Constant-volume and variable-volume HVAC systems differ in how they deliver air: a constant-volume system supplies a largely fixed airflow and changes its temperature, while a variable-air-volume (VAV) system varies airflow to help meet each zone’s heating or cooling demand. The calculator below compares their airflow and fan-energy implications using your inputs; it returns the estimated airflow reduction and idealized fan-power ratio, not a complete building energy analysis.
Formula
The airflow reduction is (1 − Q2 / Q1) × 100. The idealized fan-power ratio is (Q2 / Q1)3, and estimated reduced-flow fan power is P1 × (Q2 / Q1)3. Q1 is the reference airflow in litres per second, Q2 is the lower airflow in litres per second, and P1 is reference fan power in kilowatts. The calculation assumes the same fan and an idealized cubic relationship between flow and power. The inputs should represent the same system and operating point; this simplified comparison does not model a real fan curve or controls.
Worked Example
Using the defaults, Q1 = 1000 L/s, Q2 = 700 L/s, and P1 = 2 kW.
- Airflow reduction = (1 − 700 / 1000) × 100 = 30.0%.
- Flow ratio = 700 / 1000 = 0.70000.
- Idealized fan-power ratio = 0.700003 = 0.343.
- Estimated reduced-flow fan power = 2 × 0.343 = 0.686 kW.
So reducing airflow by 30% gives an idealized fan-power estimate of 0.686 kW, about 34.3% of the 2 kW reference. Actual power savings may differ substantially.
Assumptions
- The airflow readings describe the same system and comparable conditions.
- The cubic fan-law approximation is used as an estimate, not a measured result.
- Fan efficiency, static-pressure control, duct leakage, coil performance, and heating or cooling loads are not calculated.
How the Two Systems Work
In a constant-volume (CV) arrangement, supply air moves at roughly one design airflow when the system operates. A thermostat’s demand is commonly met by changing the supply-air temperature, for example by cooling or heating air at a central coil. Some installations use reheat or other controls, so “constant volume” does not mean every part of the system is mechanically simple or that airflow is perfectly unchanged under all conditions.
A VAV system typically supplies air through a central duct network, then uses a terminal unit or damper to adjust the airflow delivered to each zone. The central fan often slows as overall demand falls, commonly through a variable-speed drive and pressure controls. The supply-air temperature may also be reset within system limits. VAV therefore varies both the distribution of air across zones and, often, total system airflow.
These terms describe air-delivery strategies, not a guarantee of comfort, efficiency, or a particular equipment type. Both approaches can be designed for heating and cooling, and either can be poorly controlled or well tuned.
What the Calculator Can—and Cannot—Tell You
The calculator illustrates why reduced airflow can lower fan energy. Under ideal fan laws, power varies approximately with the cube of airflow when speed changes and other conditions are suitable. A 10% airflow reduction would therefore imply a power ratio of 0.93, or 0.729, in that idealized case. This is not a prediction that every building will save exactly 27.1%: real fans operate on performance curves, and system pressure, efficiency, minimum airflow, and control strategy matter.
It does not compare total heating and cooling energy. Lower airflow may affect coil operation, supply temperatures, ventilation, humidity control, and reheat. Nor does the calculation determine whether a given zone receives enough outdoor air. A design or retrofit decision needs measured or modeled loads, equipment data, applicable ventilation requirements, and commissioning.
How to Choose Between Constant and Variable Volume
Start with the use of the space and whether its zones have meaningfully different or changing loads. A large open area with similar schedules may be served adequately by a simpler fixed-airflow strategy. A building with multiple zones, changing occupancy, solar gains, or varying schedules may benefit from VAV’s ability to adjust delivery zone by zone.
- Load diversity: VAV can respond as zones’ demands change independently; a constant-volume system may condition the whole supply stream even when only some zones need full output.
- Ventilation: Check outdoor-air delivery at minimum flow as well as at design flow. Lower supply airflow must not undermine required ventilation.
- Controls and maintenance: VAV depends on correctly configured sensors, dampers, pressure control, and minimum-flow settings. More control points can mean more commissioning and maintenance work.
- Noise and comfort: Air velocity, diffuser selection, duct design, and control stability affect drafts and sound in either system.
- Existing equipment: A change in system type may require duct, fan, terminal, electrical, or controls work. Compare lifecycle costs, not just the fan or terminal-unit price.
There is no universal winner. A sound choice weighs first cost, operating hours, energy prices, maintenance capacity, ventilation needs, and the building’s actual load profile. Energy modeling and a qualified HVAC assessment are more reliable than applying the calculator’s fan-law estimate to a whole building.
Common Misconceptions and Problems
A frequent misconception is that VAV always saves energy. It can reduce fan energy when airflow and fan speed fall, but excessive minimum airflow, poor static-pressure settings, leaky ducts, or simultaneous cooling and reheat can erase savings. Another misconception is that “variable volume” means the supply air is always changing temperature; airflow modulation is the defining feature, though temperature reset may also be used.
Low-flow comfort complaints can point to inadequate diffuser performance, incorrect balancing, a faulty sensor, or a zone’s minimum setting—not necessarily an inherent flaw in VAV. Conversely, a constant-volume system may maintain steady delivery but still have uneven room conditions if the zones, ducts, or controls are not properly designed. Diagnose operation with airflow and temperature measurements and control trends rather than assuming the system label explains the problem.
Frequently Asked Questions
Is VAV more efficient than constant volume?
It can be, especially when loads vary and the central fan can reduce speed. Actual savings depend on controls, ventilation minimums, fan performance, and heating or cooling operation.
What does constant volume mean in HVAC?
It means the system is designed to deliver a largely fixed airflow while meeting demand mainly by changing the air’s temperature. The precise behavior depends on the system and its controls.
Does VAV change air temperature or airflow?
Its defining action is changing airflow to a zone. Many systems also adjust supply-air temperature, but that is a separate control function.
Can VAV reduce fan energy?
Often, if the fan slows as total airflow falls. The cubic fan-law estimate is an idealization; actual savings require fan and system data or measurement.
Is constant volume simpler to maintain?
It may have fewer zone airflow controls, but maintenance still depends on equipment and design. VAV has additional terminals and control points that need setup and periodic checking.
Which system is better for a multi-zone building?
VAV is often considered where zone loads vary independently, but the right choice depends on ventilation, schedules, costs, and operational capability—not zone count alone.
Related
Formula used
in q1 | Constant airflow | L/s | 1000 | 0 in q2 | Reduced VAV airflow | L/s | 700 | 0 in p1 | Constant-system fan power | kW | 2 | 0 out reduction | Airflow reduction | % | (1 - q2 / q1) * 100 | 1 out ratio | VAV fan-power ratio | - | (q2 / q1)^3 | 3 out p2 | Idealized VAV fan power | kW | p1 * (q2 / q1)^3 | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Cubic Meters per Hour to Liters per Second0.2778 L/s