molecalculator

Moles & Molar Mass

Ka from pKa: Formula and Calculator

Calculator No. 01-3768 · Updated · Formula and assumptions shown below

Ka 1.738 × 10−5
log10(Ka)
-4.76
= 0 − pKa
pKa
4.76
Set in the form below
You enter
pKa
You get
Ka, log10(Ka)
Rounding
6 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Calculate the acid dissociation constant, Ka, from pKa with Ka = 10−pKa. Enter a pKa value to get Ka as a dimensionless equilibrium constant; the calculator also gives log10(Ka) as a check.

Formula

The conversion is Ka = 10−pKa. In logarithmic form, pKa = −log10(Ka), so taking the base-10 antilogarithm of the negative pKa reverses the logarithm.

  • pKa is the negative base-10 logarithm of Ka; it is dimensionless.
  • Ka is the acid dissociation equilibrium constant, conventionally treated as dimensionless when expressed using activities relative to standard states. In introductory calculations, concentrations are often used as approximations.

The calculator writes the exponent as 0 − pKa, which is the same as −pKa. The second output, log10(Ka), should equal −pKa, providing a simple consistency check. Ka is displayed to six decimal places when that is useful; very small or large values may be displayed in scientific notation.

Worked Example

For the default pKa of 4.76:

  1. Negate the pKa: −pKa = 0 − 4.76 = −4.76.
  2. Raise 10 to that power: Ka = 10−4.76 = 0.000017378008.
  3. Check the logarithmic output: log10(Ka) = −4.76, which is shown to two decimal places.

Thus, for this example, Ka = 1.737801 × 10−5 (approximately). The exact value is determined by the input pKa; rounding the displayed result does not change the underlying conversion.

Assumptions

  • The pKa value is supplied for the relevant acid, solvent, temperature, and other stated conditions; no value is universal for every environment.
  • The calculation treats the reported pKa as a numerical value and uses the base-10 definition.
  • Ka is understood using the convention used by the source of the pKa. In rigorous thermodynamics, equilibrium constants are defined from activities; concentration-based values may be conditional or approximate.

What pKa and Ka Mean

For a weak acid HA in water, the dissociation equilibrium is commonly written:

HA ⇌ H+ + A−

Its concentration-based equilibrium expression is often introduced as:

Ka = [H+][A−] / [HA]

Square brackets denote equilibrium concentrations. In a thermodynamic treatment, activities replace concentrations so the equilibrium constant is dimensionless. The simplified concentration expression is useful in many general chemistry problems, especially for dilute solutions, but it should not be mistaken for a universal constant independent of conditions.

pKa is a logarithmic way to report the same acid-strength information. Because of the minus sign, a lower pKa corresponds to a larger Ka and, generally, a stronger acid under the conditions represented by the data. A higher pKa corresponds to a smaller Ka and less dissociation at equilibrium. The logarithmic scale makes values spanning many powers of ten easier to compare.

How to Use the Result

Enter the pKa from a reliable reference or from the problem statement, keeping its conditions in mind. The calculator converts that number directly; it does not determine pKa from a chemical identity, measure an acid, or account for a change in temperature or solvent.

  • For pKa = 2, Ka = 10−2 = 0.01.
  • For pKa = 7, Ka = 10−7 = 0.0000001.
  • For pKa = −1, Ka = 10, which is greater than 1.

These examples show why a negative pKa is valid: it simply gives a Ka greater than one under the stated convention. Do not assume every acid must have a positive pKa or every Ka must be below one. Whether an equilibrium constant is above or below one reflects the relative favorability of the products and reactants in the chosen standard-state convention.

When using Ka in a later equilibrium calculation, keep the conventions consistent. A Ka reported for a particular solvent or temperature may not be appropriate for a different medium or condition. Likewise, a table may report a thermodynamic value while a classroom exercise uses concentrations as an approximation.

Common Mistakes and Limits

  • Dropping the negative sign: The correct equation is 10−pKa, not 10pKa. For a positive pKa, omitting the minus sign produces a vastly different answer.
  • Using the wrong logarithm: pKa is defined with base 10. Do not use e−pKa or a natural logarithm for this conversion.
  • Confusing pKa with pH: pKa characterizes an equilibrium under stated conditions; pH describes hydrogen-ion activity in a particular solution. They are related in buffer calculations but are not interchangeable.
  • Over-rounding: A small pKa change can produce a noticeable multiplicative change in Ka. Retain suitable significant figures during intermediate work, then round the final result to match the precision of the source value.
  • Ignoring conditions: Solvent, temperature, ionic strength, and the chosen equilibrium convention can affect reported values. The conversion changes no chemistry; it only changes the numerical format.

For context, the Henderson–Hasselbalch relationship for a weak-acid/conjugate-base buffer is often written pH = pKa + log10([A−]/[HA]). It shows how pKa helps describe buffer behavior, but it is a separate relationship and does not replace Ka = 10−pKa. The buffer equation also relies on suitable assumptions and concentration approximations; pH meter readings are the real check, because temperature and ionic strength shift pH.

Frequently Asked Questions

What is the equation for Ka from pKa?
Use Ka = 10−pKa. Take 10 to the power of the negative pKa value.

How do I calculate pKa from Ka?
Use pKa = −log10(Ka). For example, if Ka = 10−5, then pKa = 5.

Does a lower pKa mean a stronger acid?
Generally, yes: a lower pKa means a larger Ka and greater dissociation tendency under the conditions represented by the values. Comparisons are meaningful only when the conditions and conventions are compatible.

Can Ka be greater than 1?
Yes. A negative pKa produces Ka greater than 1. The conversion does not impose a rule that Ka must be below one.

Does pKa have units?
No. It is a logarithm of an equilibrium constant and is dimensionless. Thermodynamic equilibrium constants are dimensionless when defined using activities and standard states.

Does this conversion depend on temperature?
The arithmetic does not, but the pKa value can depend on temperature and other conditions. Use a pKa appropriate to the system you are analyzing.

For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.

Related

Formula used
in pka | pKa | - | 4.76 | -
out ka | Ka | - | 10 ^ (0 - pka) | 6
out logka | log10(Ka) | - | 0 - pka | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →