molecalculator

Moles & Molar Mass

Class 6 Road Base Quantity Calculator

Calculator No. 01-6713 · Updated · Formula and assumptions shown below

Compacted road base volume 60.000 m3
Estimated compacted material mass
132.00 t
= Compacted road base volume × Compacted bulk density ÷ 1000
Road length
100 m
Set in the form below
Road width
4 m
Set in the form below
You enter
Road length (m), Road width (m), Compacted base depth (mm), Compacted bulk density (kg/m3)
You get
Compacted road base volume (m3), Estimated compacted material mass (t)
Rounding
3 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A Class 6 road base quantity calculator estimates the compacted aggregate volume and approximate material mass needed from the road’s length, width, and finished base depth. Enter those dimensions and the material’s bulk density; the calculator returns cubic metres and tonnes, but the supplier’s grading and density information should be used for ordering.

Formula

The calculator first finds the compacted layer volume, then multiplies that volume by the entered compacted bulk density to estimate mass:

V = L × W × (D ÷ 1000)
M = V × ρ ÷ 1000

  • V is compacted volume in cubic metres (m³).
  • L is road length in metres (m).
  • W is base width in metres (m).
  • D is finished compacted depth in millimetres (mm). Dividing by 1000 converts millimetres to metres.
  • M is estimated material mass in tonnes (t). Dividing kilograms by 1000 converts to tonnes.
  • ρ is the entered compacted bulk density in kilograms per cubic metre (kg/m³).

Volume is geometric: it does not depend on the aggregate type. Mass does depend on density and moisture, so the default density is an illustrative planning value, not a universal specification. Replace it with a value supplied for the actual Class 6 material and measurement condition.

Worked Example

Using the calculator’s default values—length 100 m, width 4 m, compacted depth 150 mm, and density 2,200 kg/m³:

  1. Convert depth: 150 mm ÷ 1000 = 0.15 m.
  2. Find compacted volume: 100 m × 4 m × 0.15 m = 60.000 m³.
  3. Estimate mass: 60.000 m³ × 2,200 kg/m³ ÷ 1000 = 132.00 t.

The calculator therefore gives 60.000 m³ of compacted base and an estimated 132.00 tonnes. The mass result follows the assumed density; it is not a guaranteed delivery quantity or a substitute for a supplier’s weighbridge or load calculation.

Assumptions

  • The road base is a uniform rectangular layer with constant width and finished depth.
  • Depth is the compacted depth, not the loose depth before rolling.
  • The entered density represents the compacted material in the condition relevant to the estimate.
  • The calculation excludes shoulders, side slopes, curves, intersections, localized thickening, and wastage unless those areas are added separately.

What “Class 6” Means

“Class 6” is a material classification used in some road and earthworks specifications, not a single globally consistent recipe. The grading limits, source requirements, durability tests, and permitted uses depend on the applicable road authority or project specification. The term alone does not establish a universal density, layer thickness, or ordering conversion.

Before estimating, check the project documents for the required material class and construction details. A supplier may describe products using local terminology or provide a grading designation that needs to be matched to the specification. For a public road or engineered access, the project’s drawings and written requirements take priority over a generic online estimate.

How to Measure and Use the Result

Measure the area that will actually receive the base. For a straight section with consistent width, length multiplied by width gives the plan area. Use the specified finished layer depth; if depth varies, split the road into sections and calculate each volume separately, then add the results.

  • Set length and width: Use metres. For a non-rectangular area, break the layout into rectangles or other simple shapes and total their areas.
  • Enter depth: Use millimetres in this calculator. A 150 mm layer is entered as 150, not 0.15.
  • Set density: Ask for the relevant bulk density and whether it refers to compacted or loose material, and whether it is measured wet or dry.
  • Review both outputs: Volume helps with geometric planning; estimated tonnes can help frame a delivery enquiry.
  • Confirm the order: Ask the supplier how its quoted tonnes relate to moisture and loading, and allow for site-specific construction needs.

For example, a road with changing depth can be divided into 60 m at 150 mm and 40 m at 200 mm, both 4 m wide. Calculate the sections individually: 60 × 4 × 0.15 = 36 m³, and 40 × 4 × 0.20 = 32 m³. The total compacted volume is 68 m³. This is more accurate than applying one average depth when the actual profile is known.

Ordering, Compaction, and Common Errors

The calculator estimates the volume of the finished, compacted layer. Loose aggregate occupies a different volume because particles settle and interlock during compaction. Do not assume that a loose delivery volume equals the finished volume, or apply a generic “compaction factor” without project or supplier guidance. If ordering is by tonne, a suitable density conversion is necessary; if ordering by cubic metre, clarify whether that means loose or compacted volume.

  • Mixing units: Entering 0.15 as a millimetre depth makes the result 1,000 times too small. Enter 150 for a 150 mm layer.
  • Using the wrong width: Decide whether the base extends beyond the travelled surface or includes shoulders, then measure that full specified width.
  • Treating density as fixed: Aggregate source, grading, moisture, and compaction affect bulk density. Use project-specific or supplier information where available.
  • Forgetting separate areas: Add entrances, passing bays, shoulders, and widened bends if they are part of the work.
  • Rounding too early: Keep the section calculations unrounded and round only the final estimate to a practical level.

Actual construction may also require attention to subgrade condition, drainage, placement in suitable lifts, and specified compaction testing. Those requirements cannot be determined from a quantity calculation; follow the applicable design and construction specification.

Frequently Asked Questions

How many tonnes of Class 6 road base do I need?
Calculate compacted volume from length × width × depth, then multiply by an applicable density and divide by 1,000 to convert kilograms to tonnes. Because density varies, confirm the value and ordering basis with the supplier.

How do I calculate cubic metres of road base?
Convert the compacted depth to metres and multiply length × width × depth. For example, 100 m × 4 m × 0.15 m equals 60 m³.

Is 150 mm the correct depth for Class 6 road base?
There is no universal depth implied by the words “Class 6.” Required thickness depends on the design, ground conditions, traffic, drainage, and local specification; use the project’s specified compacted depth.

Does the calculator include compaction allowance?
No. It calculates the finished compacted volume and estimates mass using the density entered. Loose-to-compacted conversion should come from the project specification or material supplier, not an assumed universal factor.

Can I use the result to order material?
Use it as a planning estimate, then confirm material classification, density, moisture basis, and whether the supplier sells by loose volume or tonne. Include any separately measured shoulders or extra areas before placing an order.

Related

Formula used
in len | Road length | m | 100 | 0
in wid | Road width | m | 4 | 0
in dep | Compacted base depth | mm | 150 | 0
in den | Compacted bulk density | kg/m3 | 2200 | 0
out vol | Compacted road base volume | m3 | len * wid * (dep / 1000) | 3
out mass | Estimated compacted material mass | t | vol * den / 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →