molecalculator

Moles & Molar Mass

Molarity Calculator: Find Solution Concentration

Calculator No. 01-5560 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator finds molarity, the amount of solute in moles per liter of finished solution. Enter the solute mass, its molar mass, and the final solution volume to get molarity and the equivalent concentration in millimolar.

Formula

Molarity is the number of moles of solute divided by the final volume of the solution in liters:

c = n / V = (m / M) / (v / 1000)

  • c is molarity, in mol/L.
  • n is the amount of solute, in moles.
  • m is the solute mass, in grams.
  • M is the solute molar mass, in g/mol.
  • V is final solution volume, in liters.
  • v is the same final volume entered in milliliters; dividing by 1000 converts mL to L.

The calculator combines the two steps: calculate moles as mass divided by molar mass, then divide by liters of solution. Millimolar concentration uses 1 mol/L = 1000 mM, so its value is c × 1000.

Worked Example

Using the calculator defaults—2.922 g of solute, a molar mass of 58.44 g/mol, and 250 mL final volume:

  1. Find the amount of solute: n = 2.922 g / 58.44 g/mol = 0.050000 mol.
  2. Convert the solution volume: V = 250 mL / 1000 = 0.250 L.
  3. Divide amount by final volume: c = 0.050000 mol / 0.250 L = 0.2000 mol/L.
  4. Convert to millimolar: 0.2000 mol/L × 1000 = 200.00 mM, displayed as 200 mM.

Assumptions

  • The entered mass is the mass of the solute, and the entered molar mass matches that substance and chemical form.
  • The volume is the final volume of the whole solution, not the amount of solvent used.
  • The calculation assumes the solute is represented by its formula-unit or molecular molar mass; it does not adjust for dissociation, reaction, purity, or volume changes.

When to Use Molarity

Molarity is useful when comparing solution strengths or calculating how much substance is present in a measured volume. For example, a 0.2000 mol/L solution contains 0.2000 moles of solute in each liter of solution. In 100 mL, it contains 0.02000 mol, because amount equals molarity multiplied by volume in liters.

It is commonly used in reaction stoichiometry, titration calculations, and general solution chemistry. It is especially convenient when the calculation uses solution volumes measured in liters or milliliters. For very dilute solutions, millimolar or micromolar units can make the number easier to read, but the underlying concentration is unchanged.

Choosing the Molar Mass

Molar mass depends on the chemical formula and, for some materials, the form specified on the label. Use a reliable formula or reference value for the exact substance. For a compound, add the atomic masses for every atom in its formula, accounting for subscripts. For instance, sodium chloride, NaCl, has a molar mass of about 58.44 g/mol using standard atomic weights of 22.990 for sodium and 35.45 for chlorine.

Check whether the material is an anhydrous compound, a hydrate, or a salt with a different counterion. These forms have different molar masses. If the substance is a mixture or its purity is below 100%, this calculator does not correct for that: the mass entered is treated as pure solute. Any purity correction requires reliable purity information and a separate calculation.

Common Errors and Limits

  • Using solvent volume: If a method calls for a final volume of 250 mL, the solution must have a total volume of 250 mL. Adding solute to 250 mL of solvent may produce a different final volume.
  • Mixing units: Enter mass in grams, molar mass in grams per mole, and volume in milliliters. The calculator converts milliliters to liters; entering a value in liters as though it were milliliters makes the answer 1000 times too large.
  • Rounding too early: Keep suitable precision in the molar mass and intermediate values, then round the reported concentration to match the precision of the measurements.
  • Assuming molarity never changes: Molarity is based on volume, and liquid volume can vary with temperature. For work requiring high accuracy, use conditions and methods appropriate to the measurement.

This is a mass-and-volume calculation, not a measurement of chemical activity or reaction yield. It also does not determine pH, account for incomplete dissolution, or establish whether a solution is suitable for a particular experiment. Where bench work is implied, follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

How do I calculate molarity from grams?
Divide the mass in grams by the molar mass in g/mol to get moles. Divide that amount by the final solution volume in liters.

Why do I use final solution volume instead of solvent volume?
Molarity is defined per volume of the complete solution. Dissolved solute can change the total volume, so solvent volume alone is not the correct denominator.

What is the difference between molarity and millimolarity?
They express the same type of concentration at different scales. One molar (1 mol/L) equals 1000 millimolar (1000 mM).

Can I calculate molarity if I only know the mass and volume?
You also need the solute’s molar mass to convert its mass into moles. If you know the chemical identity and formula, you can obtain its molar mass from its atomic composition.

Does molarity change with temperature?
It can, because solution volume may expand or contract as temperature changes. The amount of solute remains the same, but molarity is defined using volume, which can be temperature-dependent.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →