Absorbance (A) is calculated from the amount of light a sample transmits using the formula A = log10(I0 / I) = -log10(T), where I0 is the incident light intensity, I is the transmitted light intensity, and T is the transmittance expressed as a decimal fraction. In practice, you enter the percent transmittance (%T) from a spectrophotometer into the calculator below, and it returns the absorbance value. The calculator also converts absorbance back to percent transmittance, which is useful when you need to check a reading or plan dilutions.
Formula
The fundamental relationship is the Beer–Lambert law, which links absorbance to the concentration of the absorbing species and the path length of the light through the sample:
A = ε · c · l
- A – absorbance (unitless, often reported in “absorbance units” or AU)
- ε – molar absorptivity (also called molar extinction coefficient), in L·mol−1·cm−1
- c – concentration of the absorbing species, in mol/L
- l – path length of the cuvette, in cm (typically 1.00 cm)
Because absorbance is defined as A = log10(I0/I), and transmittance T = I/I0, the two are related by A = −log10(T). When the spectrophotometer displays %T, you divide by 100 to get T, then take the negative base‑10 logarithm. The calculator above does exactly that conversion.
Worked Example
Suppose a sample shows 50.0% transmittance on the instrument. Using the calculator defaults:
- Convert percent transmittance to a fraction: T = 50.0 / 100 = 0.500
- Take the negative base‑10 logarithm: A = −log10(0.500)
- log10(0.500) = −0.3010, so A = −(−0.3010) = 0.3010
The calculator returns A = 0.3010 AU and T = 0.5000. This matches the well‑known fact that 50% transmittance corresponds to an absorbance of about 0.301.
Assumptions
- The sample is in a cuvette with a fixed, known path length (usually 1 cm).
- The solution is dilute enough that the Beer–Lambert law holds linearly.
- The incident light is monochromatic (a single wavelength) and the sample is homogeneous.
- No scattering or fluorescence contributes to the measured light loss.
Why Absorbance Is Logarithmic
Absorbance is not a direct measure of how much light is blocked; it is a logarithmic measure of the ratio of incident to transmitted light. This is because each infinitesimal layer of the solution absorbs the same fraction of the light passing through it, not the same absolute amount. If a 1 cm path absorbs 50% of the light, a second 1 cm path absorbs 50% of the remaining 50%, leaving 25% transmitted. The absorbance adds linearly: 0.301 + 0.301 = 0.602, while the transmittance multiplies (0.5 × 0.5 = 0.25). This additive property is why absorbance is used for quantitative analysis – it is directly proportional to concentration, whereas transmittance is not.
How to Read Absorbance Values
Most spectrophotometers are calibrated to read 0 absorbance (100% transmittance) with a blank solution. A reading of 0 means all light passes through; a reading of 1 means 10% transmittance (90% absorbed); a reading of 2 means 1% transmittance (99% absorbed). In practice, reliable measurements fall between A = 0.1 and A = 2.0. Below 0.1, the signal is too close to the blank and noise dominates. Above 2.0, so little light reaches the detector that the reading becomes unreliable and nonlinear. If your sample gives an absorbance above 2, dilute it and multiply the result by the dilution factor.
Common Mistakes and Unit Mix-Ups
- Forgetting to divide %T by 100: Using 50 directly in the logarithm gives log(50) ≈ 1.70 instead of 0.301. Always convert to a fraction first.
- Using natural log instead of base‑10: Absorbance is defined with base‑10 log. If you use ln, you get a value 2.303 times larger. Some instruments report “absorbance” using natural log for certain kinetic measurements, but the standard definition is base‑10.
- Ignoring the blank: The blank (solvent and all reagents except the analyte) must be measured and subtracted, or set to zero on the instrument, to correct for cuvette and solvent absorption.
- Path length errors: If the cuvette is not 1.00 cm, the absorbance changes linearly with path length. A 1 cm cuvette is standard; using a 0.5 cm cuvette halves the absorbance.
- Round-off errors: Report absorbance to three decimal places (e.g., 0.301), which matches the precision of most instruments.
Using Absorbance to Find Concentration
Once you have the absorbance, you can find concentration if you know the molar absorptivity (ε) and path length (l): c = A / (ε·l). For example, if ε = 15000 L·mol−1·cm−1 (a typical value for a strongly absorbing dye) and l = 1.00 cm, then an absorbance of 0.301 corresponds to c = 0.301 / (15000 × 1.00) = 2.01 × 10−5 mol/L. In practice, you would construct a calibration curve with known concentrations, plot absorbance vs. concentration, and use the slope (which equals ε·l) to determine unknown concentrations. The linear range of the calibration curve is where the Beer–Lambert law holds.
Limits of the Beer–Lambert Law
The linear relationship between absorbance and concentration fails under several conditions:
- High concentration: At concentrations above about 0.01 mol/L, intermolecular interactions and changes in refractive index cause deviations.
- Chemical equilibria: If the absorbing species dimerizes, dissociates, or reacts with the solvent, the effective concentration changes with total concentration.
- Polychromatic light: If the instrument does not isolate a narrow wavelength band, the absorbance is not exactly linear because ε varies with wavelength.
- Scattering: Turbid suspensions scatter light, which is counted as absorption, inflating the absorbance reading.
- Fluorescence: If the sample fluoresces, the emitted light reaches the detector and reduces the apparent absorbance.
For these reasons, always verify linearity with a calibration curve and stay within the concentration range where the law holds.
Frequently Asked Questions
How do I convert percent transmittance to absorbance?
Divide the percent transmittance by 100 to get the transmittance fraction, then take the negative base‑10 logarithm. For example, 25%T → T = 0.25 → A = −log10(0.25) = 0.602.
Why is absorbance unitless?
Absorbance is a ratio of two light intensities (I0/I), so the units cancel. It is often reported as “absorbance units” (AU) for clarity, but it has no physical dimension.
What is the difference between absorbance and transmittance?
Transmittance is the fraction of light that passes through the sample (I/I0), ranging from 0 to 1. Absorbance is the negative logarithm of transmittance, ranging from 0 (all light passes) to infinity (no light passes). Absorbance is linearly related to concentration; transmittance is not.
Can absorbance be greater than 1?
Yes. Absorbance of 1 corresponds to 10% transmittance, and absorbance of 2 corresponds to 1% transmittance. Values above 2 are possible but often unreliable due to detector limitations.
What is the blank used for?
The blank contains everything in the sample except the analyte (solvent, buffer, reagents). It corrects for absorption by the cuvette and the solvent. You zero the instrument with the blank so that the measured absorbance is due only to the analyte.
Does the path length always have to be 1 cm?
No, but it is the most common. The Beer–Lambert law includes path length explicitly, so if you use a 2 cm cuvette, the absorbance doubles for the same concentration. Always know your cuvette’s path length when calculating concentration.
Related
Formula used
in pct | Percent transmittance (%T) | % | 50 | 0 | 100 out A | Absorbance | AU | -log10(pct / 100) | 4 out T | Transmittance (fraction) | - | pct / 100 | 4
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Rate and Extent of Reaction: Key Facts0.050 mol/L
- How to Calculate Extent of Reaction0.800 mol
- Rate and Extent of Chemical Reactions0.1000 mol/(L·s)
- Chemical Reaction Formula: How to Write & Balance2.2722 mol
- Extent of Reaction Solver & How to Use It0.6000 mol
- Extent of Reaction Units: mol and Beyond