molecalculator

Moles & Molar Mass

Concentration × Molar Mass: Calculate Solute Mass

Calculator No. 01-5389 · Updated · Formula and assumptions shown below

Solute mass 2.9220 g
Concentration
200.00 mM
= Target molarity × 1000
Target molarity
0.2 mol/L
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Target molarity (mol/L), Molar mass (g/mol), Final solution volume (mL)
You get
Solute mass (g), Concentration (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Concentration × molar mass is not, by itself, a complete concentration calculation: the units and the quantity you want matter. This calculator uses a target molarity, a compound’s molar mass, and a final solution volume to calculate the mass of solute; it also reports the resulting concentration in millimolar units.

Formula

The mass of solute is the target molarity multiplied by the substance’s molar mass and the final solution volume in liters:

m = c × M × (V / 1000)

  • m is the solute mass in grams (g).
  • c is the target molar concentration in moles per liter (mol/L).
  • M is the molar mass in grams per mole (g/mol).
  • V is the final solution volume in milliliters (mL); dividing by 1000 converts milliliters to liters.

The unit cancellation is mol/L × g/mol × L = g. The concentration conversion is concentration in mM = c × 1000, because one mol/L equals 1000 millimoles per liter. The calculator treats the entered molarity as the target concentration; the millimolar output is that same target expressed in another unit.

Worked Example

Using the calculator’s defaults: target molarity c = 0.2 mol/L, molar mass M = 58.44 g/mol, and final volume V = 250 mL.

  1. Convert the final volume: 250 mL / 1000 = 0.25 L.
  2. Calculate mass: m = 0.2 mol/L × 58.44 g/mol × 0.25 L = 2.922 g.
  3. Convert the target concentration: 0.2 mol/L × 1000 = 200 mM.

The outputs are 2.9220 g of solute and 200.00 mM. The mass is displayed to four decimal places; the concentration is displayed to two.

Assumptions

  • The requested volume is the final solution volume, not the amount of solvent added.
  • The molarity is the target concentration of the prepared solution.
  • The entered molar mass applies to the exact chemical form being considered, including any specified hydrate or salt form.
  • This is arithmetic for study and lab planning, not a substitute for a validated experimental method.

What Concentration × Molar Mass Means

Molarity describes the amount of dissolved substance per volume: 0.2 mol/L means 0.2 moles of solute in each liter of final solution. Molar mass converts that amount in moles into a mass in grams. Multiplying by the volume gives the amount needed for a particular batch.

For example, a target of 0.2 mol/L for 0.25 L requires 0.05 mol of solute. A substance with molar mass 58.44 g/mol therefore requires 0.05 mol × 58.44 g/mol = 2.922 g. The calculator combines these steps in one equation.

This is useful when preparing a solution from a weighed solid or checking a theoretical recipe. It does not calculate a mass from concentration alone: volume and molar mass are also necessary. Nor does it determine the concentration of an existing sample unless its solute amount and volume are known.

Choosing the Right Inputs

Use a molar mass that matches the material’s formula, not just a familiar name. A salt, hydrate, or other formulated chemical can have a different molar mass from its anhydrous or parent compound. For a compound’s molar mass, add the atomic weights in its chemical formula; use the relevant chemical form shown on its label or in an authoritative reference.

  • Molarity: enter mol/L, not mM. Convert mM to mol/L by dividing by 1000; for instance, 200 mM is 0.2 mol/L.
  • Molar mass: enter g/mol. If a source gives kg/mol, convert to g/mol by multiplying by 1000.
  • Volume: enter the intended final volume in mL. The calculator converts it to liters internally.

Keep adequate precision in the inputs. Rounding molar mass or volume too early can shift the calculated mass, especially in small preparations. The displayed digits are arithmetic output, not a guarantee that a balance or volume measurement can achieve that precision.

Common Errors and Limits

A frequent mistake is to multiply a number in millimolar directly by a molar mass as if the concentration were in mol/L. Since mM is 1000 times smaller than mol/L for the same numeric value, convert it first. Another common error is entering a solvent volume where the formula needs final solution volume. Dissolving a solid can change the volume; the intended quantity is the volume after the solution has been brought to its final mark or target.

The calculation assumes the entered concentration is a meaningful target for the solution. It does not account for purity, water content, chemical reactions, incomplete dissolution, volume contraction, or temperature-dependent volume changes. If a reagent’s assay or purity is below 100%, a separate correction may be needed based on reliable material information; this calculator does not apply one.

Molarity is defined per liter of solution and can vary slightly with temperature because liquid volume changes. For routine calculations, use the temperature and preparation conventions specified by the applicable method. For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.

Frequently Asked Questions

What does concentration times molar mass give?
Concentration in mol/L multiplied by molar mass in g/mol gives mass concentration in g/L. Multiplying that result by a volume in liters gives the required solute mass in grams.

How do I calculate grams from molarity?
Multiply molarity (mol/L) by molar mass (g/mol) and by final volume in liters. If volume is entered in milliliters, divide it by 1000 first.

Is 1 M the same as 1 mM?
No. 1 M is 1 mol/L, while 1 mM is 0.001 mol/L. One molar is 1000 millimolar.

Does the volume mean solvent volume or final solution volume?
It means final solution volume. The solvent amount may be less than that because the dissolved solute occupies volume too.

Why does the chemical form change the answer?
Different forms can have different molar masses. For example, a hydrate includes water molecules in its formula, so its mass per mole differs from the anhydrous compound. Use the molar mass for the actual form specified.

Related

Formula used
in c | Target molarity | mol/L | 0.2 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out m | Solute mass | g | c * mm * (v / 1000) | 4
out cm | Concentration | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →