molecalculator

Moles & Molar Mass

How to Solve for Decay Constant (λ)

Calculator No. 01-7109 · Updated · Formula and assumptions shown below

Decay constant (λ) 0.000121 s⁻¹
λ from N(t) and t
0.000223 s⁻¹
Result, rounded to 6 decimal places
Check: half-life from λ
5,730.00 s
Result, rounded to 2 decimal places
Half-life (t₁/₂)
5730 s
Set in the form below
You enter
Half-life (t₁/₂) (s), Elapsed time (s), Initial amount (N₀), Remaining amount (N(t))
You get
Decay constant (λ) (s⁻¹), λ from N(t) and t (s⁻¹), Check: half-life from λ (s)
Rounding
6 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This guide shows you how to solve for the decay constant (λ) in exponential decay processes, whether you’re working with radioactive half-lives, drug clearance, or capacitor discharge. You’ll learn the core formulas, how to rearrange them, and how to calculate λ from half-life, from activity measurements, or from a time-series of remaining quantity. We’ll also cover common unit pitfalls and how to check your answer.

Formula

The decay constant λ (lambda) appears in the exponential decay law:

N(t) = N₀ · e−λt

Where:

  • N(t) = amount remaining after time t (same unit as N₀)
  • N₀ = initial amount (any unit, as long as consistent)
  • λ = decay constant (unit: s⁻¹, min⁻¹, yr⁻¹, etc.)
  • t = elapsed time (unit matching λ)

To solve for λ directly, take the natural logarithm of both sides:

λ = ln(N₀ / N(t)) / t

If you know the half-life (t₁/₂), use:

λ = ln(2) / t₁/₂

Here, ln(2) ≈ 0.693147. Both formulas give the same λ for the same process.

Worked Example

Using the calculator defaults: carbon-14 has a half-life of 5730 years. After 1000 years, a sample that started at 100 units has 80 units remaining. Let’s find λ.

Step 1: From half-life

λ = ln(2) / 5730 yr = 0.693147 / 5730 = 1.2097 × 10⁻⁴ yr⁻¹

Step 2: From the amount ratio

λ = ln(100 / 80) / 1000 yr = ln(1.25) / 1000 = 0.22314 / 1000 = 2.2314 × 10⁻⁴ yr⁻¹

Wait – these don’t match! That’s because the defaults are not consistent: a sample that decays from 100 to 80 in 1000 years has a shorter half-life than 5730 years. The calculator shows both values separately, so you can compare. For a real problem, you would use one method or the other, or check that your data matches the half-life.

To see a consistent example, suppose you measure that a sample drops from 100 to 50 in 5730 years. Then:

λ = ln(100 / 50) / 5730 = ln(2) / 5730 = 1.2097 × 10⁻⁴ yr⁻¹

This matches the half-life method exactly.

Assumptions

  • The decay follows first-order kinetics: the rate is proportional to the amount present.
  • The decay constant λ is constant over time (no changing conditions).
  • For radioactive decay, the sample is not gaining or losing atoms except by decay.
  • Time units are consistent: if half-life is in years, use years for t.

When to Use Each Formula

Use λ = ln(2) / t₁/₂ when you know the half-life – this is common for radioactive isotopes, where half-lives are tabulated. Use λ = ln(N₀ / N(t)) / t when you have two measurements of the amount at different times – for example, a lab experiment where you measure activity at t=0 and at a later time.

The decay constant is also related to the mean lifetime τ by τ = 1/λ, and to the half-life by t₁/₂ = ln(2)/λ. Knowing λ lets you predict the amount at any future time using N(t) = N₀ e−λt.

Common Mistakes

  • Unit mismatch: Mixing seconds and years without converting. Always convert time to the same unit as the half-life.
  • Using log base 10 instead of natural log: The formula requires ln (natural log), not log₁₀. Using log₁₀ will give a wrong answer by a factor of about 2.303.
  • Swapping N₀ and N(t): The ratio must be initial over remaining. If you flip it, you get a negative λ.
  • Forgetting that λ has units: λ is not dimensionless; it is per time (s⁻¹, yr⁻¹). Always include the unit.
  • Rounding too early: Rounding ln(2) to 0.693 is fine, but don’t round intermediate results to 2 significant figures before the final answer.

Tips

  • Always write down the units for every value. If your half-life is in hours, your λ will be in h⁻¹.
  • Use the calculator’s first output (λ from half-life) as a quick check. If your measured data gives a very different λ, your data or assumptions are off.
  • When using the ratio formula, make sure N₀ and N(t) are in the same unit (e.g., both in grams, both in counts per minute). The ratio is unitless.
  • For radioactive decay, activity (decays per second) is proportional to the number of atoms, so you can use activity values directly in place of N₀ and N(t).
  • Remember that λ is positive. If you get a negative value, check your ratio.

Troubleshooting

My λ from half-life and λ from data don’t match. This usually means your data doesn’t follow the half-life you assumed. Re-check your measurements or the half-life value. It could also be a unit error: e.g., you used a half-life in years but time in days.

I get a negative λ. You likely swapped N₀ and N(t). The initial amount must be larger than the remaining amount. If N(t) > N₀, you’re describing growth, not decay.

My calculator shows “Cannot compute”. This happens when the ratio N₀/N(t) is less than 1 (i.e., N(t) > N₀). Check your inputs – the remaining amount cannot exceed the initial amount in a decay process.

I’m unsure about units for λ. λ is always per time unit. If t is in seconds, λ is in s⁻¹. If t is in years, λ is in yr⁻¹. Convert everything to the same time base before calculating.

Frequently Asked Questions

What is the decay constant in simple terms?

The decay constant λ is the probability per unit time that a single atom (or entity) will decay. A larger λ means faster decay.

How do I convert half-life to decay constant?

Use λ = ln(2) / t₁/₂. For example, if t₁/₂ = 10 s, then λ = 0.693 / 10 = 0.0693 s⁻¹.

Can I use the decay constant for growth processes?

No, decay uses a negative exponent. For growth (like population increase), you’d use a positive exponent: N(t) = N₀ e+kt, where k is a growth constant.

What is the relationship between decay constant and mean lifetime?

The mean lifetime τ is the average time an atom survives before decaying. It equals 1/λ. So if λ = 0.1 s⁻¹, the mean lifetime is 10 s.

Does the decay constant change with temperature or pressure?

For radioactive decay, λ is essentially constant regardless of temperature, pressure, or chemical state. For other exponential decays (like chemical reactions), λ can depend on temperature – that’s described by the Arrhenius equation.

Why do we use natural log instead of log base 10?

Because the exponential function ex is the inverse of the natural log. The decay law is derived from calculus where e is the natural base. Using log₁₀ would require a conversion factor.

Related

Formula used
in t12 | Half-life (t₁/₂) | s | 5730 | 0
in t | Elapsed time | s | 1000 | 0
in n0 | Initial amount (N₀) | - | 100 | 0
in nt | Remaining amount (N(t)) | - | 80 | 0
out lam | Decay constant (λ) | s⁻¹ | ln(2) / t12 | 6
out lam2 | λ from N(t) and t | s⁻¹ | ln(n0 / nt) / t | 6
out half | Check: half-life from λ | s | ln(2) / lam | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →