molecalculator

Moles & Molar Mass

Percent Solution Dilution Calculator and Formula

Calculator No. 01-6037 · Updated · Formula and assumptions shown below

Starting solution required 20.00 mL
Diluent required
80.00 mL
= Final solution volume − Starting solution required
Starting concentration
10 %
Set in the form below
Target concentration
2 %
Set in the form below
You enter
Starting concentration (%), Target concentration (%), Final solution volume (mL)
You get
Starting solution required (mL), Diluent required (mL)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A percent solution dilution calculator finds how much of a more concentrated solution and how much diluent are needed to make a target volume at a lower percent concentration. Enter the starting concentration, target concentration, and final volume to get the stock volume and the diluent volume.

Formula

The calculator uses the dilution relationship CsVs = CtVf. Solving for the volume of starting solution gives Vs = Vf × Ct / Cs. The diluent estimate is Vd = Vf − Vs.

  • Cs is the starting solution concentration, in percent.
  • Ct is the target concentration, in percent.
  • Vf is the intended final solution volume, in mL.
  • Vs is the volume of starting solution, in mL.
  • Vd is the calculated diluent volume, in mL.

The percent units cancel in the ratio Ct/Cs, so any consistent percent convention can be used for both concentrations. The calculator assumes the starting and target percentages use the same basis, such as both percent by volume (% v/v) or both percent by mass (% w/w). It does not convert between these types.

Worked Example

Using the default inputs, dilute a 10% starting solution to make 100 mL of a 2% target solution:

  1. Starting solution volume: Vs = 100 mL × 2% / 10% = 20.00 mL.
  2. Diluent estimate: Vd = 100 mL − 20.00 mL = 80.00 mL.

The result means to use 20.00 mL of starting solution and add diluent until the total solution volume is 100 mL. It does not necessarily mean to measure exactly 80 mL of diluent and combine the two; mixing can change the total volume.

Assumptions

  • The starting and target percentages describe the same kind of concentration.
  • The starting solution is sufficiently uniform, and dilution does not cause a chemical reaction or loss of solute.
  • The specified final volume is the volume of the complete solution, not the volume of solvent added.
  • The simple volume subtraction is an estimate; the exact diluent addition may differ if volumes change on mixing.

How Percent Dilution Works

Dilution lowers concentration by distributing a fixed amount of solute through a larger total volume. In the ideal calculation, the amount of solute carried in the measured starting portion is the amount present in the final solution. The equation CsVs = CtVf expresses that conservation.

For example, a target concentration half as strong as the starting solution requires the starting solution to make up half of the final volume. A target one-fifth as strong requires one-fifth of the final volume to be starting solution. This proportional relationship is why the calculator can handle many percent values without converting them into fractions first.

Percent notation alone does not identify what is being measured. Common forms include % w/v (grams of solute per 100 mL of final solution), % v/v (mL of liquid component per 100 mL of final solution), and % w/w (grams per 100 g of solution). Keep the convention consistent throughout the calculation and when reading the label or protocol.

When to Use This Calculator

Use the calculator for ordinary dilution arithmetic when you know the starting concentration and need a lower target concentration at a chosen final volume. It can help check a planned dilution or calculate the stock portion for a solution-preparation exercise. It is not suitable when the target is more concentrated than the starting material, when concentrations are on different bases, or when a method requires a more specific preparation calculation.

For reliable preparation, treat the output as a volume calculation, not a complete protocol. Check that the starting solution concentration is stated on the same basis as the target, and that your intended final volume is practical to measure. Where bench work is implied, follow your lab method, the safety data sheet (SDS) and your supervisor.

Reading Results and Common Mistakes

  • Mixing up final volume and diluent volume: the requested volume is the total volume after mixing. Add starting solution, then bring the mixture to the final volume when the method calls for that approach.
  • Combining unlike percentage bases: a 10% w/v solution and a 2% v/v target cannot be used in this ratio as though they were the same unit.
  • Trying to concentrate by dilution: if the target percentage is higher than the starting percentage, the calculated starting-solution volume exceeds the final volume. This does not describe a feasible dilution; use a more concentrated starting material or a separately validated concentration method.
  • Rounding too early: keep extra digits during intermediate calculations and round the measured volumes to suit the method and available equipment. The displayed hundredths are arithmetic precision, not a promise of measurement accuracy.
  • Assuming volumes always add exactly: the sum of component volumes may not equal the final mixed volume. For a defined final volume, use the preparation method’s instruction to make up to that volume rather than relying only on subtraction.

If the starting concentration is zero, there is no solute to dilute; the required stock-volume calculation is undefined. A target of zero gives a calculated stock volume of zero, though the appropriateness of that result depends on the purpose of the preparation.

Accuracy and Limits

This is a proportional arithmetic tool, not a measurement of concentration. Its answer depends on the stated values being correct and on the solution remaining homogeneous. If the stock label gives a range, uncertainty, density-based percentage, or a concentration expressed in different units, resolve those details before using the result.

Mass-based and volume-based percentages can require additional information to convert. For example, converting % w/w to % w/v generally requires solution density and a clear definition of the concentration basis. The calculator does not assume a density or infer the percentage convention from a number.

Frequently Asked Questions

What is the formula for diluting a percent solution?
Use CsVs = CtVf. Rearranged, the starting volume is Vs = Vf × Ct / Cs.

How do I dilute 10% to 2%?
The target is one-fifth of the starting concentration, so use one part of the 10% solution in five parts of final solution. For a 100 mL final volume, that is 20 mL of starting solution, brought to 100 mL total.

Do I add the calculated diluent volume to the stock?
The subtraction gives an estimated diluent volume. If the procedure specifies a final volume, add the starting solution and bring the mixture to that total volume; component volumes may not add exactly after mixing.

Can I use this for % w/v, % v/v, and % w/w?
Yes, if the starting and target concentrations use the same percentage basis. The equation does not convert between mass and volume bases.

Can dilution make a solution stronger?
No. If the target concentration exceeds the starting concentration, the calculated stock volume is larger than the desired final volume. A higher-concentration starting material is needed for a feasible dilution.

Related

Formula used
in cs | Starting concentration | % | 10 | 0 | 100
in ct | Target concentration | % | 2 | 0 | 100
in vf | Final solution volume | mL | 100 | 0
out vs | Starting solution required | mL | vf * ct / cs | 2
out vd | Diluent required | mL | vf - vs | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →