molecalculator

Moles & Molar Mass

Liters per Minute to Cubic Meters per Second

Calculator No. 01-6464 · Updated · Formula and assumptions shown below

Flow rate 0.001000 m³/s
Flow rate
1.0000 L/s
= Flow rate ÷ 60
Flow rate
60 L/min
Set in the form below
You enter
Flow rate (L/min)
You get
Flow rate (m³/s), Flow rate (L/s)
Rounding
6 dp · 4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator converts a flow rate from liters per minute (L/min) to cubic meters per second (m³/s). Enter the value in L/min to get the equivalent SI flow rate, using the exact unit-conversion factors.

Formula

To convert liters per minute to cubic meters per second, divide by 1,000 to change liters into cubic meters, then divide by 60 to change minutes into seconds:

Q (m³/s) = q (L/min) ÷ 1,000 ÷ 60 = q ÷ 60,000

  • q is the input flow rate in liters per minute (L/min).
  • Q is the converted flow rate in cubic meters per second (m³/s).
  • The factors 1,000 L per m³ and 60 s per minute are exact unit relationships.

The calculator also shows liters per second as a convenient intermediate-scale result: q (L/s) = q (L/min) ÷ 60. The main answer is always in m³/s.

Worked Example

Using the calculator’s default input of 60 L/min:

  1. Convert liters to cubic meters: 60 L/min ÷ 1,000 = 0.06 m³/min.
  2. Convert minutes to seconds: 0.06 m³/min ÷ 60 = 0.001 m³/s.
  3. In liters per second, 60 L/min ÷ 60 = 1 L/s.

So, 60 L/min = 0.001000 m³/s (to six decimal places), or 1 L/s.

Assumptions

  • The input is a volumetric flow rate expressed in liters per minute.
  • The flow is treated as a rate of volume, with no density or substance-specific conversion needed.
  • The conversion changes units only; it does not estimate flow from pressure, velocity, or equipment specifications.

Why the Conversion Factor Is 60,000

A liter is one-thousandth of a cubic meter: 1 L = 0.001 m³. A minute contains 60 seconds. Therefore, one liter per minute is 0.001 cubic meters spread over 60 seconds:

1 L/min = 0.001 m³ ÷ 60 s = 1/60,000 m³/s ≈ 0.0000166667 m³/s.

That means the shortcut is to divide an L/min value by 60,000. For example, 120 L/min ÷ 60,000 = 0.002 m³/s. To convert in the opposite direction, multiply a value in m³/s by 60,000 to obtain L/min.

The conversion is purely dimensional: it applies to any liquid or gas when the stated quantity is volumetric flow. Temperature, pressure, and fluid identity do not alter the arithmetic. They can, however, affect the actual volume occupied by a gas or the flow a system can deliver, so those conditions may matter when interpreting a measured or specified rate.

How to Use and Read the Result

Enter the numeric flow rate in L/min. The calculator returns m³/s first and L/s second. For example, a displayed answer of 0.0005 m³/s means that 0.0005 cubic meters pass a reference point each second; it does not mean 0.0005 cubic meters per minute.

  • For 1 L/min: 1 ÷ 60,000 = 0.0000166667 m³/s.
  • For 10 L/min: 10 ÷ 60,000 = 0.000166667 m³/s.
  • For 100 L/min: 100 ÷ 60,000 = 0.00166667 m³/s.
  • For 1,000 L/min: 1,000 ÷ 60,000 = 0.0166667 m³/s.

The result can look small because a cubic meter is a large volume: it contains 1,000 liters. A small decimal in m³/s can therefore correspond to a readily understandable flow in L/min. Use the calculator’s L/s output or the original input when a decimal in cubic meters per second is inconvenient to communicate.

Common Unit Mistakes and Limits

The most frequent mistake is converting only one part of the unit. Dividing by 1,000 changes liters to cubic meters but leaves the time basis in minutes; dividing by 60 changes minutes to seconds but leaves volume in liters. Both steps are required for m³/s.

  • Do not divide by 60,000 twice. The complete conversion factor already includes both unit changes.
  • Check the starting unit. L/h, mL/min, and gallons per minute need different conversion factors. Convert to L/min first if using this calculator.
  • Keep the time unit attached. A value in m³/min is not the same as m³/s; there is a factor of 60 between them.
  • Round only at the end. Retain useful digits during intermediate calculations, especially for small rates.

This conversion does not calculate mass flow, such as kg/s. To get mass flow from volumetric flow, a fluid density is also needed, and density can depend on the substance and conditions. Nor does the conversion determine whether a pipe, pump, or process can sustain a particular rate; that requires system-specific information.

Choosing a Useful Unit

m³/s is the SI unit for volumetric flow rate and is often useful in engineering equations and large-scale flow calculations. L/min is familiar for moderate flows, while L/s can be easier to compare with m³/s because 1 m³/s equals 1,000 L/s. Pick units that make the scale easy to read, but preserve the unit whenever you copy a result into another calculation.

For rough mental checks, remember that 60,000 L/min equals 1 m³/s. Thus 6,000 L/min is 0.1 m³/s, and 600 L/min is 0.01 m³/s. These checks can reveal a misplaced factor of 10 or 60,000, but use the full calculation for a reported value.

Frequently Asked Questions

How many cubic meters per second is 1 liter per minute?
1 L/min equals 1/60,000 m³/s, or approximately 0.0000166667 m³/s.

What is the formula for converting L/min to m³/s?
Divide the value in L/min by 60,000. This combines 1,000 liters per cubic meter and 60 seconds per minute.

How do I convert m³/s back to L/min?
Multiply the flow rate in m³/s by 60,000. For example, 0.002 m³/s × 60,000 = 120 L/min.

Is L/min the same as m³/min?
No. A cubic meter contains 1,000 liters, so 1,000 L/min equals 1 m³/min. To express that rate in m³/s, divide the m³/min value by 60.

Does the conversion change for gas or liquid?
The unit conversion does not change. But a gas’s volume can vary with pressure and temperature, so check the conditions attached to the flow-rate measurement or specification when comparing gas flows.

Related

Formula used
in flow | Flow rate | L/min | 60 | 0
out cms | Flow rate | m³/s | flow / 1000 / 60 | 6
out ls | Flow rate | L/s | flow / 60 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →