Air density in Wisconsin is not one fixed value: it changes with air temperature, atmospheric pressure, humidity, and elevation. Use the calculator below to estimate the density of moist air in kilograms per cubic metre; enter local pressure, temperature, and relative humidity to see how dense the air is under those conditions.
Formula
The calculator uses the ideal-gas mixture relation for dry air and water vapour. It first estimates saturation vapour pressure, scales it by relative humidity to get the actual water-vapour partial pressure, then calculates the density contributed by each gas:
- Saturation vapour pressure: es = 611.2 × exp(17.67T / (T + 243.5)) pascals, where T is temperature in °C.
- Water-vapour pressure: e = (RH / 100) × es, where RH is relative humidity in percent.
- Moist-air density: ρ = (p − e) / (RdTK) + e / (RvTK).
Here, p is atmospheric pressure in pascals, converted from kPa by multiplying by 1,000; TK = T + 273.15 is absolute temperature in kelvins; Rd = 287.05 J/(kg·K) is the specific gas constant for dry air; and Rv = 461.495 J/(kg·K) is the specific gas constant for water vapour. The second output calculates dry-air density as ρdry = p / (RdTK), treating the full pressure as dry air. This is a comparison, not the moist-air result.
Worked Example
With the default values—101.325 kPa, 20 °C, and 50% relative humidity—the saturation vapour pressure is approximately 2,338.3 Pa:
es = 611.2 × exp(17.67 × 20 / (20 + 243.5)) ≈ 2338.3 Pa
Actual water-vapour pressure is 0.50 × 2338.3 = 1169.2 Pa. Convert the entered pressure: 101.325 × 1,000 = 101325 Pa. Absolute temperature is 20 + 273.15 = 293.15 K. Therefore:
ρ = (101325 − 1169.2) / (287.05 × 293.15) + 1169.2 / (461.495 × 293.15) ≈ 1.199 kg/m³
The dry-air comparison is ρdry = 101325 / (287.05 × 293.15) ≈ 1.204 kg/m³. Moist air is less dense here because water-vapour molecules have a lower average molar mass than the main components of dry air.
Assumptions
- Air and water vapour are treated as ideal gases, and their partial-pressure contributions are added.
- The saturation vapour pressure equation is an approximation suitable for ordinary weather conditions, not extreme temperatures or pressures.
- Pressure entered is the actual local atmospheric pressure, not a weather-station value adjusted to sea level.
- Relative humidity is between 0% and 100%; temperature must be above absolute zero.
Why Wisconsin Air Density Varies
Wisconsin spans modest but meaningful elevation differences. Much of the state is a few hundred metres above sea level, while higher terrain in the west and north can be substantially higher. Atmospheric pressure generally falls as elevation rises, so air at a higher Wisconsin location is usually less dense than air at a lower location when temperature and humidity are otherwise alike. Exact elevation alone is not enough to determine density because weather systems also change pressure.
Temperature has a large everyday effect: warm air expands, and at the same pressure its density is lower than cool air. Humidity matters too. At fixed temperature and total pressure, adding water vapour generally lowers density because water molecules are lighter than the nitrogen and oxygen molecules that dominate dry air. These effects can compete; a hot, humid afternoon can still have denser air than a much higher-elevation location under different pressure conditions.
For a rough comparison, standard-atmosphere sea-level air at 15 °C has a density of about 1.225 kg/m³. That is a reference condition, not a claim about Wisconsin’s current weather or a statewide average. The calculator’s default conditions instead give about 1.199 kg/m³ at 20 °C, sea-level pressure, and 50% humidity. Actual local density requires current pressure, temperature, and humidity observations.
Getting Useful Local Inputs
For the best estimate, use observations from near the place and time you care about. Temperature and relative humidity are commonly reported in weather observations. Pressure needs special care: many forecasts publish pressure reduced to sea level to make weather maps comparable. For air density at your site, use station pressure—the pressure measured at the station’s elevation—or convert a sea-level pressure using a suitable atmospheric model and elevation data.
- Enter pressure in kPa. If a reading is in hPa or millibars, divide by 10 to obtain kPa; for example, 990 hPa is 99.0 kPa.
- Enter temperature in °C. The formula converts it to kelvins internally.
- Enter relative humidity as a percentage from 0 to 100, not as a decimal fraction. For example, enter 50 for 50%.
- Keep the readings reasonably consistent in time and location; mixing a nearby temperature with pressure from another elevation can distort the estimate.
How to Interpret the Result
The output is mass per volume. A value of 1.20 kg/m³ means one cubic metre of air has a mass of about 1.20 kilograms under the specified conditions. Density is useful in contexts such as weather analysis, estimating buoyancy, and understanding how air conditions affect aerodynamic forces. For a fixed object moving through air, aerodynamic drag depends partly on density, but also on speed, shape, and drag coefficient; density alone does not determine the force.
The dry-air output helps show the humidity effect at the same total pressure and temperature. It is not a second estimate that should be averaged with the moist-air answer. At 0% relative humidity the two values coincide in this model. As humidity rises, the moist-air value tends to fall slightly, though the size of the change is often smaller than the effects of a substantial temperature or pressure change.
Limits and Common Mistakes
This is a practical estimate, not a precision measurement. The ideal-gas approximation works well for ordinary atmospheric conditions, but the saturation-pressure expression and fixed gas constants introduce small approximations. Near freezing, over very hot surfaces, at high pressures, or when precision matters for engineering or research, use a more complete moist-air model and traceable measurements.
- Using sea-level pressure as local pressure: this makes the estimated density too high at an elevated site, unless pressure has been converted appropriately.
- Entering °F as °C: convert first with °C = (°F − 32) × 5/9.
- Confusing humidity formats: 50% is entered as 50, not 0.50.
- Assuming elevation determines today’s density: elevation provides context, but actual pressure and weather conditions are needed for a current estimate.
Frequently Asked Questions
What is the air density in Wisconsin?
There is no single statewide value. It depends on local pressure, temperature, humidity, elevation, and weather at the time. Under the calculator’s default conditions, the estimate is 1.199 kg/m³.
Is air thinner in Wisconsin’s higher-elevation areas?
Usually, yes, if conditions are otherwise comparable. Atmospheric pressure tends to be lower at higher elevation, reducing air density. Day-to-day weather and temperature can change the comparison.
Does humidity make air heavier?
At fixed temperature and total pressure, humid air is generally less dense than dry air. Water vapour has a lower molecular mass than the nitrogen and oxygen it partly displaces.
What pressure should I enter?
Use station pressure at the site’s elevation when possible. A sea-level-adjusted pressure is not the same as the pressure actually present at your location.
How much does temperature change air density?
At constant pressure and humidity, raising temperature lowers density. The exact change depends on the starting temperature and moisture content; enter the conditions into the calculator for a specific comparison.
Related
Formula used
in p | Atmospheric pressure | kPa | 101.325 | 0 in t | Air temperature | °C | 20 | -273.15 in rh | Relative humidity | % | 50 | 0 | 100 out rho | Moist air density | kg/m³ | (p * 1000 - (rh / 100) * 611.2 * exp(17.67 * t / (t + 243.5))) / (287.05 * (t + 273.15)) + ((rh / 100) * 611.2 * exp(17.67 * t / (t + 243.5))) / (461.495 * (t + 273.15)) | 3 out dry | Dry-air density at same pressure and temperature | kg/m³ | p * 1000 / (287.05 * (t + 273.15)) | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Isotope Percent Abundance Calculator and How to Use It75.91 %
- Percentage Abundance Calculator and How to Find It
- Isotope Fractional Abundance Calculator and Formula0.2409 fraction
- Percent Abundance Formula: Calculate Isotope Percentages25.00 %
- Isotope Percent Abundance Calculator and How to Use It50.00 %
- Isotope Percent Abundance Calculator and How-To Guide75.91 %