molecalculator

Moles & Molar Mass

Constant Volume: Meaning, Formula, and Examples

Calculator No. 01-5793 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This constant-volume calculator uses the amount of gas, its temperature change, and its initial pressure to calculate the final pressure when the volume stays fixed. Enter pressure in kilopascals and temperature in degrees Celsius; the result is the pressure after the temperature change, assuming the gas behaves ideally and the amount of gas does not change.

Formula

At constant volume, pressure is proportional to absolute temperature for a fixed amount of ideal gas. The formula is P₂ = P₁ × T₂ / T₁. Because temperatures are entered in degrees Celsius, convert each to kelvins by adding 273.15: P₂ = P₁ × (t₂ + 273.15) / (t₁ + 273.15).

  • P₁ is initial absolute pressure in kPa.
  • P₂ is final absolute pressure in kPa.
  • t₁ is initial temperature in °C; T₁ = t₁ + 273.15 is initial temperature in K.
  • t₂ is final temperature in °C; T₂ = t₂ + 273.15 is final temperature in K.

The calculator assumes a sealed, rigid container: its volume and the amount of gas remain unchanged. Pressure must be absolute, measured relative to a vacuum. If you start with gauge pressure, convert it before using the formula; near sea level, absolute pressure is approximately gauge pressure plus 101.325 kPa, though actual local atmospheric pressure can differ.

Worked Example

Using the calculator defaults, the initial absolute pressure is 101.325 kPa, the initial temperature is 20 °C, and the final temperature is 80 °C.

  1. Convert the initial temperature: T₁ = 20 + 273.15 = 293.15 K.
  2. Convert the final temperature: T₂ = 80 + 273.15 = 353.15 K.
  3. Substitute into the constant-volume relation: P₂ = 101.325 × 353.15 / 293.15 = 122.0699 kPa.
  4. Rounded to the calculator’s three decimal places, the final absolute pressure is 122.070 kPa.

The pressure rises because the gas is heated while its volume and quantity stay fixed. The result is absolute pressure, not gauge pressure.

Assumptions

  • The gas is treated as ideal, so its pressure, volume, amount, and absolute temperature obey the ideal gas law.
  • The container is rigid and sealed; neither its volume nor the amount of gas changes.
  • Temperatures are uniform throughout the gas and are converted from °C to K using 273.15.
  • Input pressure is absolute pressure in kPa. The calculator does not convert gauge pressure automatically.

What Constant Volume Means

Constant volume means that the space available to a substance does not change during the process being considered. In gas-law problems, it describes a fixed-volume condition, also called an isochoric or isovolumetric process. The terms are standard technical vocabulary, formed from roots meaning “same” and “volume”; they are not slang. A simple example is gas in a sealed, rigid tank: the container’s internal volume stays approximately fixed as the gas warms or cools.

Constant volume does not mean constant pressure or constant temperature. If a fixed amount of gas is heated in a rigid container, its pressure generally increases. If it is cooled, pressure generally decreases. For an ideal gas, the relationship follows from PV = nRT. When volume V and amount n do not change, P/T is constant, provided temperature is expressed in kelvins.

In a sentence: “The pressure in the rigid vessel increased as the gas heated at constant volume.” This phrase names a physical constraint or process condition; it is not, by itself, a special type of container or a claim that pressure remains unchanged.

How the Constant-Volume Relationship Works

At fixed volume and fixed amount of gas, the ideal gas law reduces to a proportional relationship between absolute pressure and absolute temperature. The final-to-initial ratio is:

P₂/P₁ = T₂/T₁

For example, increasing a gas’s kelvin temperature by a factor of 1.2 increases its absolute pressure by the same factor under these assumptions. A temperature increase of 20 °C is not automatically a 20% increase in pressure: the ratio depends on the starting temperature in kelvins. That is why the calculation converts both Celsius readings to kelvins before taking their ratio.

The equation is a form of the pressure law, often associated with Gay-Lussac’s law. Some textbooks use the name Amontons’ law for the pressure-temperature relationship. Naming conventions vary, but the important point is the condition: the amount of gas and volume are held fixed, and temperature is absolute.

When to Use It and How to Read the Result

Use this calculation when the gas is confined to a rigid volume and you know its starting pressure and temperature, as well as its final temperature. It can help with classroom gas-law exercises and estimates of how temperature changes affect pressure in sealed systems. It does not calculate a container’s volume, nor does it tell you how much heat is required to reach the final temperature.

Read the answer as the final absolute pressure in kPa. To compare it with a gauge-pressure reading, subtract the relevant local atmospheric pressure. For example, using 101.325 kPa as atmospheric pressure is an approximation appropriate to standard sea-level conditions, not a universal conversion. Do not compare a calculated absolute pressure directly with a gauge pressure without accounting for that difference.

For a process described as constant volume, the volume is unchanged between the stated initial and final conditions. In real equipment, containers can expand slightly, leak, or have temperature gradients. Those effects can make measured pressure differ from the ideal calculation.

Common Mistakes and Limits

  • Using Celsius in the ratio: Celsius has an arbitrary zero and cannot be used directly in P₂/P₁ = T₂/T₁. Add 273.15 to convert to kelvins.
  • Mixing absolute and gauge pressure: The gas-law equation requires absolute pressure. A gauge reading alone is not a valid P₁.
  • Assuming a flexible container has constant volume: A balloon or flexible bag changes volume as pressure and temperature change, so this calculator’s condition may not apply.
  • Ignoring leaks or chemical changes: If gas enters, escapes, condenses, or reacts, the amount or identity of gas may change. The simple proportional formula then needs reconsideration.

The ideal-gas approximation is most useful when gas particles are relatively far apart and intermolecular effects are small. At high pressures, near condensation, or for gases under conditions where non-ideal behavior matters, pressure may not scale exactly with temperature. A real vessel may also have a pressure rating that must not be exceeded. This calculator is an educational estimate, not a substitute for equipment specifications, engineering analysis, or a safety assessment.

Frequently Asked Questions

What is constant volume in simple terms?
It means the space occupied by the gas does not change during the process. In a rigid, sealed tank, heating the gas can raise its pressure even though the tank’s volume stays fixed.

What is the formula for pressure at constant volume?
For a fixed amount of ideal gas, P₁/T₁ = P₂/T₂, with pressure in absolute units and temperature in kelvins. Rearranged, P₂ = P₁ × T₂/T₁.

Can I use Celsius in a constant-volume gas-law calculation?
Not directly in the temperature ratio. Convert Celsius to kelvins by adding 273.15, then use the kelvin values.

Does constant volume mean constant pressure?
No. Constant volume only means the gas’s volume stays fixed. At constant volume, pressure changes in proportion to absolute temperature for a fixed amount of ideal gas.

Is constant volume the same as isochoric?
Yes. “Isochoric” is the standard technical adjective for a process at constant volume. “Isovolumetric” is another term used for the same condition.

Related

Formula used
in p1 | Initial absolute pressure | kPa | 101.325 | 0
in t1 | Initial temperature | °C | 20 | -273.15
in t2 | Final temperature | °C | 80 | -273.15
out p2 | Final absolute pressure | kPa | p1 * (t2 + 273.15) / (t1 + 273.15) | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →