molecalculator

Moles & Molar Mass

Dilution Calculator for Physiology Lab Solutions

Calculator No. 01-6038 · Updated · Formula and assumptions shown below

Stock solution required 10.00 mL
Diluent required
90.00 mL
= Final solution volume − Stock solution required
Stock concentration
100 mmol/L
Set in the form below
Target concentration
10 mmol/L
Set in the form below
You enter
Stock concentration (mmol/L), Target concentration (mmol/L), Final solution volume (mL)
You get
Stock solution required (mL), Diluent required (mL)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A physiology lab dilution calculator determines the volume of a concentrated stock solution needed to prepare a target concentration and final volume. Enter the stock concentration, desired final concentration, and final volume; it returns the stock volume and the amount of diluent to add.

Formula

The calculator uses the dilution relationship C₁V₁ = C₂V₂. Solving for the volume of stock gives V₁ = C₂V₂ / C₁. The diluent volume is calculated as V₂ − V₁.

  • C₁ is the stock concentration, in mmol/L.
  • V₁ is the stock volume required, in mL.
  • C₂ is the target concentration, in mmol/L.
  • V₂ is the final solution volume, in mL.
  • V₂ − V₁ is the approximate volume of diluent to add, in mL.

The concentration units must match. Because both volumes in the equation use mL, no volume conversion is needed. This is equivalent to converting both volumes to liters before applying the relationship: the same volume units cancel on both sides.

Worked Example

Using the calculator defaults—100 mmol/L stock, a 10 mmol/L target, and a 100 mL final volume:

  1. Calculate the stock volume: V₁ = (10 mmol/L × 100 mL) / (100 mmol/L) = 10 mL.
  2. Calculate the diluent volume: 100 mL − 10 mL = 90 mL.

The calculator therefore gives 10.00 mL of stock solution and 90.00 mL of diluent. In practice, bring the mixture to the specified final volume according to your lab method; adding a nominal diluent volume may not produce precisely that final volume in every solution.

Assumptions

  • The stock and target concentrations use the same concentration units and refer to the same solute.
  • The target concentration is no greater than the stock concentration, so this is a dilution rather than a concentration step.
  • The final volume means the total solution volume, not the volume of solvent alone.
  • The calculation assumes the solute amount is conserved and does not account for reaction, degradation, precipitation, or volume changes that matter to a particular method.

How to Use a Dilution Calculator in a Physiology Lab

Physiology experiments often compare responses under defined solution conditions. A dilution calculation can help plan working solutions from a known stock—for example, a salt, buffer component, or other assay reagent—provided the lab protocol specifies the required composition and the materials are appropriate for the work. The arithmetic answers how much stock corresponds to a chosen target concentration and final volume; it does not decide whether that concentration or formulation is scientifically suitable.

To use the calculator:

  1. Read the stock concentration and its units from the solution label or preparation record.
  2. Enter the target concentration and the intended final volume from the experiment’s validated method.
  3. Check that the stock concentration is at least as high as the target concentration.
  4. Use the calculated stock volume as a planning value, then prepare and verify the solution using the laboratory’s prescribed method.

For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.

Choosing Units and Interpreting the Result

Concentration units can be molar (mol/L), millimolar (mmol/L or mM), or another compatible unit. The calculator accepts mmol/L for both concentration fields. If a protocol gives mol/L, convert it before entry: 1 mol/L = 1,000 mmol/L. For instance, 0.025 mol/L is 25 mmol/L. Do not enter a value in mol/L while labeling or treating it as mmol/L; that creates a thousand-fold error.

The first result is the required volume of stock. The second is a simple volume difference that estimates the diluent to add. This subtraction is useful for planning, but “add 90 mL” and “make up to 100 mL final volume” are not always operationally interchangeable. Solute and solvent volumes may not be perfectly additive, and some protocols specify a volumetric vessel or a particular mixing sequence. Use the final-volume instruction in the method as the controlling requirement.

Common Mistakes and Limits

  • Confusing stock and target concentrations: C₁ is the more concentrated starting solution; C₂ is the intended weaker solution.
  • Using the wrong final volume: V₂ is the final total solution volume, not the amount of diluent to pour in.
  • Mixing unit scales: Convert mol/L to mmol/L or vice versa before calculating.
  • Rounding too early: Keep useful digits during planning, then round only to a precision the available lab equipment and method support.
  • Assuming the calculator validates a protocol: It checks dilution arithmetic only. It cannot verify reagent identity, purity, compatibility, pH, osmolality, sterility, or suitability for a physiological experiment.

A target concentration above the stock concentration would require a concentration step, not a dilution, so the calculated stock volume would exceed the intended final volume. Choose a stronger stock or consult the method rather than interpreting that result as an ordinary dilution. A zero stock concentration also cannot supply solute; the calculator’s formula is undefined in that case.

Related Dilution Calculations

For a series of dilutions, each step uses the concentration entering that step as its stock concentration. The total dilution factor is the product of the individual factors. For example, two successive tenfold dilutions produce an overall 100-fold dilution, assuming each transfer and final volume is accurate. Do not use the original stock concentration for every step unless the method actually makes each dilution directly from that original stock.

When several solutes are present, calculate each one separately only if each stock and final concentration are known and the method permits that approach. Adding multiple stock solutions can affect total volume and other solution properties, so the final mixture still needs to meet the protocol’s requirements. Dilution arithmetic alone does not establish that a solution has the intended pH, ionic strength, or physiological effect.

Frequently Asked Questions

What formula does a physiology dilution calculator use?
The standard relationship is C₁V₁ = C₂V₂. Rearranging it gives the stock volume V₁ = C₂V₂/C₁.

Does the final volume include the stock solution?
Yes. Final volume is the total volume of the prepared solution, including stock and diluent. It is not the volume of diluent alone.

Can I dilute a solution to a higher concentration?
No. Dilution reduces concentration. If the requested target exceeds the stock concentration, use a more concentrated starting solution or a method designed to concentrate the solution.

Can I use different units for stock and target concentration?
Convert them to the same units first. For example, convert mol/L to mmol/L by multiplying by 1,000, then enter both concentrations in mmol/L.

Is the calculated diluent volume always exact?
It is the arithmetic difference between final and stock volumes. Follow the protocol’s final-volume instructions, because solution volumes may not be perfectly additive and the method may require making the mixture up to a defined final volume.

Related

Formula used
in cs | Stock concentration | mmol/L | 100 | 0
in cf | Target concentration | mmol/L | 10 | 0
in vf | Final solution volume | mL | 100 | 0
out vs | Stock solution required | mL | cf * vf / cs | 2
out vd | Diluent required | mL | vf - vs | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →