molecalculator

Moles & Molar Mass

Gas Volume Triangle: Boyle’s, Charles’s and Combined Laws

Calculator No. 01-5648 · Updated · Formula and assumptions shown below

Final gas volume 1.0000 L
Initial pressure
101.325 kPa
Set in the form below
Initial volume
1 L
Set in the form below
Initial temperature
25 °C
Set in the form below
Final pressure
101.325 kPa
Set in the form below
You enter
Initial pressure (kPa), Initial volume (L), Initial temperature (°C), Final pressure (kPa), Final temperature (°C)
You get
Final gas volume (L)
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A gas volume triangle is a memory aid for rearranging a gas-law equation to find an unknown volume, pressure, or temperature; it is not a single scientific law. This calculator uses the combined gas law to find a gas’s final volume from its initial pressure, volume, and temperature and its final pressure and temperature.

Formula

The calculator uses the combined gas law, which relates the pressure, volume, and absolute temperature of a fixed amount of gas when the gas behaves approximately ideally:

P₁V₁/T₁ = P₂V₂/T₂, rearranged as V₂ = V₁ × (P₁/P₂) × (T₂/T₁).

  • P₁, P₂ are initial and final absolute pressures in kilopascals (kPa).
  • V₁, V₂ are initial and final volumes in liters (L).
  • T₁, T₂ are absolute temperatures in kelvins (K).
  • For temperatures entered in degrees Celsius, convert using T in K = temperature in °C + 273.15.

Use absolute pressure, not gauge pressure. If a pressure is reported relative to the surrounding atmosphere, convert it before using the equation: absolute pressure is gauge pressure plus the local atmospheric pressure. Pressure units can be any consistent unit in the ratio, but this calculator accepts kPa for both pressure entries. The ratio cancels the unit.

Worked Example

Using the calculator’s default values: P₁ = 101.325 kPa, V₁ = 1 L, initial temperature = 25 °C, P₂ = 101.325 kPa, and final temperature = 25 °C.

  1. Convert both temperatures to kelvins: T₁ = 25 + 273.15 = 298.15 K; T₂ = 25 + 273.15 = 298.15 K.
  2. Substitute into the rearranged equation: V₂ = 1 × (101.325/101.325) × (298.15/298.15) L.
  3. Evaluate the ratios: V₂ = 1 × 1 × 1 L = 1.0000 L.

The gas volume remains unchanged because pressure and absolute temperature are the same at the start and end.

What a Gas Volume Triangle Means

A triangle is a classroom mnemonic, not a separate formula. In a simple relationship such as Boyle’s law, placing P and V above a line with a constant below can remind students that pressure multiplied by volume is constant for a fixed amount of gas at constant temperature. Covering a symbol may suggest an algebraic rearrangement, but the diagram does not define the conditions or units. Always write the underlying equation and check that its assumptions fit the problem.

Different gas-law triangles may represent different relationships. Boyle’s law links pressure and volume at constant temperature; Charles’s law links volume and absolute temperature at constant pressure; and the combined gas law accounts for changes in pressure and temperature for a fixed quantity of gas. The calculator above uses the combined gas law. It does not calculate a new amount of gas or account for chemical reactions.

How Volume Changes With Pressure and Temperature

The formula makes two useful trends visible. If temperature stays constant, increasing absolute pressure decreases volume in inverse proportion. For example, doubling the pressure while holding everything else fixed halves the predicted volume. If pressure stays constant, increasing the kelvin temperature increases volume in direct proportion. Celsius values cannot be used directly in that ratio: 20 °C is not twice as hot as 10 °C in the thermodynamic sense.

When both conditions change, multiply the two ratios. Suppose a gas starts at 1.00 L, 100 kPa, and 20 °C, then ends at 200 kPa and 20 °C. The pressure ratio is 100/200 = 0.5 and the temperature ratio is 293.15/293.15 = 1, so its predicted final volume is 0.50 L. This example assumes the amount of gas is unchanged and ideal-gas behavior is adequate.

When the Combined Gas Law Applies

The relation follows from the ideal gas law, PV = nRT, by comparing two states where the amount of gas n is constant. It is most useful for estimating how a sealed, fixed amount of gas changes volume as pressure or temperature changes. It is not a complete model for every gas or every situation.

  • Use absolute pressure. A gauge reading of zero means pressure is approximately atmospheric, not zero absolute pressure.
  • Use kelvins in temperature ratios. Convert °C by adding 273.15.
  • Keep the gas amount fixed. Leaks, venting, gas generation, or gas consumption invalidate the simple comparison.
  • Use the same pressure unit for P₁ and P₂. The calculator uses kPa.

For many gases at ordinary temperatures and pressures, the ideal-gas approximation is practical. At high pressure or near condensation, intermolecular forces and the finite size of molecules matter more, so real-gas models or measured data may be needed. If the gas is in a flexible container, its pressure may also be affected by the container and its surroundings rather than being an independently fixed input.

Common Mistakes and Limits

A frequent error is entering gauge pressure as if it were absolute. Another is inserting Celsius directly into T₂/T₁; this can produce a plausible-looking but incorrect result. For example, a temperature of 20 °C must be entered as 293.15 K in the equation, not 20. If the pressure units differ, convert one value so both match before taking their ratio.

Volume units carry through from V₁: because the calculator takes V₁ in liters, it returns V₂ in liters. Convert other volume units before entering them. The displayed result is rounded to four decimal places, so retain more digits during intermediate work when precision matters. The number of displayed digits does not imply that the measurements themselves are accurate to that precision.

This calculation does not determine pressure from a closed container’s material limits, predict a phase change, or include gas dissolved in a liquid. It also assumes the initial and final states describe the same gas sample. Where these assumptions fail, use an equation of state suited to the material and conditions or consult an appropriate measured reference.

Frequently Asked Questions

What is a gas volume triangle?
A gas volume triangle is a study aid for rearranging a gas-law equation. It is not a universal formula; identify which law the triangle represents and apply that law’s conditions.

How do I find gas volume from pressure and temperature?
For a fixed amount of gas, use V₂ = V₁(P₁/P₂)(T₂/T₁), with absolute pressures and temperatures in kelvins. The calculator applies this combined gas law.

Do I use Celsius or Kelvin in a gas law?
Use kelvins in gas-law ratios. Convert Celsius to kelvins by adding 273.15. Celsius readings may be entered in this calculator because it performs that conversion.

Can I use gauge pressure?
Not directly. Convert gauge pressure to absolute pressure by adding local atmospheric pressure, then use absolute values for both states.

Is the triangle itself a gas law?
No. It is a mnemonic for remembering or rearranging a relationship. The actual law, its variables, units, and assumptions determine whether a calculation is valid.

Related

Formula used
in p1 | Initial pressure | kPa | 101.325 | 0.000001
in v1 | Initial volume | L | 1 | 0.000001
in t1 | Initial temperature | °C | 25 | -273.15
in p2 | Final pressure | kPa | 101.325 | 0.000001
in t2 | Final temperature | °C | 25 | -273.15
out v2 | Final gas volume | L | v1 * (p1 / p2) * ((t2 + 273.15) / (t1 + 273.15)) | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →