molecalculator

Moles & Molar Mass

Absorbance vs. Concentration Graph: Formula and Example

Calculator No. 01-5313 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

An absorbance-versus-concentration graph plots measured absorbance on the vertical axis against the known concentration of a light-absorbing substance on the horizontal axis. This calculator uses the Beer–Lambert law to estimate the slope, or molar absorptivity, from absorbance and concentration, and returns the predicted absorbance for a chosen concentration.

Formula

The Beer–Lambert law is A = εlc. Rearranging it gives ε = A/(lc), the calculation used for the first output. The predicted absorbance at a selected concentration is Apredicted = εlc.

  • A is absorbance, a dimensionless ratio commonly reported without a unit.
  • ε is molar absorptivity, in L/(mol·cm) when concentration is in mol/L and path length is in cm.
  • l is the optical path length through the sample, in cm.
  • c is concentration, in mol/L.

The calculator treats one absorbance and concentration pair as a point on a straight-line calibration graph and assumes the line passes through zero. For a full graph, measure several standards and fit a line; the fitted slope is normally more reliable than calculating a slope from one point.

Worked Example

Using the block’s default values: A = 0.500, c = 0.0100 mol/L, and l = 1.00 cm.

  1. Calculate molar absorptivity: ε = A/(c × l) = 0.500/(0.0100 mol/L × 1.00 cm) = 50.0 L/(mol·cm).
  2. Predict absorbance for the same concentration and path length: Apredicted = ε × c × l = 50.0 L/(mol·cm) × 0.0100 mol/L × 1.00 cm = 0.500.

The first result is 50.000 L/(mol·cm), displayed to three decimal places; the predicted absorbance is 0.500.

Assumptions

  • The sample is sufficiently dilute for absorbance to be proportional to concentration over the range being considered.
  • The wavelength, chemical form of the absorbing species, solvent, and measurement conditions are held constant.
  • The entered path length is the actual optical path through the sample; the example uses a 1.00 cm path.
  • The simple prediction assumes a zero-intercept relationship. Real instruments and blanks can produce a nonzero intercept.

What the Graph Shows

Absorbance describes how much light a sample removes from a beam at a specified wavelength. In a common definition, A = log10(I0/I), where I0 is incident light intensity and I is transmitted intensity. Because absorbance is logarithmic in transmission, it is not the same quantity as percent transmittance: A = 1 corresponds to 10% transmittance, while A = 2 corresponds to 1%, assuming the same measurement definition.

For a calibration graph, prepare or obtain standards with known concentrations, measure their absorbance under consistent conditions, and plot each pair. If Beer–Lambert behavior applies, the data lie approximately along a straight line. For the line A = mc + b, the slope m represents εl when concentration units match the chosen convention, and b is the intercept. With concentration in mol/L and path length in cm, m has units L/mol; dividing it by l gives ε in L/(mol·cm).

A graph is more informative than one point because it shows scatter, possible outliers, curvature, and whether the standards cover the concentration of an unknown. Use the calibration line to estimate an unknown’s concentration from its absorbance, usually by rearranging A = mc + b to c = (A − b)/m. The calculator here illustrates the law from one pair; it does not perform regression or uncertainty analysis.

How to Build and Read a Calibration Line

  1. Choose a wavelength at which the analyte absorbs and keep it fixed for standards and unknowns.
  2. Measure a blank containing the relevant solvent and other background components, then use it to correct the sample readings as appropriate for the instrument and method.
  3. Measure several standards spanning the expected unknown concentration. Record concentration, absorbance, and relevant conditions such as path length.
  4. Plot concentration on the x-axis and absorbance on the y-axis, then fit a line over the range that is acceptably linear.
  5. Use the fitted equation to estimate unknown concentrations only within, or cautiously near, the calibrated range.

The slope is not automatically the molar absorptivity: it equals ε times path length only when the concentration is expressed in mol/L and the path length in cm. If concentration is in mmol/L, mg/L, or another unit, the slope’s units and numerical value change. Convert units before comparing slopes or interpreting ε.

Linearity, Limits, and Common Problems

Beer–Lambert proportionality is an approximation with a useful working range, not a guarantee that every sample produces a perfect straight line. At higher concentrations, interactions between absorbing particles and changes in solution properties can cause deviations. Instrument limitations, stray light, broad spectral bands, chemical equilibria, and scattering from particles can also affect measurements. A curved graph is a warning to check the concentration range and measurement conditions rather than forcing a linear fit.

  • Forcing the line through zero: A blank-corrected graph may still have a nonzero intercept. Fit an intercept when justified by the data and method; do not remove it solely to make the equation look simpler.
  • Mixing concentration units: A slope based on mg/L is not numerically interchangeable with one based on mol/L. State units with the equation.
  • Ignoring path length: A different cuvette path length changes the slope. Include l when calculating ε or comparing results.
  • Using readings outside the standards: Extrapolation beyond the calibrated range can be unreliable. Dilute an out-of-range sample according to the validated method, measure it within range, then account for the dilution factor.
  • Rounding too early: Keep unrounded values during calculations and round the reported result to a precision supported by the measurements.

Absorbance has no physical unit, but a reported value still depends on wavelength, blank correction, instrument setup, and sample handling. For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.

Frequently Asked Questions

Is absorbance directly proportional to concentration?
Approximately, when Beer–Lambert conditions hold and wavelength, path length, chemical form, and other relevant conditions are fixed. The relationship may fail outside the method’s linear range.

Which variable goes on each axis?
Put concentration on the x-axis and absorbance on the y-axis for the usual calibration graph. The fitted slope then describes the change in absorbance per concentration unit.

What does the slope of an absorbance-concentration graph mean?
For A = mc + b, the slope m equals εl when concentration is in mol/L and path length is in cm. It is not ε alone unless the path length is 1 cm.

Should an absorbance calibration line pass through zero?
Not necessarily. Blank correction can reduce background offset, but a nonzero intercept may remain. Use an intercept based on the measurements and the validated analytical method.

Can I find an unknown concentration from its absorbance?
Yes, with a suitable calibration equation: c = (A − b)/m. The unknown should be measured under the same conditions and fall within the standards’ reliable range.

Related

Formula used
in a | Absorbance | - | 0.500 | 0
in c | Concentration | mol/L | 0.0100 | 0
in l | Path length | cm | 1.00 | 0
out e | Molar absorptivity | L/(mol·cm) | a / (c * l) | 3
out ap | Predicted absorbance | - | e * c * l | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →