molecalculator

Moles & Molar Mass

How to Calculate Combustion Efficiency

Calculator No. 01-9976 · Updated · Formula and assumptions shown below

Combustion efficiency 96.7 %
Flue gas temperature
200 °C
Set in the form below
Ambient air temperature
25 °C
Set in the form below
Oxygen in flue gas
6 %
Set in the form below
You enter
Flue gas temperature (°C), Ambient air temperature (°C), Oxygen in flue gas (%)
You get
Combustion efficiency (%)
Rounding
1 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator determines combustion efficiency based on the flue gas temperature and the concentration of oxygen (O2) or carbon dioxide (CO2) in the exhaust. You enter the flue gas temperature, the ambient air temperature, and either the O2 or CO2 percentage, and you get the combustion efficiency as a percentage. The calculation uses the standard ASME PTC 4.1 indirect method, which estimates the sensible heat lost in the dry flue gas.

Formula

The combustion efficiency (η) is calculated using the Siegert formula, a simplified version of the indirect method:

η = 100 – ( ( A × O2 / (21 – O2) + B ) × (Tflue – Tair) / 100 )

Where:

  • η = combustion efficiency (%)
  • A = fuel-specific factor (for natural gas, A ≈ 3.5)
  • B = fuel-specific factor (for natural gas, B ≈ 0.5)
  • O2 = volume percentage of oxygen in the flue gas (dry basis)
  • Tflue = flue gas temperature (°C)
  • Tair = ambient air temperature (°C)

The factor (21 – O2) represents the excess air; the more excess air, the more heat is carried away. The constants A and B depend on the fuel type: for natural gas, A = 3.5 and B = 0.5; for fuel oil, A = 3.4 and B = 0.4; for coal, A = 3.3 and B = 0.4. This calculator uses natural gas values by default.

Worked Example

Using the default values: flue gas temperature = 200 °C, ambient air temperature = 25 °C, oxygen = 6%.

  1. Calculate the excess air term: O2 / (21 – O2) = 6 / (21 – 6) = 6 / 15 = 0.4
  2. Multiply by A: 3.5 × 0.4 = 1.4
  3. Add B: 1.4 + 0.5 = 1.9
  4. Calculate the temperature difference: Tflue – Tair = 200 – 25 = 175 °C
  5. Multiply: 1.9 × 175 = 332.5
  6. Divide by 100: 332.5 / 100 = 3.325
  7. Subtract from 100: 100 – 3.325 = 96.675%

The combustion efficiency is approximately 96.7%.

Assumptions

  • The fuel is natural gas (methane) with the given A and B factors.
  • The flue gas is measured on a dry basis (water vapor removed before analysis).
  • Complete combustion is assumed; the calculation only accounts for sensible heat loss in dry flue gas, not latent heat of water vapor or unburned fuel losses.
  • The ambient air temperature is the temperature of the combustion air entering the burner.
  • The specific heat of flue gas is approximated as constant over the temperature range.

When to Use This Calculator

Use this calculator to quickly assess the performance of a boiler, furnace, or other combustion equipment. It is most useful for routine tuning and monitoring, where you measure the flue gas temperature and oxygen content with a portable combustion analyzer. The result tells you how much of the fuel’s energy is being converted into useful heat versus being lost up the stack. Higher efficiency means lower fuel costs and reduced emissions.

How to Read the Result

The efficiency percentage represents the fraction of the fuel’s chemical energy that is transferred to the working fluid (water, air, etc.). For example, 96.7% efficiency means that 3.3% of the fuel’s energy is lost as sensible heat in the flue gas. In practice, real boilers often operate at 80-95% efficiency; values above 95% are possible with condensing boilers that recover latent heat, but this calculator does not account for that.

Common Mistakes

  • Using wet-basis O2 measurements: The formula assumes dry flue gas. If your analyzer reports O2 on a wet basis, you must correct for moisture or use a different method.
  • Ignoring the ambient temperature: Using the room temperature instead of the actual combustion air temperature can shift the result by a few percent.
  • Using the wrong fuel factors: A and B vary by fuel. Using natural gas factors for a coal boiler will give inaccurate results.
  • Measuring O2 in the wrong location: The probe must be placed where the flue gas is well mixed, typically after the last heat exchanger.
  • Rounding too early: Keep at least three significant figures in intermediate steps to avoid rounding errors in the final percentage.

Tips

  • Take multiple readings at different load conditions to get a representative average.
  • Ensure the combustion analyzer is calibrated according to the manufacturer’s instructions before each use.
  • For condensing boilers, use a dedicated calculation that includes latent heat recovery; this simple formula will underestimate efficiency.
  • If you have CO2 data instead of O2, you can convert using the relationship: O2 ≈ 21 – (CO2 × (21 / CO2,max)), where CO2,max is about 12% for natural gas.
  • Remember that this is a simplified method; for official performance tests, follow ASME PTC 4.1 or local standards.

Troubleshooting

Result is above 100%: This can happen if the flue gas temperature is lower than the ambient temperature (negative difference) or if the O2 reading is very low (near zero). Check your measurements; a negative temperature difference is physically impossible in a fired heater.

Result seems too low: High O2 (e.g., >15%) indicates excessive excess air, which dilutes the flue gas and increases heat loss. Check for air leaks in the furnace or adjust the burner air damper.

O2 reading is zero: This may indicate a faulty analyzer or that the probe is not in the flue gas stream. Verify the probe is inserted properly and the analyzer is calibrated.

You only have CO2 data: Use the conversion in the Tips section, or enter the O2 equivalent. For natural gas, if CO2 is 9%, then O2 ≈ 21 – (9 × (21/12)) = 21 – 15.75 = 5.25%.

Frequently Asked Questions

Q: What is the difference between combustion efficiency and boiler efficiency?
A: Combustion efficiency measures how completely the fuel’s chemical energy is released and transferred to the working fluid, ignoring other losses like radiation and convection from the boiler shell. Boiler efficiency includes all losses and is typically lower.

Q: Why is excess air important?
A: Excess air ensures complete combustion, but too much excess air carries away heat up the stack, reducing efficiency. The optimal level balances complete combustion with minimal heat loss.

Q: Can I use this for any fuel?
A: The calculator uses natural gas factors. For other fuels, you need to adjust A and B. For fuel oil, use A=3.4, B=0.4; for coal, use A=3.3, B=0.4. You can modify the formula accordingly.

Q: What is the typical efficiency of a natural gas boiler?
A: Non-condensing boilers typically operate at 80-85% efficiency, while condensing boilers can reach 95-98% (including latent heat recovery). This calculator gives the sensible heat efficiency, which for a condensing boiler might be around 90%.

Q: How often should I measure combustion efficiency?
A: For routine maintenance, measure monthly or quarterly. If you notice higher fuel bills or visible smoke, measure immediately.

Q: Does altitude affect the calculation?
A: The oxygen percentage is measured on a volume basis, which is independent of altitude. However, the actual mass flow of air changes with altitude, but that is not part of this simplified formula.

Related

Formula used
in t | Flue gas temperature | °C | 200 | 0 | 1000
in ta | Ambient air temperature | °C | 25 | -50 | 100
in o2 | Oxygen in flue gas | % | 6 | 0 | 21
out eff | Combustion efficiency | % | 100 - ( ( ( 3.5 * o2 ) / ( 21 - o2 ) + 0.5 ) * ( t - ta ) / 100 ) | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →