This calculator finds the molarity of a solution from the mass and molar mass of its solute and the final solution volume. Enter those three values to get concentration in mol/L and mM; use the steps below to check the inputs and interpret the answer.
Formula
Molarity is the amount of solute, in moles, divided by the final volume of solution, in liters:
C = n / V = (m / M) / (VmL / 1000)
- C is molar concentration in mol/L, also written M.
- n is amount of solute in moles.
- m is solute mass in grams.
- M is the solute’s molar mass in g/mol.
- VmL is the final solution volume in milliliters. Dividing by 1000 converts mL to L.
The conversion to millimolar is CmM = C × 1000, because 1 mol/L equals 1000 mmol/L, or 1000 mM. The calculator assumes the mass is pure solute and the stated volume is the volume of the completed solution, not the amount of solvent used.
Worked Example
Using the calculator’s default values—2.922 g solute, 58.44 g/mol molar mass, and 250 mL final solution volume:
- Find the amount in moles: n = 2.922 g / 58.44 g/mol = 0.050000 mol.
- Convert the final volume to liters: V = 250 mL / 1000 = 0.250 L.
- Divide moles by liters: C = 0.050000 mol / 0.250 L = 0.2000 mol/L.
- Convert to millimolar: 0.2000 mol/L × 1000 = 200.00 mM.
The calculator reports 0.2000 mol/L and 200.00 mM, rounded to the displayed decimal places. The extra digits in intermediate calculations help avoid rounding too early; they do not imply that the measured mass or volume is perfectly precise.
Assumptions
- The solute’s stated mass is the mass of the chemical whose molar mass is entered; purity, water content, and impurities are not corrected.
- The measured volume is the final volume of the entire solution.
- The solution is treated as a mixture for concentration arithmetic; no assumption about dissociation or chemical reaction is needed to calculate formal molarity.
- Temperature-related volume changes and measurement uncertainty are not included.
What You’ll Need
- The solute’s mass, measured in grams, or a reliable conversion from the unit on its label.
- The correct molar mass in g/mol. Calculate it from the compound’s formula and atomic weights, or use a reliable reference. For example, the standard atomic weights Na = 22.990 and Cl = 35.45 give NaCl a molar mass of 58.44 g/mol.
- The final solution volume in mL or L, measured or specified for the completed solution.
- A calculator or the calculator above. For bench work, use suitable measuring equipment and personal protective equipment for the substance.
Step-by-Step
- Identify the concentration type. This page calculates molarity, which is moles of solute per liter of solution. It does not directly calculate mass concentration (such as g/L), percent concentration, or molality (moles per kilogram of solvent). Check that molarity is the quantity you need.
- Confirm the substance and formula. Use the molar mass for the exact chemical form, including any waters of hydration if the material is a hydrate. An anhydrous compound and its hydrate have different molar masses, so the same weighed mass represents different amounts in moles.
- Record the solute mass in grams. Convert from milligrams by dividing by 1000, or from kilograms by multiplying by 1000. Keep the unrounded value available until the final calculation. If you are starting with a known number of moles instead of a mass, use C = n / V directly.
- Enter the molar mass in g/mol. Check both the numerical value and its units. If calculating it from a molecular formula, multiply each element’s atomic weight by its count in the formula, then add those contributions. Do not use the mass of just one atom when the solute is a compound.
- Enter the final solution volume. The calculator accepts mL and converts it to liters by dividing by 1000. If your volume is already in liters, multiply by 1000 before entering it. Do not enter the volume of solvent before dissolving the solute: adding solute can change the total volume.
- Calculate and check the result. Compare the displayed value with the formula. A larger amount of solute raises molarity; a larger final volume lowers it. Confirm that the result’s units are mol/L and that the mM value is exactly 1000 times the mol/L value, apart from displayed rounding.
- Report precision responsibly. Round only after calculating, and match the reported significant figures to the least precise measured input. State the concentration unit and, when relevant, the temperature or preparation conditions used for the volume.
For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.
Common Mistakes
- Using solvent volume instead of final volume: Molarity uses the volume after the solute is dissolved and the solution is brought to its final volume.
- Mixing up grams and milligrams: A 1000-fold mass-unit error creates a 1000-fold concentration error.
- Entering the wrong molar mass: Check the formula, hydrate state, and units. A value in g/mol is needed, not a molecular weight entered in another unit.
- Confusing M and mM: 1 M = 1000 mM. A value of 0.2 M is 200 mM, not 0.2 mM.
- Rounding too early: Keep extra digits during intermediate steps and round the final result to reflect the precision of the inputs.
- Assuming mass concentration is molarity: A result in g/L cannot be labeled mol/L unless it is divided by the solute’s molar mass in g/mol.
Tips
- Write units beside every measurement before substituting values. Units help reveal whether a conversion has been missed.
- Use the chemical formula and the appropriate molar mass for the exact form of the reagent. For a hydrate, include the waters shown in its formula.
- Use the actual final volume for a prepared solution. If a protocol specifies a volumetric flask, follow its stated method rather than estimating from the starting solvent volume.
- Keep unrounded measurements and calculations in your notes. Show the final concentration with its unit and sensible significant figures.
- If only mass and final volume are known and you need g/L instead, calculate mass in grams divided by volume in liters; that is a different concentration measure from molarity.
Troubleshooting
- The result is 1000 times too large or small: Check whether you entered mL where the calculator expects mL, and confirm that grams were not confused with milligrams. The volume conversion is mL / 1000 to obtain liters.
- The answer seems chemically implausible: Verify the solute formula, molar mass, hydrate state, mass, and final volume. Recalculate the moles separately as mass divided by molar mass.
- You do not know the final volume: You cannot calculate a reliable molarity from mass alone. Obtain the final solution volume from the method or measurement; do not substitute an estimated solvent volume without stating that limitation.
- Your inputs are in different units: Convert mass to grams and volume to milliliters before entering them. Record each conversion so it can be checked.
- The displayed value differs slightly from your hand calculation: Check whether your hand calculation rounded an intermediate value or used a different molar mass. Compare unrounded values first, then apply the same rounding.
Frequently Asked Questions
What is the basic formula for solution concentration?
Molarity is C = n / V: moles of solute divided by final solution volume in liters. If you know mass, find moles using n = mass / molar mass.
Can I calculate concentration from mass and volume alone?
You can calculate mass concentration, such as g/L, from mass and volume. To calculate molarity, you also need the solute’s molar mass, unless the amount in moles is already known.
Does molarity use the volume of solvent?
No. It uses the final volume of the whole solution after the solute is dissolved. Solvent volume and final solution volume are not necessarily equal.
How do I convert mol/L to mM?
Multiply mol/L by 1000. For example, 0.025 mol/L is 25 mM.
What if the solute is a hydrate?
Use the molar mass for the hydrated formula shown for the substance. Using the anhydrous molar mass would give an incorrect number of moles for the weighed hydrate.
Does this formula account for purity or temperature?
No. It uses the entered mass and final volume as given. For impure material, use a validated purity correction if appropriate; for precise work, follow the method’s temperature and measurement requirements.
Related
Formula used
in m | Mass of solute | g | 2.922 | 0 in mm | Molar mass | g/mol | 58.44 | 0.001 in v | Final solution volume | mL | 250 | 0.001 out c | Molarity | mol/L | m / mm / (v / 1000) | 4 out cmm | Concentration in millimolar | mM | c * 1000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Cubic Meters per Hour to Liters per Second0.2778 L/s