Convert molality to molarity to express a solution’s concentration as moles of solute per liter of final solution rather than per kilogram of solvent. This calculator uses the solute’s molar mass and the solution’s density to estimate molarity; enter the molality in mol/kg, molar mass in g/mol, and density in g/mL.
Formula
Molality alone is not enough to determine molarity: the conversion depends on the mass of solute added and the volume occupied by the resulting solution. If density is known, calculate molarity using:
M = (m × ρ) / (1 + m × MM / 1000)
- M is molarity in mol/L.
- m is molality in mol/kg of solvent.
- ρ is the solution density in g/mL.
- MM is solute molar mass in g/mol.
The calculator’s expression converts the mass of solute in the denominator from grams to kilograms by dividing by 1000, and converts density from g/mL to g/L by multiplying by 1000. Equivalently, start with 1 kg of solvent: that sample contains m moles of solute, so its solute mass is m × MM grams. The total solution mass is therefore 1000 + m × MM grams. Divide this by density to obtain solution volume in mL, then convert mL to L by dividing by 1000. Molarity is moles divided by that volume in liters.
The second output, solution volume per kg solvent, is a checkable intermediate quantity. Its expression converts the solute mass from grams to kilograms, adds it to 1 kg of solvent, divides by density to get mL, and divides by 1000 to convert mL to L. The first output is the requested molarity.
Worked Example
Use the calculator’s defaults: molality = 1 mol/kg, molar mass = 58.44 g/mol, and solution density = 1.05 g/mL.
- Choose a basis of 1 kg of solvent. At 1 mol/kg, it contains 1 mol of solute.
- Find the solute mass: 1 mol × 58.44 g/mol = 58.44 g.
- Find total solution mass: 1000 g solvent + 58.44 g solute = 1058.44 g.
- Convert solution mass to volume using density: 1058.44 g ÷ 1.05 g/mL = 1008.038095 mL. In liters, 1008.038095 mL ÷ 1000 = 1.008038095 L.
- Divide solute moles by solution volume: 1 mol ÷ 1.008038095 L = 0.992025… mol/L.
Rounded to the calculator’s four decimal places, the molarity is 0.9920 mol/L. The solution volume per kg of solvent is 1.0080 L/kg.
Assumptions
- The stated density applies to the complete solution at the relevant temperature and concentration.
- The molality is based on kilograms of solvent, not kilograms of solution.
- The solution mass is the sum of solvent and solute masses; no material is lost or chemically consumed in a way that changes the stated composition.
- The calculated volume is the final solution volume inferred from density, not the starting solvent volume.
What You’ll Need
- The solution’s molality, in mol/kg.
- The solute’s molar mass, in g/mol. For a compound, obtain it from its formula and standard atomic weights, or a reliable reference.
- The solution density, in g/mL, measured or obtained for that composition and temperature. A solvent’s density is not a substitute for solution density.
- A calculator, or the calculator above.
Step-by-Step
- Check what your molality refers to. Molality, often written m, is moles of solute per kilogram of solvent. Confirm that the given value is not molarity, mass fraction, or moles per kilogram of total solution.
- Find the solute’s molar mass. Use the complete chemical formula and the appropriate atomic weights. For example, the value for sodium chloride is 58.44 g/mol. Use the formula for the actual solute, including any waters of hydration when applicable.
- Find the solution density. Use density for the solution at its concentration and temperature, in g/mL. If the value is in kg/L, it has the same numerical value as g/mL; if it is in g/L, divide by 1000. Do not assume density is exactly 1 g/mL unless that approximation is justified.
- Enter all three values. Input molality in mol/kg, molar mass in g/mol, and density in g/mL. Check decimal places and units before calculating.
- Read the molarity result. The main answer is in mol/L, also called M. The additional output is the estimated liters of solution corresponding to 1 kg of solvent, useful for checking the conversion.
- Keep appropriate precision. Report no more significant figures than the least precise input supports. The displayed decimals are formatting, not a claim that the measurements are exact.
Common Mistakes
- Using solvent density instead of solution density. The formula needs the density of the finished solution. The solute generally changes both total mass and volume.
- Confusing molality and molarity. Molality uses kilograms of solvent; molarity uses liters of solution. They are not interchangeable, even when their numerical values happen to be close.
- Using the wrong molar mass. Check the compound formula, hydration state, and units. A molar mass entered in kg/mol instead of g/mol is off by a factor of 1000.
- Mixing density units. Enter g/mL. Although kg/L has the same numerical value, g/L does not.
- Assuming volume is additive. The final solution volume is not necessarily the solvent volume plus a separately estimated solute volume. Use solution density or a directly known final volume.
- Rounding too early. Keep extra digits through the volume calculation and round only the final reported molarity.
Tips
- For a quick reasonableness check, compare molarity with molality. They may be similar for dilute aqueous solutions, but they need not match; the formula accounts for solute mass and solution density.
- Write the units beside each number before substituting. The final operation must be moles divided by liters.
- If density is available in a table, verify that its temperature and concentration match your solution. Density can change with both.
- For a highly concentrated solution, prefer measured or authoritative density data over a rough approximation. Small density errors can noticeably affect the result.
- For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.
Troubleshooting
- The answer seems about 1000 times too large or too small: check whether you entered density in g/L rather than g/mL, or molar mass in kg/mol rather than g/mol. Convert units before entering them.
- You do not know the density: molality and molar mass alone cannot uniquely determine molarity. Find density for the solution’s composition and temperature, measure it using an appropriate lab method, or use a directly known final volume and mass basis instead. Do not present an assumed density as an exact result.
- The calculated value differs from a reference: compare the density, temperature, molar mass convention, and rounding used. Also check whether the reference reports molality or molarity.
- The density value looks implausible: confirm its unit and whether it describes the solution or pure solvent. If it is a volume-based concentration table, check its stated temperature and composition.
- The inputs are correct but the last digits differ: this is usually rounding. Retain full precision in intermediate steps and compare results at the same number of significant figures.
Frequently Asked Questions
Can I convert molality to molarity without density?
No, not from molality and molar mass alone. You need solution density, or enough independent information to determine the final solution volume.
Why does the formula include molar mass?
Molality is based on solvent mass, but density applies to total solution mass. Molar mass lets you calculate how much solute mass is added for a chosen amount of solvent.
Are molality and molarity ever equal?
They can be numerically close for some dilute solutions, but equality is not guaranteed. The relationship depends on solute molar mass and solution density.
What if density is reported in kg/L?
Enter the same numerical value as g/mL: 1 kg/L equals 1 g/mL. Convert g/L by dividing by 1000 before entering it.
Does temperature matter?
Yes. Density, and therefore the conversion to molarity, can vary with temperature. Use density at the temperature relevant to the stated solution volume.
Can I use solvent volume instead of final solution volume?
No. Molarity is moles per liter of final solution. The conversion uses solution density to infer that final volume.
Related
Formula used
in b | Molality | mol/kg | 1 | 0 in mm | Solute molar mass | g/mol | 58.44 | 0.001 in d | Solution density | g/mL | 1.05 | 0.001 out c | Molarity | mol/L | b * d / (1 + b * mm / 1000 / 1000) * 1000 | 4 out vm | Solution volume per kg solvent | L/kg | (1000 + b * mm / 1000) / d / 1000 | 4
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- MD Calc I:T Ratio Calculator and Explanation0.0500 ratio
- Oxygen Mass Number: Isotope Values Explained16 nucleons
- Mass-to-Light Ratio: Meaning and Calculation1.000 M☉/L☉
- M/z Ratio in Mass Spectrometry: Meaning and Calculation1,000.00 Th
- Mass Fraction to Molar Fraction Calculator
- K2 Molar Mass Calculator and Calculation78.1966 g/mol