For a zero-order reaction, the rate constant k has units of concentration per time, commonly mol L−1 s−1 (M/s). This calculator finds k from an initial concentration, a later concentration, and the elapsed time; it also reports the reaction rate in the same concentration-per-time units.
Formula
For the integrated zero-order rate law, concentration falls linearly with time:
[A]t = [A]0 − kt, so k = ([A]0 − [A]t) / t.
- [A]0 is the initial reactant concentration, in mol/L.
- [A]t is its concentration after elapsed time t, also in mol/L.
- t is elapsed time, here in seconds.
- k is the zero-order rate constant, in mol/(L·s) for these selected units.
The rate of disappearance is written as −d[A]/dt = k, so the positive numerical value of k is also the zero-order disappearance rate. The minus sign in d[A]/dt indicates that reactant concentration decreases. The calculator uses the average change over the interval; for an ideal zero-order reaction with constant rate, that average equals the instantaneous rate throughout the interval.
Worked Example
Using the calculator defaults, the concentration changes from 0.100 mol/L to 0.040 mol/L over 120 s.
- Find the concentration decrease: 0.100 mol/L − 0.040 mol/L = 0.060 mol/L.
- Divide by elapsed time: k = 0.060 mol/L ÷ 120 s = 0.0005 mol/(L·s).
- To the four decimal places displayed, k = 0.0005 mol/(L·s). The reported average rate of disappearance is also 0.0005 mol/(L·s).
In scientific notation, the unrounded value is 5.0000 × 10−4 mol/(L·s). The displayed result is rounded to four decimal places, as specified in the calculator block.
Assumptions
- The concentration measurements refer to the same reactant and use the same concentration unit.
- Time is positive for a meaningful interval, and the later concentration is no greater than the initial concentration.
- The reaction follows zero-order behavior over the interval: its rate is independent of reactant concentration under the conditions being considered.
- The calculation treats the measured concentration change as due to the reaction, not sampling loss, dilution, evaporation, or measurement error.
Why Zero-Order Units Differ
Reaction order determines the units of a rate constant because it determines how concentration appears in the rate law. A rate always has concentration-per-time units. For a zero-order process, the rate law is rate = k, so k itself must have the units of rate: concentration divided by time.
With concentration in mol/L and time in seconds, the unit is mol L−1 s−1, equivalently M s−1. If time is recorded in minutes, the matching unit is mol L−1 min−1. The numerical value changes with the time unit: 0.0005 mol L−1 s−1 equals 0.030 mol L−1 min−1, because one minute is 60 seconds.
Other concentration units are valid if they are used consistently. For example, if concentration is measured in mmol/L and time in minutes, k is in mmol L−1 min−1. Do not report a number without its units: a bare value for k is ambiguous.
How to Recognize Zero-Order Behavior
“Zero order” means that the observed rate does not depend on the concentration of the reactant in the rate law over the conditions tested. It does not mean that the reaction has no rate, or that concentration remains constant. Instead, concentration decreases at a constant rate while the zero-order model applies.
A useful graphical test is to plot reactant concentration against time. A straight line with a negative slope supports zero-order behavior; the slope is −k. By contrast, a first-order reaction tends to produce a straight line when ln[A] is plotted against time, and a second-order reaction often gives a straight line for 1/[A] against time under the corresponding simple rate-law assumptions. A fitted line and residuals are more informative than calculating k from only two points, since two points always define a line.
Zero-order kinetics can occur when a process is limited by a factor that is effectively constant, such as a saturated catalyst or a fixed-intensity light source in a suitable photochemical system. These are context-dependent examples, not proof that any particular reaction is zero order. Order is established from experimental behavior or a justified mechanism, not simply from the balanced chemical equation.
Using and Interpreting the Calculator
Enter concentrations in mol/L and elapsed time in seconds. The inputs must represent the initial and later measurements for the same reaction interval. The calculator subtracts the later concentration from the initial concentration and divides by time.
- If the later concentration is lower, k is positive, as expected for reactant disappearance.
- If both concentrations are equal, the calculated interval rate is zero; that may reflect a plateau, limited precision, or an interval too short to resolve a change.
- If the later concentration is higher, the supplied values do not fit this calculator’s assumed decrease. Check the measurement order, units, or whether the measured substance is actually being formed.
- If time is zero, the rate cannot be calculated from a concentration difference; a rate requires a nonzero time interval.
The calculator estimates an interval rate, not the uncertainty of that rate. Measurement uncertainty can matter greatly when the concentration difference is small. For better evidence, use several time points, replicate measurements where appropriate, and assess whether a linear concentration-versus-time fit is reasonable.
Common Unit Mistakes and Limits
A frequent mistake is to use concentration in mmol/L but label the result mol/(L·s), or to combine a time in minutes with a result labeled per second. Convert first or clearly retain the units produced by the arithmetic. For example, 1 mmol/L = 0.001 mol/L and 1 min = 60 s.
Another misconception is that zero-order units are always written as M/s. That is common shorthand, but the unit depends on the chosen concentration and time scales. Also, the dimensions of k alone do not prove the reaction order; the order comes from how rate changes with concentration or from a validated kinetic model.
The simple integrated equation applies only while zero-order behavior is a suitable approximation. Real systems can change order as reactants are depleted, catalysts deactivate, light intensity changes, or conditions shift. A straight-line model can also conceal noisy or curved data over a short range. Do not extrapolate the line beyond the measured range without a sound reason: the equation predicts [A] = 0 at t = [A]0/k, but the reaction may stop following zero-order behavior before that point.
Frequently Asked Questions
What are the units of a zero-order rate constant?
They are concentration per time, such as mol L−1 s−1 or M/s when concentration is mol/L and time is seconds.
Why does zero-order k have the same units as reaction rate?
The zero-order rate law is rate = k: there is no concentration term multiplying k, so k must carry the full concentration-per-time dimensions of the rate.
Is M/s the only correct unit for k?
No. It is correct when concentration is in mol/L and time is in seconds. Units such as mol L−1 min−1 are also valid when time is measured in minutes.
Does zero order mean the concentration does not change?
No. It means the rate is independent of reactant concentration under the conditions described by the model. The concentration can still decrease linearly with time.
How can I tell whether a reaction is zero order?
Check whether concentration-versus-time data are reasonably linear over the interval, ideally using multiple measurements and a fit. A single calculated rate does not establish the reaction order.
Related
Formula used
in c0 | Initial concentration | mol/L | 0.100 | 0 in ct | Concentration at time t | mol/L | 0.040 | 0 in t | Elapsed time | s | 120 | 0 out k | Zero-order rate constant k | mol/(L·s) | (c0 - ct) / t | 4 out r | Average rate of disappearance | mol/(L·s) | k | 4
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Cell Culture Doubling Time Equation and Calculator24.00 h
- Cell Culture Seeding Density Calculator and Formula4,000.00 cells/cm^2
- Cell Culture Doubling Time Calculator and Formula24.00 h
- CFU From Dilution: Calculate Colony-Forming Units10,000,000 CFU/mL
- Cell Culture Doubling Time Calculator and Formula24.00 h
- Zero Order Release Kinetics Calculator and Explanation5.000 mg/h