To convert liters to standard cubic feet (scf), multiply the volume in liters by 0.0353147. This conversion assumes the gas is at standard conditions of 60°F (15.6°C) and 14.696 psia (1 atm). The result gives you the equivalent volume in standard cubic feet.
Formula
The conversion from liters to standard cubic feet is based on the relationship between the two volume units and the ideal gas law. The basic volume conversion is:
1 liter = 0.0353147 cubic feet
However, because gas volume depends on temperature and pressure, the conversion must account for the actual conditions versus standard conditions. The full formula is:
scf = L × 0.0353147 × (P_actual / P_std) × (T_std / T_actual)
Where:
- L = volume in liters (L)
- scf = volume in standard cubic feet (scf)
- P_actual = actual pressure (atm)
- P_std = standard pressure = 1 atm (14.696 psia)
- T_actual = actual absolute temperature (K) = °C + 273.15
- T_std = standard absolute temperature = 288.15 K (60°F)
If the gas is already at standard conditions, the pressure and temperature ratios become 1, and the formula simplifies to the volume conversion alone.
Worked Example
Using the default values from the calculator: 100 liters of gas at 15.6°C and 1 atm pressure.
- Convert temperature to Kelvin: T_actual = 15.6 + 273.15 = 288.75 K
- Since pressure is already 1 atm, P_actual/P_std = 1
- Compute the temperature ratio: T_std / T_actual = 288.15 / 288.75 ≈ 0.99792
- Apply the volume conversion: 100 L × 0.0353147 = 3.53147 ft³
- Adjust for conditions: 3.53147 × 1 × 0.99792 ≈ 3.5241 scf
The calculator rounds to 4 decimal places, giving 3.5241 scf.
Assumptions
- The gas behaves as an ideal gas (valid for most gases at moderate pressures and temperatures).
- Standard conditions are defined as 60°F (15.6°C) and 14.696 psia (1 atm). This is the common US industry standard (often called “SCF” in natural gas).
- The conversion is for volume only, not mass. To convert mass, you need the gas’s molecular weight and the ideal gas law.
- If your gas is not at standard conditions, the temperature and pressure corrections apply.
Why Standard Conditions Matter
Gases expand and contract with temperature and pressure. A liter of gas at 100°C contains far fewer molecules than a liter at 0°C. Standard cubic feet (scf) provides a consistent reference point so that volumes can be compared regardless of the actual conditions. In the natural gas industry, for example, contracts and measurements are often specified in scf at 60°F and 14.696 psia. Without a standard, a “cubic foot” of gas could mean different amounts of gas depending on the weather or altitude.
Other standard conditions exist. The International Union of Pure and Applied Chemistry (IUPAC) uses 0°C (273.15 K) and 100 kPa (0.9869 atm) for STP. Some European standards use 15°C (288.15 K) and 101.325 kPa. Always check which standard your application requires. The calculator above uses the US customary standard of 60°F and 14.696 psia, which is the most common for scf.
How to Use the Calculator
Enter the volume in liters, the actual temperature in °C, and the actual pressure in atm. If your pressure is given in other units, convert first:
- 1 atm = 101.325 kPa = 14.696 psi = 760 mmHg
- 1 bar = 0.98692 atm
The calculator automatically applies the temperature and pressure corrections. If your gas is already at standard conditions, set temperature to 15.6°C and pressure to 1 atm; the result will be the simple volume conversion.
For example, if you have 500 liters of gas at 25°C and 2 atm, the calculator will first adjust for pressure (2×) and temperature (288.15/298.15 ≈ 0.966), giving a result about 1.93 times the simple volume conversion.
Common Mistakes and Misconceptions
- Forgetting the temperature/pressure correction: Many people simply multiply liters by 0.0353147, ignoring that the gas is not at standard conditions. This can lead to significant errors, especially for gases stored under pressure or at extreme temperatures.
- Mixing up standard conditions: Using 0°C instead of 15.6°C changes the result by about 5.5%. Always confirm which standard your industry or application uses.
- Confusing scf with actual cubic feet (acf): scf is at standard conditions; acf is at actual conditions. The conversion between them is exactly the pressure and temperature ratios.
- Using the wrong conversion factor: 1 liter = 0.0353147 ft³ is exact. Some sources use 0.0353, which is fine for rough estimates but not for precise engineering.
When to Use This Conversion
This conversion is commonly needed in:
- Natural gas and fuel gas measurement: Gas meters often measure in cubic feet (at actual conditions), but billing may be in scf or therms.
- Industrial gas supply: When ordering cylinders of nitrogen, oxygen, or other gases, the volume is often stated in scf. Knowing the liters in a cylinder helps you estimate how many scf you have.
- Laboratory gas calculations: When using gas laws to determine volumes of gases produced or consumed in reactions, converting to scf can help compare with literature values.
- Environmental reporting: Emissions of gases are often reported in scf for consistency.
For example, a standard 9-inch diameter, 51-inch tall gas cylinder holds about 50 liters of liquid argon. When vaporized at standard conditions, that gives roughly 50 × 0.0353147 = 1.77 scf per liter of liquid, but because liquid argon expands about 860 times, the actual gas volume is much larger. This calculator is for gas volume, not liquid-to-gas expansion.
Limitations and Precision
The ideal gas law is accurate for most gases at low to moderate pressures and high temperatures. At high pressures (above ~10 atm) or low temperatures (near the boiling point), real gases deviate due to intermolecular forces and molecular volume. For such cases, use a real gas equation of state (like van der Waals or Peng-Robinson) or look up the compressibility factor (Z). The calculator assumes Z = 1.
Also, the conversion is only for volume. If you need to know the mass of gas, you must multiply the number of moles by the molecular weight. At standard conditions, one mole of ideal gas occupies 23.685 L (at 60°F, 1 atm) or 22.414 L (at 0°C, 1 atm). So 1 scf is equivalent to about 1.198 moles of gas.
Frequently Asked Questions
Q: What is the difference between scf and standard cubic meter (scm)?
A: Scm uses standard conditions of 0°C and 1 atm (or sometimes 15°C and 1 atm). One scf equals 0.0283168 scm (if both use the same standard temperature). Always check which standard is used for scm.
Q: How do I convert liters of liquid gas to scf?
A: You need the liquid density and the gas expansion ratio. For example, liquid nitrogen has a density of about 0.808 g/mL, and 1 liter of liquid nitrogen vaporizes to about 0.682 scf (at 60°F, 1 atm). This is not a simple volume conversion; you must use the gas law with the mass.
Q: Does the type of gas affect the conversion?
A: No, for ideal gases the volume conversion is the same. Real gas deviations are small at standard conditions. However, the mass of gas in a given scf depends on the molecular weight. For example, 1 scf of methane weighs about 0.0423 lb, while 1 scf of carbon dioxide weighs about 0.1155 lb.
Q: What if my pressure is in psig?
A: Psig (pounds per square inch gauge) measures pressure above atmospheric. To convert to absolute pressure, add atmospheric pressure (14.696 psi). For example, 100 psig = 114.696 psia. Then convert psia to atm by dividing by 14.696.
Q: Why are there different standard temperatures?
A: Different industries adopted different standards historically. The US natural gas industry uses 60°F, while many international standards use 15°C (59°F) or 0°C. Always confirm the standard used in your region or contract.
For laboratory work, always follow your lab method and safety data sheets (SDS) when handling gases. This calculator is for educational and planning purposes; verify critical measurements with calibrated instruments.
Related
Formula used
in l | Volume in liters | L | 100 | 0 in t | Gas temperature | °C | 15.6 | -273.15 in p | Gas pressure | atm | 1 | 0 out scf | Volume in standard cubic feet | scf | l * 0.0353147 * (p / 1) * (288.15 / (t + 273.15)) | 4 out m3 | Volume in cubic meters | m³ | l / 1000 | 4
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Volume Calculator in Chemistry: How to Use It0.2000 mol/L
- Volume Calculator in mm: Convert & Calculate100,000 mm³
- Volume Calculator Feet and Inches: How to Use It3.12 ft³
- Volume Calculator: Convert ft to Yards1.00 yd³
- Surfboard Volume Calculator JS: How It Works32.4 L
- Volume Calculator cm to Litres: How to Convert2.500 L