molecalculator

Moles & Molar Mass

How to Find the Continuous Decay Rate

Calculator No. 01-7066 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This guide explains how to find the continuous decay rate (often denoted as k) for a quantity that decreases exponentially over time. You’ll learn the formula, see a step-by-step example, and get a calculator to check your work. You’ll need a scientific calculator or this page’s built-in calculator, and the values for the initial amount, the amount remaining, and the elapsed time.

Formula

The continuous decay model is:

N(t) = N₀ · e−kt

Where:

  • N(t) = the amount remaining after time t (same unit as N₀)
  • N₀ = the initial amount (any unit)
  • e = Euler’s number, approximately 2.71828
  • k = the continuous decay rate (per unit time, e.g., per second, per year)
  • t = the elapsed time (in the same time unit as k)

To solve for k, rearrange:

k = ln(N₀ / N(t)) / t

Here, ln is the natural logarithm (log base e). The units of k are the reciprocal of the time unit (e.g., 1/year, per hour).

Worked Example

Using the calculator defaults: N₀ = 100, N(t) = 25, t = 10.

Step 1: Compute the ratio N₀ / N(t):

100 / 25 = 4

Step 2: Take the natural logarithm of the ratio:

ln(4) ≈ 1.38629436112

Step 3: Divide by the time t:

k = 1.38629436112 / 10 = 0.138629436112

Rounded to 4 decimal places: k ≈ 0.1386 per time unit.

The calculator also gives the half-life: ln(2) / k ≈ 0.6931 / 0.1386 ≈ 5.0000 time units. This makes sense: if 100 decays to 25 in 10 time units, that’s two half-lives (100 → 50 → 25), so each half-life is 5 time units.

Assumptions

  • The decay is exponential and continuous (the rate is proportional to the amount present).
  • The decay rate k is constant over the time interval.
  • The initial amount N₀ is positive and the remaining amount N(t) is less than N₀ (for decay).
  • Time is measured in consistent units (e.g., all in hours, all in years).

When to Use This

Use the continuous decay rate when you have data points (initial amount, final amount, and time) and you want to characterize how fast something shrinks. It’s common in:

  • Radioactive decay (though half-life is more common there)
  • Drug elimination from the body (pharmacokinetics)
  • Population decline (if modeled continuously)
  • Cooling (Newton’s law of cooling)
  • Discharging capacitors in electronics

The result k tells you the fraction of the remaining amount that disappears per unit time. For example, k = 0.1386 per year means that at any instant, about 13.86% of the current amount decays per year (continuously, not annually).

Common Mistakes

  • Using the wrong logarithm: The formula requires the natural logarithm (ln), not log base 10. On many calculators, the log button is base 10; make sure you use ln.
  • Mixing up N₀ and N(t): The ratio must be initial over remaining, not the other way around. If you invert, you’ll get a negative k (which would indicate growth).
  • Ignoring units: If time is in minutes and you want k per hour, you must convert time to hours first, or convert k afterward. The calculator assumes the time unit you enter matches the unit of k you want.
  • Rounding too early: If you round ln(4) to 1.39 and then divide by 10, you get 0.139, which is slightly off. Keep as many digits as possible until the final step.
  • Confusing continuous rate with annual/periodic rate: Continuous decay rate is not the same as a simple percentage decrease per period. For example, a 10% annual decrease (simple) gives a continuous rate of about 0.1054 per year, not 0.10.

Tips

  • If you know the half-life (t½), you can find k directly: k = ln(2) / t½. This is a handy shortcut.
  • Always check that your k is positive for decay. If you get a negative number, you likely swapped N₀ and N(t).
  • Use consistent units: if your time is in days, your k will be per day. To convert to per hour, divide k by 24 (since there are 24 hours per day).
  • When using the calculator, you can leave the units blank (the “-” option) as long as you use the same unit for N₀ and N(t). The calculator only cares about the ratio.
  • For very small or very large times, scientific notation is fine; the calculator handles it.

Troubleshooting

My result is negative. Check that N₀ > N(t). If N(t) is larger, you’re actually looking at growth, not decay. Swap the values or use the growth formula instead.

My result seems too large or too small. Verify the time unit. If you entered time in seconds but expected k per year, the number will be huge. Convert time to the desired unit first (e.g., seconds to years: divide by 31,557,600).

The calculator says “Cannot compute” or shows an error. This happens if N₀ or N(t) is zero or negative, or if t is zero. Ensure all inputs are positive and t > 0. Also, N(t) must be less than N₀ for decay.

I get a different answer from a textbook. Check if the textbook uses a different base (e.g., base 2) or defines the decay constant differently. Some sources use λ for decay constant, but the math is identical. Also, check if they use discrete compounding (e.g., annual) instead of continuous.

My data has multiple time points. If you have several (t, N(t)) pairs, you can fit an exponential curve to find the best k. The simple two-point formula will give a k that may not be the best fit; use regression for more accurate results.

Frequently Asked Questions

What is the difference between continuous decay rate and half-life?

The continuous decay rate (k) tells you how quickly the quantity shrinks at any instant, while half-life (t½) is the time it takes to reduce to half. They are related by t½ = ln(2)/k. Both describe the same process, just from different angles.

Can I use this for growth instead of decay?

Yes, but you’d use the formula N(t) = N₀·e^(kt) and solve k = ln(N(t)/N₀)/t. The calculator here is set up for decay (N₀ > N(t)), so for growth, swap the amounts or take the absolute value of k.

What if I only have the percentage decrease over a period?

If you know that a quantity decreases by, say, 20% per year (so N(t) = 0.8·N₀ after 1 year), you can plug in N₀ = 1, N(t) = 0.8, t = 1 year to get k = ln(1/0.8) ≈ 0.2231 per year. This is the continuous rate equivalent to a 20% annual decrease.

Why use natural log instead of log base 10?

Because the exponential model uses base e. The natural log is the inverse of the exponential function, so it directly solves for the exponent. Using log base 10 would require converting bases, which is extra work and prone to error.

Does the continuous decay rate depend on the initial amount?

No. The continuous decay rate is a property of the process, not the starting amount. If you double N₀, the time to decay to half is the same, and k remains the same. That’s why the formula uses a ratio, not absolute differences.

Can I use this for financial depreciation?

Yes, if an asset depreciates continuously at a constant rate, you can model its value with the same formula. For example, a car losing 15% of its value per year continuously would have k ≈ 0.1625 per year. Just ensure the value never reaches zero (exponential decay approaches zero asymptotically).

Related

Formula used
in N0 | Initial amount | - | 100 | 0.0001
in Nt | Amount after time t | - | 25 | 0.0001
in t | Time elapsed | - | 10 | 0.0001
out k | Continuous decay rate | per time unit | ln(N0 / Nt) / t | 4
out hl | Half-life | time units | ln(2) / k | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →