Calculate a solid model’s volume in Siemens NX by selecting the body and reading its mass properties, or use the calculator below for a quick geometry check. Enter the solid’s dimensions in consistent units to get its volume; the calculator assumes a complete rectangular solid, while NX can calculate more complex shapes directly from the model.
Formula
For a rectangular solid, volume equals length multiplied by width multiplied by height: V = l × w × h. Here, l is length in millimetres (mm), w is width in mm, and h is height in mm. The result V is in cubic millimetres (mm³). To convert cubic millimetres to cubic centimetres (cm³), divide by 1,000, because 1 cm³ = 1,000 mm³. The calculator’s first result is the volume in mm³; its second is the equivalent in cm³.
This simple formula is only for a rectangular solid. NX’s mass-properties calculation evaluates the actual selected solid body, including curves and complex features represented in its geometry. The result depends on the model’s units and on which bodies are included in the selection.
Worked Example
Using the calculator’s default values:
- Length = 100 mm, width = 50 mm, and height = 20 mm.
- Calculate cubic millimetres: V = 100 mm × 50 mm × 20 mm = 100,000 mm³, displayed as 100000.00 mm³.
- Convert to cubic centimetres: 100,000 mm³ ÷ 1,000 = 100.000 cm³.
The two results describe the same volume in different units. Your NX result will match this example only if the selected model is a rectangular solid with those dimensions and the same unit convention.
Assumptions
- The calculator treats the object as a rectangular solid, with all three dimensions greater than zero.
- Its inputs are millimetres; the displayed outputs are mm³ and cm³.
- The NX method uses the modeled solid’s geometry, not an estimate based only on its overall bounding dimensions.
- For a model with multiple bodies, the result depends on whether you select one body or all intended bodies.
What You’ll Need
- A part file containing a solid body in NX. Save or update the model so the displayed geometry reflects the features you intend to measure.
- Access to the mass-properties command. Command names and menu locations can differ between NX releases and workspaces.
- A clear decision about whether you need the volume of one body or the combined volume of several bodies.
Step-by-Step
- Open and check the part. Open the NX part and inspect the model. Confirm that the intended geometry is present and that there are no unfinished edits that should change the body. If your part contains several solids, identify which one or ones are relevant.
- Find the mass-properties tool. Search NX’s command finder for “Measure Bodies” or “Mass Properties,” or look for the mass-properties command in the analysis or measurement tools for your release. NX interfaces vary, so command search is often the most direct route. Choose the command that reports volume for solid bodies.
- Select the correct body or bodies. Select the solid body in the graphics window or the part navigator, following the command’s selection prompt. To measure a combined total, select all the bodies that should be included. Do not select a datum plane, face, sketch, sheet body, or unrelated component by mistake.
- Run or update the calculation. Confirm the selection and let NX calculate the properties. If the dialog offers an update, preview, or apply control, use it to refresh the reported values after selecting the geometry.
- Read the volume field. Locate “Volume” in the results. Check the displayed unit, which may be a cubic unit such as mm³, cm³, or in³. Record the number together with its unit; a bare number is not enough to use reliably.
- Set or confirm the unit system. If the unit is not what you need, use the command’s unit settings if available, or convert the result. For example, mm³ ÷ 1,000 = cm³, and mm³ ÷ 1,000,000,000 = m³. For inches cubed, use the exact conversion 1 in³ = 16,387.064 mm³.
- Check the scope of the answer. Verify whether the result refers to the selected body or the full selection. If you need a component’s volume inside an assembly, make sure you selected the intended component geometry rather than the entire assembly.
- Use the calculator as a cross-check when suitable. For a rectangular block, enter its length, width, and height in millimetres above and compare the calculated volume with NX. Do not use the rectangle calculator as a substitute for NX’s geometry-based result for an irregular or hollow part.
Common Mistakes
- Confusing volume with surface area. Surface area is measured in square units; volume is measured in cubic units. Make sure you copy the volume field, not area or mass.
- Mixing units. Multiplying dimensions in millimetres gives mm³. If one dimension is in inches and the others are in millimetres, convert first; the calculator does not detect mixed units.
- Using a bounding box as the actual volume. Multiplying overall length, width, and height gives a bounding-box volume. It is not the material volume of a curved, hollow, or irregular part.
- Selecting the wrong geometry. A face or sheet body does not represent a closed solid. Selecting several bodies can also produce a total when you wanted only one.
- Ignoring cavities or overlaps. Check whether pockets, holes, and separate bodies are modeled as intended. Overlapping bodies may be counted according to the selected geometry and operation, not according to what you meant the assembly to represent.
- Rounding too early. Keep the full value shown by NX for calculations and round only the final result to the precision your work requires.
Tips
- Write down the unit beside every result, such as 42,500 mm³, and preserve enough decimal places for downstream calculations.
- If you are comparing two versions of a part, use the same unit settings and selection scope for both measurements.
- For a hollow component, NX’s solid-body volume normally represents the modeled material, not the volume of the empty internal space. To determine cavity capacity, identify and measure the enclosed void separately.
- For a quick check on a simple rectangular model, compare NX’s result to length × width × height. A disagreement can reveal a unit mismatch or an incorrect selection.
- For a uniform material, mass can be estimated from volume and density, but density must match the material and units must be consistent. Volume alone does not determine mass.
Troubleshooting
- No volume appears: Confirm that you are using a solid-body measurement command and have selected a valid closed solid. A surface or sheet body may have area but no enclosed volume.
- The command will not accept your selection: Read the selection prompt and change the selection filter to bodies if needed. Clear the selection and try again, selecting the body rather than a face or feature.
- The result is zero or unexpectedly small: Check for a failed or suppressed feature, an open body, an extremely small model, or a unit mismatch. Zoom to the part and inspect its dimensions and body status.
- The result is unexpectedly large: Check whether multiple bodies or the whole assembly were selected. Confirm the unit shown in the results and verify that a bounding box was not mistaken for the modeled volume.
- Different NX versions show different menus: Search for the mass-properties command by name in the command finder and follow the current selection prompts. The command’s location can change, but the key requirement is to calculate properties for the intended solid body.
- The calculator does not match NX: Use it only for a rectangular solid, check that all entries are millimetres, and confirm that the model has the entered dimensions. Complex geometry requires NX’s body-based calculation.
Frequently Asked Questions
How do I calculate volume in NX?
Use the mass-properties or body-measurement command, select the intended solid body, and read the Volume result with its displayed cubic unit.
Can NX calculate the volume of an irregular shape?
Yes. A valid solid body can have curved or complex geometry; NX calculates volume from the modeled body rather than from three overall dimensions.
How do I calculate volume in cm³ from mm³?
Divide the value in mm³ by 1,000. For example, 100,000 mm³ equals 100 cm³.
Why does my part show no volume?
It may be a sheet or surface body rather than a closed solid, or the command may not have a valid body selection. Check the body type and selection prompt.
Does NX volume include holes and cavities?
Modeled holes and pockets are excluded from the material volume. The reported solid volume is not automatically the capacity of an enclosed cavity.
Can I get the volume of an assembly?
Usually, by selecting the relevant component bodies, but confirm which parts are included and whether the command reports a combined total. Avoid including unrelated or duplicate geometry.
Related
Formula used
in l | Length | mm | 100 | 0 in w | Width | mm | 50 | 0 in h | Height | mm | 20 | 0 out v | Volume | mm^3 | l * w * h | 2 out vl | Volume | cm^3 | v / 1000 | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Cubic Meters per Hour to Liters per Second0.2778 L/s