The gas volume–pressure formula for a fixed amount of gas at constant temperature is Boyle’s law: P₁V₁ = P₂V₂. This calculator uses an initial pressure and volume plus a final volume to calculate the final pressure, with both pressures expressed in kPa and volumes in L.
Formula
Boyle’s law states that, at constant temperature and for a fixed amount of gas, pressure multiplied by volume remains constant:
P₁V₁ = P₂V₂
Rearrange to calculate the final pressure:
P₂ = P₁ × V₁ ÷ V₂
- P₁ is the initial absolute pressure, in kilopascals (kPa).
- V₁ is the initial gas volume, in liters (L).
- P₂ is the final absolute pressure, in kPa.
- V₂ is the final gas volume, in L.
Use the same pressure unit on both sides and the same volume unit on both sides. The calculator reports P₂ in kPa. Pressure must be absolute pressure, measured relative to a perfect vacuum, rather than gauge pressure measured relative to the surrounding atmosphere.
Worked Example
Using the calculator’s default values, compress a fixed quantity of gas from 1 L at 101.325 kPa to 2 L. The calculation is:
P₂ = P₁ × V₁ ÷ V₂
P₂ = 101.325 kPa × 1 L ÷ 2 L
P₂ = 50.6625 kPa ≈ 50.663 kPa
The volume has doubled, so Boyle’s law predicts that the absolute pressure has halved. The result is rounded to three decimal places, as in the calculator output.
Assumptions
- The amount of gas remains fixed: none enters, escapes, reacts, or condenses.
- The gas temperature is constant during the change.
- The gas behaves ideally enough for Boyle’s law to be a suitable approximation.
- Pressures are absolute, not gauge pressures.
How the Pressure–Volume Relationship Works
For a fixed amount of gas at constant temperature, molecules move randomly and collide with the container walls. Reducing the space available does not remove molecules; instead, they reach the walls more often per unit area and time, increasing pressure. Increasing the volume has the opposite effect.
This inverse relationship can also be written as P ∝ 1/V, or PV = constant. If the volume is multiplied by a factor, the absolute pressure is divided by that same factor. For example, halving a gas’s volume doubles its pressure, provided the assumptions of Boyle’s law hold.
Boyle’s law is one part of the ideal gas law, PV = nRT. In that equation, n is the amount of gas in moles, R is the gas constant, and T is absolute temperature in kelvins. When n and T stay unchanged, nRT is constant, leaving PV constant. The broader equation is useful when the amount or temperature changes too.
Using the Calculator and Reading the Result
Enter the initial absolute pressure, initial volume, and final volume. The output is the pressure the gas would have after reaching the stated final volume under Boyle’s law conditions. A smaller final volume gives a higher answer; a larger final volume gives a lower one.
For example, if the gas starts at 200 kPa and 3 L and ends at 1.5 L, the final pressure is 200 × 3 ÷ 1.5 = 400 kPa. The volume is halved, and the predicted absolute pressure doubles.
The calculator requires positive values for pressure and volume. A zero volume would make the division undefined, and negative pressure or volume is not meaningful for this calculation. Round the displayed result only as much as the precision of the measurements warrants; extra decimal places do not make imprecise measurements more accurate.
Units, Gauge Pressure, and Common Errors
Unit consistency is essential. Liters can be used with milliliters if both volumes use the same unit, because the units cancel in the ratio V₁/V₂. If one volume is in liters and the other in milliliters, convert one before calculating: 1 L = 1000 mL. Likewise, convert pressures to a common unit before using the formula.
A frequent mistake is substituting gauge pressure for absolute pressure. Boyle’s law uses pressure relative to a vacuum. For a gauge reading, first add local atmospheric pressure to obtain absolute pressure; near standard atmospheric conditions, that is approximately 101.325 kPa, though actual atmospheric pressure varies with weather and altitude. Perform the Boyle’s law calculation using absolute pressures, then convert back to gauge pressure if that is the quantity you need to report.
Another common error is assuming that pressure changes only because volume changes. If the gas warms or cools, pressure may change even at the same volume. Likewise, a leak, a change in the amount of gas, or substantial non-ideal behavior can invalidate a simple Boyle’s law prediction.
Limits and When to Use a Broader Gas Law
Boyle’s law is most useful for estimating how pressure and volume relate when temperature and gas quantity stay constant. Real gases depart from ideal behavior, especially at high pressures or near condensation, because molecules occupy space and interact with one another. Under such conditions, a real-gas model may be needed rather than the simple inverse relationship.
If temperature also changes, use the combined gas law for a fixed amount of gas: P₁V₁/T₁ = P₂V₂/T₂, with temperature in kelvins. If the amount of gas changes as well, the ideal gas law, PV = nRT, can account for pressure, volume, temperature, and moles together. Do not compare Celsius temperatures in these gas-law ratios: convert using T(K) = T(°C) + 273.15.
These equations describe relationships; they do not establish that a real container, process, or setup can safely withstand a calculated pressure. For any bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.
Frequently Asked Questions
What is the formula for gas pressure and volume?
For a fixed amount of gas at constant temperature, Boyle’s law is P₁V₁ = P₂V₂. To find final pressure, use P₂ = P₁V₁/V₂.
Does pressure increase when gas volume decreases?
Yes, if the amount of gas and temperature stay constant. Pressure is inversely proportional to volume: halving the volume doubles the absolute pressure in the Boyle’s law model.
Can I use Celsius in Boyle’s law?
Boyle’s law does not require a temperature value when temperature is constant. If temperature changes and you use a broader gas law, use kelvins, not Celsius.
Should I use gauge or absolute pressure?
Use absolute pressure in gas-law equations. Add atmospheric pressure to a gauge-pressure reading before calculating; convert the result back to gauge pressure only afterward if needed.
What if the gas temperature changes?
Boyle’s law alone no longer describes the full change. For a fixed amount of gas, use the combined gas law and enter temperatures in kelvins.
Related
Formula used
in p1 | Initial pressure | kPa | 101.325 | 0 in v1 | Initial volume | L | 1 | 0 in v2 | Final volume | L | 2 | 0 out p2 | Final pressure | kPa | p1 * v1 / v2 | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Cubic Meters per Hour to Liters per Second0.2778 L/s