molecalculator

Moles & Molar Mass

Liters to Cubic Feet Calculator and Conversion Formula

Calculator No. 01-6371 · Updated · Formula and assumptions shown below

Volume 3.5315 ft³
Volume using exact conversion
3.5315 ft³
= Volume ÷ 28.316846592
Volume
100 L
Set in the form below
You enter
Volume (L)
You get
Volume (ft³), Volume using exact conversion (ft³)
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Convert liters to cubic feet by multiplying the number of liters by 0.0353146667; one liter equals exactly 0.0353146667 cubic feet when the result is rounded to ten decimal places. Enter a volume in liters to get its equivalent in cubic feet, with the reverse conversion available by multiplying cubic feet by 28.316846592.

Formula

The conversion formula is: cubic feet = liters × 0.0353146667. In symbols, Vft³ = VL × 0.0353146667. Here, Vft³ is volume in cubic feet and VL is volume in liters. The factor is the reciprocal of 28.316846592 liters per cubic foot. The calculator’s first result uses the displayed factor; the second uses the reciprocal form. They agree at the shown precision.

Worked Example

For the default input of 100 L:

  1. Use cubic feet = liters × 0.0353146667.
  2. Substitute 100 L: 100 × 0.0353146667 = 3.53146667 ft³.
  3. Rounded to four decimal places, the result is 3.5315 ft³.

The reciprocal calculation gives 100 / 28.316846592 = 3.531466672… ft³, which also rounds to 3.5315 ft³.

Assumptions

  • The input is a volume expressed in liters, not a length or a mass.
  • The conversion uses the standard definition 1 ft³ = 28.316846592 L.
  • The displayed results are rounded to four decimal places; extra digits in the input do not make a rounded result more precise than the measurement.

How the Conversion Works

A liter and a cubic foot are both units of volume, so the conversion is a fixed ratio. The liter is a metric unit equal to one cubic decimeter: a cube measuring 10 centimeters on each side has a volume of one liter. A cubic foot is the volume of a cube whose sides are each one foot long. Since one international foot is exactly 0.3048 meters, a cubic foot is 0.028316846592 cubic meters, or 28.316846592 liters.

Dividing 1 liter by the number of liters in one cubic foot gives the multiplier:

1 / 28.316846592 = 0.0353146667 cubic feet per liter, approximately.

For example, 1 L is about 0.0353 ft³, while 1 ft³ is about 28.3168 L. These are reciprocal conversions, not competing definitions.

Quick Conversion Examples

  • 5 L × 0.0353146667 = about 0.1766 ft³.
  • 20 L × 0.0353146667 = about 0.7063 ft³.
  • 50 L × 0.0353146667 = about 1.7657 ft³.
  • 200 L × 0.0353146667 = about 7.0629 ft³.
  • 1,000 L × 0.0353146667 = about 35.3147 ft³.

For a quick estimate, 1 liter is roughly 0.035 cubic feet, and 1 cubic foot is roughly 28.3 liters. Use the more precise factor when calculating container capacity, comparing specifications, or checking a measurement where small differences matter. Avoid rounding each intermediate step; keep the full factor and round only the final answer.

When to Use Each Unit

Liters are common for liquid volumes and metric container specifications. Cubic feet are often used for room, storage, appliance, and shipping capacity in settings that use customary units. Converting between them can help compare a product’s stated capacity with the available space or with a specification in another unit system.

Volume is not the same as the dimensions of a container. A rectangular space can be measured in feet and its volume calculated by multiplying length × width × height, with all three measurements in feet; the result is cubic feet. If the same dimensions are in centimeters, convert or calculate in consistent units before comparing. A container’s advertised capacity may also differ from its usable capacity because walls, fittings, or a required fill gap take up space.

Nor does a volume conversion give a mass. To convert liters of a substance into kilograms or pounds, its density is also needed. Water is close to 1 kilogram per liter under ordinary conditions, but that relationship does not apply universally to other liquids or to all temperatures.

Common Conversion Mistakes

  • Multiplying in the wrong direction: liters to cubic feet uses 0.0353146667, a factor smaller than one. Cubic feet to liters uses 28.316846592.
  • Confusing cubic feet with square feet: ft³ measures volume; ft² measures area. A volume conversion cannot be made using a length or area factor.
  • Mixing units within a calculation: convert all dimensions to the same unit before multiplying length, width, and height.
  • Rounding too early: retaining the conversion factor until the final step prevents avoidable rounding differences.
  • Assuming a nominal container size is exact: labels and product specifications can be rounded, and internal usable volume may be lower than the external dimensions suggest.

Frequently Asked Questions

How many cubic feet are in one liter?
One liter is approximately 0.0353147 cubic feet. For a quick estimate, use 0.0353 ft³ per liter.

How many liters are in one cubic foot?
One cubic foot equals exactly 28.316846592 liters under the standard definitions of the units. It is commonly rounded to 28.32 L.

How do I convert liters to cubic feet by hand?
Multiply the liter value by 0.0353146667. For example, 30 L × 0.0353146667 is about 1.0594 ft³.

Is a liter the same as a cubic meter?
No. One cubic meter equals 1,000 liters. A liter is one-thousandth of a cubic meter and equals one cubic decimeter.

Can I convert liters to cubic feet for a rectangular tank?
Yes, if you know its volume in liters. If you only know its dimensions, calculate the volume using consistent units first; multiply dimensions in feet to get cubic feet, or convert the resulting volume to liters as needed.

Does this conversion depend on temperature?
The unit conversion itself does not depend on temperature. The physical volume of a liquid can change as its temperature changes, but once a volume is stated in liters, the same liters-to-cubic-feet factor applies.

Related

Formula used
in l | Volume | L | 100 | 0
out ft3 | Volume | ft³ | l * 0.0353146667 | 4
out ft3exact | Volume using exact conversion | ft³ | l / 28.316846592 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →