Convert cubic meters per second (m³/s) to liters per second (L/s) by multiplying by 1,000: 1 m³/s = 1,000 L/s. Enter a flow rate in m³/s to calculate the equivalent L/s; the result is a volumetric flow rate, not a volume.
Formula
Liters per second equals cubic meters per second multiplied by 1,000:
QL/s = Qm³/s × 1,000
- Qm³/s is the volumetric flow rate in cubic meters per second.
- QL/s is the same flow rate in liters per second.
- The factor 1,000 comes from the exact volume relationship 1 m³ = 1,000 L.
The second output converts the same input to cubic meters per hour. There are 3,600 seconds in an hour, so Qm³/h = Qm³/s × 3,600. It is a separate time-unit conversion, not part of the liters-per-second formula.
Worked Example
Using the default input, q = 0.01 m³/s:
- Convert cubic meters to liters: 0.01 m³/s × 1,000 L/m³ = 10 L/s.
- Convert seconds to hours for the additional output: 0.01 m³/s × 3,600 s/h = 36 m³/h.
The calculator therefore returns 10.00 L/s and 36.00 m³/h. These are two ways to express the same steady flow rate.
Assumptions
- The input is a volumetric flow rate in m³/s, not a volume in m³.
- The flow rate is expressed over the time unit specified in the input. The conversion does not assume a particular fluid, density, pressure, or temperature.
- The conversion is an exact unit conversion; the displayed decimal places are for readability and do not imply measurement precision.
How the Conversion Works
A cubic meter is a unit of volume, while a liter is a smaller unit of volume. Since one cubic meter contains exactly 1,000 liters, a rate measured in cubic meters each second contains 1,000 times as many liters each second. The time unit stays the same, so only the volume unit changes.
For example, 2 m³/s means two cubic meters pass a point every second. Multiplying by 1,000 gives 2,000 L/s. The multiplier is not 1,000,000: that larger factor applies when converting cubic meters to milliliters, because each liter contains 1,000 milliliters.
To convert in the other direction, divide liters per second by 1,000:
Qm³/s = QL/s ÷ 1,000
Thus, 250 L/s equals 0.25 m³/s. A quick check is that the numerical value in L/s should be 1,000 times the value in m³/s.
Examples and Related Flow Units
These examples show the scale of the conversion and how a time-unit change affects the result:
- 0.001 m³/s = 1 L/s.
- 0.025 m³/s = 25 L/s.
- 1 m³/s = 1,000 L/s, or 3,600 m³/h.
- 0.5 m³/s = 500 L/s, or 1,800 m³/h.
For liters per minute, multiply m³/s by 60,000: one cubic meter contains 1,000 liters, and one second-based rate must be multiplied by 60 to express it per minute. For instance, 0.01 m³/s is 600 L/min. To convert L/s to L/min, multiply by 60; to convert L/s to m³/h, multiply by 3.6.
Keep the units attached to each number. A volume such as 10 m³ is not a rate. If that volume passes through a pipe in 20 seconds, the average flow rate is 10 ÷ 20 = 0.5 m³/s, which is 500 L/s. Without a time interval, a volume cannot be converted to a flow rate.
When to Use the Result and Common Mistakes
This conversion is useful when comparing flow readings or specifications written in different units, such as a measured channel flow in m³/s and a pump or process requirement in L/s. It changes units only. It does not calculate the flow from pipe dimensions, pressure, fluid properties, or a measurement of volume over time; those require additional information.
- Check whether the unit is m³/s or m³/h. For m³/h to L/s, divide by 3.6, not multiply by 1,000 alone. The time unit must be converted as well.
- Do not confuse flow rate with capacity. A tank’s volume in liters says how much it holds, not how quickly it fills.
- Keep the original precision. A result such as 10.00 L/s is rounded for display. If the input measurement has only one significant figure, the extra displayed zeros do not make the measurement more precise.
- Check the decimal scale. A result that is unexpectedly 1,000 times too large or small often indicates that m³ and L were mixed up.
For a variable flow, a single rate may describe an instantaneous reading or an average over a stated period. The conversion works for either, but the value’s meaning depends on how it was measured. To find average flow from a known volume, divide that volume by the elapsed time, first expressing both in compatible units.
Frequently Asked Questions
How many liters per second are in 1 cubic meter per second?
There are 1,000 L/s in 1 m³/s because 1 m³ equals 1,000 L.
How do I convert m³/s to L/s?
Multiply the value in m³/s by 1,000. For example, 0.04 m³/s × 1,000 = 40 L/s.
How do I convert liters per second back to cubic meters per second?
Divide the L/s value by 1,000. For example, 75 L/s ÷ 1,000 = 0.075 m³/s.
How many liters per second is 1 m³/h?
One m³/h is 1,000 liters per hour. Dividing by 3,600 seconds per hour gives about 0.2778 L/s.
Can I convert cubic meters to liters per second without knowing the time?
No. Cubic meters alone measure volume. To get a rate in L/s, you need a duration or an already measured flow rate.
Related
Formula used
in q | Flow rate | m³/s | 0.01 | 0 out lps | Flow rate | L/s | q * 1000 | 2 out m3h | Flow rate | m³/h | q * 3600 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Cubic Meters per Second to Litres per Second1,000.000 L/s
- Cubic Meters to Liters per Second Calculator10.00 L/s
- Cubic Meters to Liters: Symbol and Conversion1,000 L
- Cubic Meters per Liter: Conversion and Calculator0.001000 m³
- Cubic Meters to Liters Formula and Calculator1,000 L
- Cubic Meter to Megaliter Converter and Formula1.000 ML