molecalculator

Moles & Molar Mass

Magnesium Sulfate Density Calculator and Values

Calculator No. 01-6627 · Updated · Formula and assumptions shown below

Density 2.3981 g/cm³
Density
2,398 kg/m³
= Density × 1000
Sample mass
10 g
Set in the form below
Sample volume
4.17 cm³
Set in the form below
You enter
Sample mass (g), Sample volume (cm³)
You get
Density (g/cm³), Density (kg/m³)
Rounding
4 dp · 0 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Magnesium sulfate does not have one density value: it depends chiefly on whether the material is anhydrous MgSO₄ or a hydrated crystal such as Epsom salt (MgSO₄·7H₂O). This calculator estimates the density of a solid from its mass and volume; enter those measurements in grams and cubic centimetres to get density in g/cm³ and kg/m³.

Formula

Density is mass divided by volume: ρ = m / V. In the calculator, m is sample mass in grams (g), V is sample volume in cubic centimetres (cm³), and ρ is density in grams per cubic centimetre (g/cm³). The second result converts that value to kilograms per cubic metre: 1 g/cm³ = 1000 kg/m³, so ρkg/m³ = ρ × 1000.

The formula describes the measured density of the sample, not a universal constant for every form or batch of magnesium sulfate. The volume must refer to the same material whose mass is measured, and should be a solid’s bulk volume if the aim is to compare with tabulated crystal densities.

Worked Example

Using the defaults, the sample has a mass of 10 g and a volume of 4.17 cm³.

  1. Density: ρ = 10 g / 4.17 cm³ = 2.3980815 g/cm³, which displays as 2.3981 g/cm³.
  2. Convert to SI units: 2.3980815 × 1000 = 2398.0815 kg/m³, which displays as 2398 kg/m³.

Assumptions

  • The mass and volume refer to the same sample and are measured consistently.
  • The sample is treated as a solid with a defined external volume; the calculator does not correct for pores, trapped air, or impurities.
  • The result is a measured value, not an assertion that all magnesium sulfate has the same density.

Typical Magnesium Sulfate Densities

Reference values depend on the chemical form and conditions. Anhydrous magnesium sulfate is commonly listed with a crystal density near 2.66 g/cm³. Magnesium sulfate heptahydrate, the crystalline form commonly called Epsom salt, is commonly listed near 1.68 g/cm³. These are approximate reference values, not interchangeable values for every sample.

The difference is not a contradiction. In the heptahydrate, each formula unit includes seven water molecules in the crystal structure. This changes both mass and the dimensions and packing of the crystal lattice. A value for anhydrous MgSO₄ should therefore not be applied automatically to Epsom salt, and a hydrate’s density cannot be inferred just by adding the mass of water to the anhydrous value.

Temperature, crystal structure, purity, and how the sample is packed or measured can also affect a practical result. A handbook’s crystal density describes a defined solid phase; a container filled with granules has a bulk density that includes gaps between particles and is usually lower.

Crystal Density Versus Bulk Density

“Density” can refer to distinct measurements. Crystal or true density concerns the solid material itself, excluding spaces between particles. Bulk density is the mass of a loose powder or granules divided by the volume occupied by the material together with its interparticle voids. It changes when particles settle or are packed differently.

For example, weighing a scoop of Epsom salt and dividing by the scoop’s capacity gives an approximate bulk density, not the crystal density of MgSO₄·7H₂O. The same mass can occupy a different container volume after settling. To compare a result with a reference value such as 1.68 g/cm³, use a method that measures the solid’s volume rather than simply the volume of a pile of crystals.

For a liquid solution, there is another meaning: solution density is the mass of the entire solution divided by its volume. It is not the density of magnesium sulfate alone. Concentration, temperature, and dissolved components affect solution density, so a solid reference value does not determine the density of a magnesium sulfate solution.

How to Measure and Interpret It

For a regular solid, measure its dimensions and calculate its volume using the appropriate geometric formula. For an irregular solid that does not dissolve or react with the chosen displacement liquid, volume may be estimated by liquid displacement. The calculator itself only performs mass divided by volume; it cannot tell whether the selected measurement method is appropriate.

  • Use grams for mass and cubic centimetres for volume. One millilitre equals 1 cm³.
  • Measure the sample’s volume, not the container capacity or the volume of liquid used to cover it.
  • Keep units consistent. If volume is entered in mL, its numeric value is the same as cm³.
  • Retain sensible precision: a result with many calculator digits is not more accurate than the balance and volume measurement.

A result well below a crystal reference value may indicate void spaces in a packed sample or an incorrect volume basis. A result above the reference can point to a unit conversion error, an unsuitable measurement method, or a different composition. These possibilities are clues, not proof of a particular cause.

Common Confusions and Limits

A frequent misconception is that “magnesium sulfate density” names one fixed number. It does not: hydration state and the meaning of the measurement matter. Always identify the form—anhydrous MgSO₄, a specified hydrate, loose crystals, or solution—when reporting a density.

This calculator does not identify a sample, determine its hydration state, or correct for temperature or porosity. It also does not calculate concentration or solubility. For a solution, measure the total solution mass and its final volume to obtain solution density; that answer still does not state how much magnesium sulfate is dissolved. Where bench work is involved, follow your lab method, the safety data sheet (SDS), and your supervisor.

Frequently Asked Questions

What is the density of anhydrous magnesium sulfate?
Anhydrous magnesium sulfate is commonly reported at about 2.66 g/cm³ as a crystal-density reference. Check the source’s stated conditions and material form when precision matters.

What is the density of Epsom salt?
Epsom salt is magnesium sulfate heptahydrate, MgSO₄·7H₂O. Its crystal density is commonly listed near 1.68 g/cm³; loose granules have a lower, packing-dependent bulk density.

Is magnesium sulfate denser than water?
Both common crystal forms have reference densities greater than liquid water near room temperature, whose density is about 1 g/cm³. This comparison does not mean a pile of crystals will behave like a solid block in water.

Does magnesium sulfate solution have the same density as the crystals?
No. A solution’s density belongs to the entire mixture and varies with concentration and temperature. The crystal density of a solid cannot be used as the solution density.

How do I convert magnesium sulfate density to kg/m³?
Multiply a value in g/cm³ by 1000. For example, 1.68 g/cm³ equals 1680 kg/m³.

Related

Formula used
in m | Sample mass | g | 10 | 0
in v | Sample volume | cm³ | 4.17 | 0
out d | Density | g/cm³ | m / v | 4
out dk | Density | kg/m³ | d * 1000 | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →