This calculator works out the change in inner diameter (dilation) of a thick-walled cylinder when it is subjected to internal pressure. You enter the cylinder’s original inner radius, wall thickness, the internal pressure, and the material’s elastic modulus and Poisson’s ratio, and you get back the radial expansion of the inner surface in millimeters.
Formula
The radial displacement at the inner surface of a thick-walled cylinder under internal pressure only (no external pressure) is given by the Lamé solution:
δ = (p · ri² / (E · (ro² − ri²))) · [(1 − ν) · ri + (1 + ν) · ro² / ri]
where:
- δ = radial dilation (change in inner radius) in mm
- p = internal gauge pressure in MPa (1 MPa = 1 N/mm²)
- ri = inner radius in mm
- ro = outer radius in mm (= ri + wall thickness)
- E = Young’s modulus (elastic modulus) in MPa (1 GPa = 1000 MPa)
- ν = Poisson’s ratio (dimensionless, typically 0.25–0.35 for metals)
The calculator uses the same formula with ro replaced by (r + t). Note that the dilation is directly proportional to pressure and inversely proportional to the elastic modulus—stiffer materials dilate less.
Worked Example
Take a steel cylinder with inner radius 50 mm, wall thickness 10 mm, internal pressure 20 MPa, elastic modulus 200 GPa, and Poisson’s ratio 0.3.
- Outer radius ro = 50 + 10 = 60 mm
- ro² − ri² = 60² − 50² = 3600 − 2500 = 1100 mm²
- E in MPa = 200 GPa × 1000 = 200,000 MPa
- First bracket: (p · ri²) / (E · (ro² − ri²)) = (20 × 2500) / (200000 × 1100) = 50000 / 220000000 = 0.00022727
- Second bracket: (1 − 0.3)·50 + (1 + 0.3)·60²/50 = 0.7·50 + 1.3·3600/50 = 35 + 93.6 = 128.6
- δ = 0.00022727 × 128.6 = 0.02922 mm (rounded to 0.0292 mm)
So the inner radius increases by about 0.029 mm—roughly 0.06% of the original radius. The calculator’s default output matches this value.
Assumptions
- The cylinder is thick-walled (wall thickness ≥ 10% of inner radius) and the Lamé solution applies.
- Material is homogeneous, isotropic, and linearly elastic (Hooke’s law holds).
- Only internal pressure acts; external pressure is zero.
- The cylinder is long (plane strain conditions) or the ends are free (plane stress); the formula gives the same radial displacement for both in this simple case.
- Deformations are small—the change in radius is much smaller than the original radius.
When to Use This Calculator
Engineers use this calculation for pressure vessels, hydraulic cylinders, pipe walls, and any thick-walled tube under internal pressure. It helps predict how much the bore expands when pressurized, which matters for sealing, interference fits, and maintaining clearance in moving parts. For example, if you have a hydraulic cylinder with a 100 mm bore and a 10 mm wall, a 20 MPa working pressure will enlarge the bore by roughly 0.03 mm—enough to affect a precision piston seal clearance.
The calculator is also useful for estimating stress indirectly: the dilation is proportional to the hoop stress at the inner surface, so a larger dilation indicates higher stress for a given material.
How to Choose Input Values
- Inner radius and wall thickness: Measure the actual geometry. Use consistent units (mm). If you have outer diameter and wall thickness, inner radius = (outer diameter/2) − wall thickness.
- Internal pressure: Use the gauge pressure (relative to atmosphere) in MPa. 1 MPa ≈ 145 psi. If pressure is given in bar, divide by 10 to get MPa.
- Elastic modulus: Look up the material’s Young’s modulus. Common values: steel 200 GPa, aluminum 69 GPa, titanium 116 GPa, brass 100 GPa. Convert GPa to MPa by multiplying by 1000 (the calculator does this for you).
- Poisson’s ratio: Typical values: metals 0.27–0.35, rubber ~0.5, concrete ~0.2. Use the material’s datasheet value.
Common Mistakes and Misconceptions
A frequent error is using the thin-wall formula (δ = p·r²/(E·t)) for thick cylinders. That formula assumes uniform stress across the wall, which is only valid when t < r/10. The Lamé solution used here is exact for thick walls and reduces to the thin-wall approximation when t is small.
Another mistake is mixing units: if pressure is in psi and radius in inches, the result will be in inches, but the elastic modulus must be in psi. Always convert to a consistent unit system. The calculator uses mm and MPa, so if you have inches, multiply by 25.4 to get mm, and convert psi to MPa (1 psi ≈ 0.00689476 MPa).
Some users confuse radial dilation with hoop strain. Hoop strain is the relative change in circumference (εθ = δ/r), while dilation is the absolute change in radius. The calculator gives the absolute value.
Limitations of the Formula
The Lamé solution assumes the material stays elastic. If the pressure is high enough to cause yielding (when the von Mises stress exceeds the yield strength), the dilation will be larger than predicted and permanent deformation occurs. For high-pressure design, check the stress separately. Also, the formula assumes a perfectly cylindrical shape and uniform wall thickness; real cylinders with weld seams, corrosion, or ovality will behave differently.
Temperature effects are not included. If the cylinder operates at elevated temperatures, the elastic modulus decreases and thermal expansion adds to the dilation. For cryogenic or high-temperature service, adjust E accordingly and add thermal expansion separately.
Frequently Asked Questions
Is this the same as pipe expansion under pressure?
Yes, for a straight pipe, the radial dilation is the same as for a cylinder. However, pipes often have fittings and bends that complicate the stress state, so this calculation gives the local bore expansion for a straight section.
What if the cylinder has external pressure too?
Then you need the full Lamé equation with both pressures. The formula becomes more complex, and the dilation could be negative (contraction). This calculator assumes zero external pressure, which is typical for internal pressure vessels.
How do I convert the dilation to a change in inner diameter?
Simply multiply the radial dilation by 2. The inner diameter change = 2δ. For the worked example, the diameter increases by 0.0584 mm.
Does the cylinder length affect the dilation?
In the simple Lamé solution, length does not appear because the radial displacement is independent of axial position (for a long cylinder away from ends). End effects are neglected, which is fine for most design calculations.
What is a typical dilation for a hydraulic cylinder?
For a steel cylinder with a 100 mm bore, 10 mm wall, at 20 MPa, the dilation is about 0.03 mm. This is small but can be significant for tight clearances. Always check manufacturer tolerances.
Can I use this for a thick-walled pressure vessel with a closed end?
Yes, the radial dilation is the same as for an open-ended cylinder under internal pressure. The axial stress differs, but it does not affect the radial displacement in the linear elastic solution.
Related
Formula used
in r | Inner radius | mm | 50 | 0.1 | 10000 in t | Wall thickness | mm | 10 | 0.1 | 10000 in p | Internal pressure | MPa | 20 | 0 | 1000 in E | Elastic modulus | GPa | 200 | 0.1 | 1000 in nu | Poisson's ratio | - | 0.3 | 0 | 0.5 out delta | Radial dilation of inner surface | mm | p * r^2 / (E * (r + t)^2 - E * r^2) * ((1 - nu) * r + (1 + nu) * (r + t)) | 4
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Calcium Nitrate Boiling Point
- Cation Formula for Magnesium Nitrate0.0788 mol/L
- Potassium Nitrate Solubility in Water: Full Data25.9 g/100 mL
- Greenhouse Grade Potassium Nitrate: Uses & Rates0.2000 mol/L
- Molar Mass of KNO2: Formula & Calculation0.1373 mol/L
- Potassium Nitride Formula & How to Write It