is calculated from the spindle RPM and the diameter of the part or cutter. For a lathe, if you know the desired surface speed (e.g., 100 m/min for mild steel), you can rearrange the formula to find the required RPM: \(N = \frac{v \times 60}{\pi \times d}\).

Common Mistakes and How to Avoid Them

  • Unit mix-ups: The most common error is entering a diameter in centimeters or inches without converting to meters. Always convert: 1 cm = 0.01 m, 1 inch = 0.0254 m. If you enter 0.6 cm instead of 0.6 m, the result will be 100 times too small.
  • Using radius instead of diameter: The formula uses diameter. If you have the radius, double it first. Using the radius directly gives a speed that is half the correct value.
  • Confusing RPM with revolutions per second: RPM is per minute; you must divide by 60. A common mistake is to multiply by 60 instead, which would give a speed 3600 times too large.
  • Ignoring tire deformation: For a car, the effective rolling radius is slightly less than the unloaded radius because the tire flattens at the contact patch. This can cause a speedometer to read a few km/h high. The calculator uses the nominal diameter, which is accurate for most planning purposes.

Practical Examples

  • Car speed: A car tire has a diameter of about 0.65 m. At 3000 RPM (engine speed, not wheel speed – but if you consider the wheel spinning at that RPM), the speed would be \(\pi \times 0.65 \times 3000/60 = 102.1\) m/s = 367.6 km/h – unrealistically fast because the wheel RPM is much lower than the engine RPM due to the gearbox. For a real car, you need the wheel RPM, which is engine RPM divided by the gear ratio.
  • Conveyor belt: A conveyor drum of diameter 0.2 m rotating at 50 RPM moves the belt at \(\pi \times 0.2 \times 50/60 = 0.524\) m/s, or about 31.4 m/min – a typical slow conveyor speed.
  • Bicycle: A 700c wheel has a diameter of about 0.67 m. At a cadence of 90 RPM with a gear ratio that makes the wheel spin at 300 RPM (a high gear), the speed is \(\pi \times 0.67 \times 300/60 = 10.5\) m/s = 37.9 km/h – a fast sprint.

Limitations of the Formula

The formula assumes a rigid wheel and no slip. In reality, tires deform, and the effective rolling radius changes with load and inflation pressure. For a car, the difference between the unloaded radius and the loaded radius can be 2-3%, which translates to a similar error in speed. Also, the formula gives the speed of the wheel’s outer surface; if you want the speed of the vehicle, you must use the wheel’s rolling radius, which is the distance from the center to the ground when the wheel is loaded. For a train wheel on a rail, the contact is nearly a point, so the nominal diameter is accurate.

Another limitation: the formula assumes the wheel is rolling without slipping. If the wheel is slipping (e.g., on ice or during hard acceleration), the vehicle speed will be lower than the wheel surface speed. Conversely, if the wheel is locked and sliding, the vehicle speed is not related to the wheel RPM at all.

Frequently Asked Questions

How do I convert wheel diameter from inches to meters?

Multiply the inch value by 0.0254. For example, a 26-inch bicycle wheel is 26 × 0.0254 = 0.6604 m. Always do this conversion before entering the diameter into the calculator.

What is the difference between wheel speed and vehicle speed?

Wheel speed is the linear speed of the tire’s outer surface. Vehicle speed is the speed of the vehicle’s chassis. When there is no slip, they are equal. But during acceleration or braking, the wheel can spin faster or slower than the vehicle’s actual ground speed.

Can I use this for a gear or pulley?

Yes. The formula applies to any rotating object. For a gear, the “diameter” is the pitch diameter (the effective diameter for meshing). For a pulley, use the outer diameter of the belt contact surface. The linear speed is the belt speed.

How do I find RPM from a desired speed?

Rearrange the formula: \(N = \frac{v \times 60}{\pi \times d}\). For example, to achieve a speed of 20 m/s with a 0.5 m diameter wheel, the RPM is \(20 \times 60 / (\pi \times 0.5) = 763.94\) RPM.

Why does my car’s speedometer show a different speed than the GPS?

Speedometers are calibrated for the nominal tire diameter, but tires wear down (reducing diameter) and can be under-inflated (reducing effective radius). Also, speedometers are often intentionally optimistic by a few percent. GPS measures actual ground speed, so differences of 2-5% are common.

Does the formula work for non-circular wheels?

No. The formula is for circular wheels. For a non-circular shape, the instantaneous speed varies with the angle, and the average speed depends on the shape’s perimeter, not a simple diameter. In practice, almost all wheels are circular.

Related

Formula used
in d | Wheel diameter | m | 0.6 | 0.001
in rpm | Rotational speed | RPM | 1000 | 0
out v | Linear speed | m/s | pi * d * rpm / 60 | 2
out kmh | Speed in km/h | km/h | v * 3.6 | 2
out mph | Speed in mph | mph | v * 2.236936 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →