This calculator converts a colony count from a diluted sample into the estimated concentration of viable, culturable units in the original sample, in CFU/mL. Enter the colonies counted, the dilution fraction plated, and the volume plated in milliliters; the result is the estimated original concentration.
Formula
CFU/mL = colonies counted ÷ (dilution fraction plated × volume plated in mL). The dilution fraction is the fraction of the original sample present in the portion plated: for a 10−4 dilution, enter 0.0001. Its reciprocal is the dilution factor, 10,000 in this example. The volume is the amount of diluted sample spread or otherwise plated, not the volume of the original sample.
- Colonies counted is the number of countable colonies on the plate, in CFU.
- Dilution fraction plated is dimensionless; enter a fraction from greater than zero through 1.
- Volume plated is in mL and must be greater than zero.
- Original concentration is the calculated estimate, in CFU/mL.
The calculation follows from the expected number of colonies: original concentration × dilution fraction × plated volume. Rearranging gives the formula above. A dilution notation such as 10−4 describes the fraction; “1:10,000” describes the same dilution. Do not enter 10,000 as the fraction—the calculator expects 0.0001.
Worked Example
Using the calculator’s defaults: 150 colonies, a plated dilution fraction of 0.0001, and a plated volume of 0.1 mL.
- Find the expected original-sample volume represented on the plate: 0.0001 × 0.1 mL = 0.00001 mL.
- Divide the count by that represented volume: 150 CFU ÷ 0.00001 mL = 15,000,000 CFU/mL.
- Report the result using the calculator’s zero-decimal setting: 15,000,000 CFU/mL. The reciprocal dilution factor is 1 ÷ 0.0001 = 10,000.
Assumptions
- Each counted colony is treated as arising from one viable, culturable unit. A clump of cells may produce one colony, so CFU is not necessarily the same as individual cell count.
- The dilution fraction and plated volume are known and recorded correctly, and the sample was mixed adequately before plating.
- The plate is sufficiently countable, with colonies distinguishable from one another and no major contamination or spreading growth.
- The result estimates the original sample concentration from the plated portion; it is not a direct count of every organism present.
What You’ll Need
- A colony count from a plate made with a known dilution.
- The dilution fraction for that plate, written as a decimal (for example, 10−3 = 0.001).
- The volume of diluted sample plated, converted to mL if necessary.
- Your approved lab method, records, and appropriate protective equipment for the organism and sample.
For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor. This calculation is for study and lab-planning arithmetic; it does not replace local biosafety procedures or validated methods.
Step-by-Step
- Choose the plate to calculate. Use a plate with a documented dilution and plated volume. If replicate plates were made at the same dilution and volume, calculate each separately or use the mean count when the method calls for combining replicates.
- Record the colony count. Count discrete colonies according to your lab’s counting rules. Record the count before applying any dilution correction. Do not use a plate that is too crowded to distinguish colonies or has obvious spreading contamination as if it were a reliable count.
- Write the dilution as a fraction. Convert the dilution on the plate into the fraction of original sample. For example, 10−3 becomes 0.001, and a 1:100 dilution becomes 0.01. If several serial dilutions were made, multiply the fractions for each step. Two 1:10 steps give 0.1 × 0.1 = 0.01, or 10−2.
- Enter the volume plated in mL. A plated volume of 100 µL is 0.1 mL; 1 mL remains 1 mL. Convert units before calculation. The plated volume is not the total volume in the dilution tube.
- Calculate the represented original-sample volume. Multiply the dilution fraction by plated volume. With a 10−3 dilution and 0.1 mL plated, the plate represents 0.001 × 0.1 = 0.0001 mL of original sample.
- Divide colonies by represented volume. Use CFU/mL = count ÷ (fraction × plated volume). Keep the full values during calculation, then round the reported estimate to a precision justified by the count and method.
- Check plausibility and report the details. Include the result, dilution, plated volume, and count, such as “estimated 1.5 × 106 CFU/mL from 150 colonies at 10−3, 0.1 mL plated.” If appropriate, compare results across neighboring dilutions or replicate plates.
Common Mistakes
- Using the reciprocal as the dilution fraction. For 10−4, enter 0.0001, not 10,000. The calculator calculates the reciprocal separately for reference.
- Forgetting plated volume. Dividing only by the dilution fraction assumes 1 mL was plated. If 0.1 mL was plated, omitting the volume makes the estimate ten times too low.
- Mixing µL and mL. Convert microliters to milliliters: divide µL by 1,000. Entering 100 instead of 0.1 for a 100 µL plate changes the answer by a factor of 1,000.
- Using only the last step in a serial dilution. Multiply all dilution fractions from the original sample through the plated tube.
- Reporting false precision. A computed value may contain many digits, but a colony count has sampling variation. Avoid implying more certainty than the count and method support.
- Treating CFU as an exact cell count. One colony can arise from a clump or chain; culture conditions also affect which organisms grow.
Tips
- Write dilution fractions in scientific notation when useful: 0.00001 = 10−5.
- Keep a clear record of every dilution step, the final dilution, plated volume, plate identity, and count.
- When multiple countable plates are available, use your method’s rules for replicate averaging or weighted estimates rather than selecting a result solely because it looks convenient.
- Use a consistent unit. This calculator reports CFU/mL; a result per gram, per swab, or per area requires the appropriate sample-mass or recovery calculation as well.
- Interpret the estimate in context: medium, incubation conditions, sample handling, and organism clumping can affect colony recovery.
Troubleshooting
- The result seems far too high or low: check that the dilution is entered as a fraction, all serial steps were multiplied, and the plated volume is in mL. Recalculate the represented original-sample volume independently.
- The plate is a lawn or colonies overlap: the count may not be reliable. Use a more dilute plate from the same series if it is available and countable, following the lab’s acceptance criteria.
- There are very few or no colonies: the sample may be below the method’s detection range, the dilution may be too great, or viable organisms may not have grown under the conditions used. Report the observation and detection limit according to the method; do not treat zero as proof that the sample contains no viable organisms.
- Replicate plates disagree: review mixing, pipetting, labeling, and counting records. Check for contamination or uneven distribution, and apply the method’s rules for replicate results.
- The dilution is unknown: a valid original concentration cannot be recovered from the colony count alone. Find the preparation record or repeat using a documented dilution.
Frequently Asked Questions
What does CFU/mL mean?
It means colony-forming units per milliliter: an estimate of viable units capable of producing colonies under the specified culture conditions.
How do I enter a 1:100 dilution?
Enter 0.01 as the dilution fraction. If the plated sample underwent further serial dilutions, multiply the fractions and enter the overall fraction for the plated tube.
Do I use the original sample volume or plated volume?
Use the volume of diluted sample placed on the plate. The dilution correction accounts for how much original sample that volume represents.
Can I calculate CFU/mL from a zero-colony plate?
The arithmetic returns zero, but that does not establish that the original sample has no viable units. The result is limited by the tested volume and method’s detection limit.
Should I average counts from different dilutions?
Not by simply averaging raw counts: the plates represent different sample concentrations. Calculate estimates with the correct dilution and volume, then follow your validated method’s rule for combining them.
Is CFU/mL the same as cells/mL?
No. A colony may grow from one cell or a group of cells, and not every cell necessarily grows under the selected conditions. CFU/mL is a culture-based estimate.
Related
Formula used
in colonies | Colonies counted | CFU | 150 | 0 in df | Dilution fraction plated | - | 0.0001 | 0.000000000001 | 1 in vol | Volume plated | mL | 0.1 | 0.000001 out cfu | Original concentration | CFU/mL | colonies / (df * vol) | 0 out dfact | Reciprocal dilution factor | - | 1 / df | 0
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- How to Find the Continuous Decay Rate
- Total Constant of Decay: How to Calculate It0.000121 1/s
- How to Calculate Decay Constant0.000121 1/s
- Half Life GitHub: What It Is and How to Use It
- Decay Constant: How to Calculate It0.000121 1/s
- Half-Life Games in Order: Full Release Timeline