“Gas cylinder size K” usually means the North American K-size industrial gas cylinder, a large high-pressure cylinder with a water capacity of about 49 litres (1,730 US fluid ounces). This page calculates approximate K-cylinder gas capacity from its water volume and pressure, then gives the equivalent volume at a stated reference pressure and temperature.
Formula
The calculator estimates the equivalent volume of gas using the ideal-gas relationship, with cylinder water capacity as the cylinder’s internal volume:
Vref = Vcyl × Pcyl × Tref / (Tcyl × Pref)
- Vref is the estimated gas volume at the reference conditions, in litres.
- Vcyl is cylinder water capacity, in litres. Water capacity is the internal volume, not the amount of gas available at atmospheric pressure.
- Pcyl is cylinder pressure in bar absolute.
- Tcyl is the gas temperature in kelvins, calculated as °C + 273.15.
- Pref is reference pressure in bar absolute. The default, 1.01325 bar, is one standard atmosphere.
- Tref is reference temperature in kelvins, calculated as °C + 273.15.
Pressure must be absolute: add atmospheric pressure to a gauge-pressure reading. The calculator uses the ideal-gas approximation and does not account for gas-specific compressibility at high pressure.
Worked Example
Using the default values—49 L water capacity, 200 bar absolute cylinder pressure, cylinder and reference temperatures of 20 °C, and reference pressure of 1.01325 bar:
Tcyl = 20 + 273.15 = 293.15 K
Tref = 20 + 273.15 = 293.15 K
Vref = 49 L × 200 bar × 293.15 K / (293.15 K × 1.01325 bar)
Vref = 9,671.847 L ≈ 9,672 L
The matching water-capacity output is 49.000 L. The large gas-volume figure is an idealized equivalent at the stated reference conditions, not the cylinder’s physical size. Real usable delivery can be lower because the cylinder cannot generally be emptied to zero pressure, and real gases deviate from ideal behavior.
Assumptions
- Gas behaves ideally; deviations may matter for compressed gas, depending on gas identity, pressure and temperature.
- Pressure inputs are absolute, not gauge pressure.
- The cylinder’s labeled water capacity is used as its internal volume.
- The estimate treats the gas temperature as uniform and uses the chosen reference conditions.
- The result is an approximate volume conversion, not a fill, handling or operating instruction.
What K Size Means
K is a cylinder-size designation used in some North American industrial-gas contexts; it is not a universal international standard. A nominal K cylinder is commonly listed with a water capacity near 49 L (about 1.73 cubic feet). Supplier specifications and cylinder markings are the authority for an individual cylinder, since dimensions, tare mass, service pressure and valve arrangement can vary.
The word “size” can refer to several different measurements: internal water capacity, overall height and diameter, filled or empty weight, pressure rating, or the quantity of gas contained. These are not interchangeable. A cylinder can have roughly the same external size as another while having a different service pressure or gas content. Confirm the cylinder’s stamped or labeled data rather than identifying it from appearance alone.
How the Estimate Works
At a fixed temperature, an ideal gas’s volume is proportional to its absolute pressure. A 49 L cylinder at 200 bar therefore contains an amount of gas that would occupy approximately 9,672 L at one atmosphere and the same temperature. If the temperature changes, the estimate adjusts in proportion to absolute temperature; if the reference pressure changes, the equivalent volume changes inversely.
Gauge pressure is measured above the surrounding atmosphere. For example, a gauge reading of 200 bar is approximately 201.013 bar absolute at standard atmospheric pressure. Using 200 as an absolute pressure when it is actually a gauge reading slightly underestimates the calculated amount. The difference grows in importance at lower cylinder pressures.
High-pressure gases are not perfectly ideal. The amount of error depends on the particular gas and conditions, so an exact inventory or engineering calculation may require a compressibility factor or manufacturer gas-content table. The calculator is useful for an approximate conversion, not for verifying a rated fill or designing equipment.
Choosing and Comparing a Cylinder
When comparing a K cylinder with another size, check the same basis for both: water capacity, service pressure, gas type and stated reference conditions. The name alone does not reliably establish how much usable gas is inside. A “cylinder volume” in a listing may mean the vessel’s water capacity, while a separate gas-volume figure may be reported at specified reference conditions.
- Read the cylinder label and markings for gas identity, service pressure and inspection information.
- Check water capacity or a gas-content figure, and note the temperature and pressure basis used.
- Consider the complete cylinder’s handling weight, not just its empty vessel weight.
- Verify valve compatibility and the intended regulator and equipment with a qualified gas supplier or responsible facility.
- For transport, storage and use, follow applicable local rules and the gas supplier’s instructions.
Dimensions and mass are not calculated here because they depend on the cylinder’s design and construction. The K designation is not a substitute for checking those values on the specific cylinder.
Safety and Common Misunderstandings
A gas cylinder is a pressure vessel. Secure it against falling, protect its valve, use it only with compatible equipment, and keep it away from heat and other hazards identified for the particular gas. Gas-specific hazards differ: some gases displace oxygen, some support combustion, and some are toxic or corrosive. Consult the safety data sheet (SDS) and applicable rules. Do not use a cylinder with damaged markings, a damaged valve or uncertain contents; arrange assessment by an authorized supplier or qualified professional.
Do not confuse the estimated free-gas volume with the amount that can safely or practically be drawn off. Residual pressure, regulator limits, temperature changes, flow rate and the gas’s behavior affect usable supply. Never infer a safe fill pressure from a size designation or this calculation.
Frequently Asked Questions
How many litres is a K-size gas cylinder?
A nominal K cylinder is commonly described as having about 49 L of water capacity. That is the cylinder’s internal volume, not its atmospheric-pressure gas capacity.
How much gas does a 49 L cylinder hold at 200 bar?
For the calculator’s defaults, the ideal-gas estimate is about 9,672 L at 1.01325 bar absolute and 20 °C. Actual gas quantity and usable delivery depend on gas identity, pressure basis, residual pressure and non-ideal behavior.
Is K cylinder size the same everywhere?
No. Cylinder letters and nominal sizes are not universal across countries and industries. Check the markings and the supplier’s specification for the particular cylinder.
Does 49 L mean the cylinder contains only 49 litres of gas?
No. It is the water capacity—the internal vessel volume. Gas compressed into the vessel expands to a much larger equivalent volume when brought to a lower reference pressure.
Is 200 bar gauge the same as 200 bar absolute?
No. Gauge pressure excludes atmospheric pressure; absolute pressure includes it. At standard atmospheric pressure, 200 bar gauge is approximately 201.013 bar absolute.
Related
Formula used
in v | Water capacity | L | 49 | 0.001 in p | Cylinder pressure, absolute | bar | 200 | 0.001 in t | Gas temperature | °C | 20 | -273.15 in r | Reference pressure, absolute | bar | 1.01325 | 0.001 in tr | Reference temperature | °C | 20 | -273.15 out g | Approximate gas volume at reference conditions | L | v * p * (tr + 273.15) / ((t + 273.15) * r) | 0 out w | Water capacity | L | v | 1
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Cubic Meters per Hour to Liters per Second0.2778 L/s