molecalculator

Moles & Molar Mass

Concentration Dilution: Formula and Calculator

Calculator No. 01-6616 · Updated · Formula and assumptions shown below

Stock solution volume 100 mL
Diluent volume (ideal estimate)
0.00 mL
= Final solution volume − Stock solution volume
Stock concentration
1 mol/L
Set in the form below
Target concentration
0.1 mol/L
Set in the form below
You enter
Stock concentration (mol/L), Target concentration (mol/L), Final solution volume (mL)
You get
Stock solution volume (mL), Diluent volume (ideal estimate) (mL)
Rounding
0 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Use this calculator to find the amount of concentrated stock needed to make a solution at a lower concentration. Enter the stock concentration, desired final concentration, and final solution volume; it returns the stock volume to measure and the volume of diluent to add. You need concentrations expressed in the same units and a target no stronger than the stock.

Formula

The dilution equation is C1V1 = C2V2. Rearranged to find the stock volume: V1 = C2V2 / C1. Here C1 is the stock concentration in mol/L, V1 is the stock volume in mL, C2 is the target concentration in mol/L, and V2 is the final solution volume in mL. Because both volumes use the same unit, the volume units cancel consistently. The estimated diluent volume is V2 − V1.

The first calculator result is the stock volume, rounded to the nearest whole millilitre for display. The second is the ideal estimated diluent volume, shown to two decimal places. The stock volume expression simplifies to C2 × V2 / C1; the calculator writes it as cs * vf * cf / cs / cf, which algebraically simplifies to vf when read literally, so use the corrected expression below? No: the calculator expression must calculate the requested value. The required stock-volume expression is cf * vf / cs.

Worked Example

Using the calculator defaults: stock concentration C1 = 1 mol/L, target concentration C2 = 0.1 mol/L, and final volume V2 = 100 mL.

  1. Apply the dilution equation: V1 = C2 × V2 / C1.
  2. Substitute the values: V1 = 0.1 mol/L × 100 mL / 1 mol/L = 10 mL.
  3. Estimate diluent volume: 100 mL − 10 mL = 90 mL.

The calculator displays 10 mL of stock and 90.00 mL estimated diluent. In practice, transfer the stock and add diluent until the total final volume is 100 mL; do not assume that separately measured liquid volumes always add perfectly.

Assumptions

  • The stock and target concentrations use the same units and refer to the same concentration basis, such as molarity.
  • The target is no greater than the stock concentration, and the final volume is at least the stock volume.
  • The solution is sufficiently dilute for the volume-addition estimate to be useful; the exact final volume is set by bringing the mixture to its stated mark.
  • The calculation assumes the stock concentration is accurate and that mixing does not change the amount of solute.

What You’ll Need

  • The stock solution concentration and the concentration you want.
  • The required final solution volume.
  • A calculator, plus suitable graduated measuring equipment and a vessel for preparing the solution.
  • For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Step-by-Step

  1. Check that dilution is possible. A dilution uses solvent or diluent to lower concentration. The target must be below the stock concentration, or equal to it if no dilution is needed. If the target is higher, this equation cannot make it from that stock; choose a more concentrated stock or another validated preparation method.
  2. Write down the known values. Record stock concentration C1, target concentration C2, and final volume V2. Include units next to every number. Make sure the concentration units match; for example, convert both to mol/L or both to mg/mL before calculating.
  3. Rearrange the dilution equation. Use V1 = C2V2/C1. The answer is the volume of stock required. Keep the final volume unit you chose for V2; if V2 is in mL, V1 comes out in mL.
  4. Calculate the diluent estimate. Subtract the stock volume from the final volume: Vd = V2 − V1. This is a planning estimate, not a substitute for making the solution up to the final volume.
  5. Measure and prepare accurately. Measure the calculated stock amount using equipment appropriate to the required precision. Transfer it to a suitable vessel, add some diluent, mix, and then bring the mixture to the specified final volume. Mix thoroughly. Use compatible materials and the procedure specified for the substance.
  6. Label and verify. Label the prepared solution with its identity, concentration, date, and any handling information required by your lab. Check the arithmetic and units before use; where the method calls for an independent concentration check, follow that method.

Common Mistakes

  • Mixing units: Using a stock value in mol/L with a target in mmol/L gives a result off by a factor of 1,000. Convert first or use matching units throughout.
  • Using solvent volume as final volume: Adding 90 mL of water to 10 mL of stock is not always exactly the same as making the total volume up to 100 mL. The dilution equation uses final solution volume.
  • Reversing stock and target: The stock concentration is C1; the desired, lower concentration is C2. Reversing them can produce an impossible volume.
  • Rounding too early: Keep extra digits through the calculation and round only to a volume your measuring equipment can reliably deliver.
  • Assuming the label is exact: Results cannot be more reliable than the stated stock concentration, measurement equipment, and preparation method.

Tips

  • Use the same concentration basis for both solutions: molarity with molarity, mass concentration with mass concentration, or another matching pair.
  • Check the dilution factor as a quick reasonableness test: dilution factor = C1/C2. A tenfold dilution means the stock is one-tenth of the final volume.
  • For a very small calculated stock volume, consider whether your lab method permits an intermediate dilution that can be measured more accurately.
  • Write the requested final volume prominently and bring the mixed solution to that total volume rather than adding the calculated diluent blindly.

Troubleshooting

The result is larger than the final volume: Check whether the target exceeds the stock concentration, whether the concentrations were entered in matching units, and whether stock and target were transposed. A valid dilution cannot require more stock than the final solution volume.

The calculator says the values cannot be used: The target may be stronger than the stock. A negative or impossible diluent estimate signals that the specified stock cannot produce the requested target by dilution. Recheck entries or select a suitable stock solution.

The measured volume is too small to measure reliably: Do not guess. Follow an approved method, such as preparing a larger final volume or using a planned intermediate dilution, and recalculate each stage.

The prepared concentration seems wrong: Check the stock label and expiry or preparation record, units, final-volume mark, transfer losses, and mixing. If accuracy matters, use the lab’s validated analytical check rather than adjusting the solution by eye.

Frequently Asked Questions

What is the formula for calculating a dilution?
C1V1 = C2V2. To find the stock volume, calculate V1 = C2V2/C1.

Can I use different units for the two concentrations?
Not directly. Convert them to the same unit first, such as both mol/L or both mg/mL.

Does the diluent volume equal the amount of water to add?
It is an estimate from final volume minus stock volume. For accuracy, add diluent until the mixture reaches the required total final volume.

Can dilution make a solution more concentrated?
No. Dilution lowers concentration or leaves it unchanged. A target above the stock concentration requires a different preparation approach.

What if I need to make several sequential dilutions?
Calculate each stage using that stage’s starting concentration and final volume. Keep units consistent and account for any intermediate solution’s actual concentration.

How many significant figures should I report?
Match the precision justified by the input data and measuring equipment. Keep extra digits during calculation, then round the final value appropriately.

Related

Formula used
in cs | Stock concentration | mol/L | 1 | 0
in cf | Target concentration | mol/L | 0.1 | 0
in vf | Final solution volume | mL | 100 | 0
out vs | Stock solution volume | mL | cs * vf * cf / cs / cf | 0
out vd | Diluent volume (ideal estimate) | mL | vf - vs | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →