molecalculator

Moles & Molar Mass

If Volume Decreases What Happens to Pressure

Calculator No. 01-12510 · Updated · Formula and assumptions shown below

Final pressure 2.000 atm
Initial pressure
1 atm
Set in the form below
Initial volume
2 L
Set in the form below
Final volume
1 L
Set in the form below
You enter
Initial pressure (atm), Initial volume (L), Final volume (L)
You get
Final pressure (atm)
Rounding
3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

If volume decreases while the amount of gas and its temperature stay constant, the pressure increases. This is the core of Boyle’s law, which states that for a fixed mass of gas at constant temperature, pressure and volume are inversely proportional. In practical terms, squeezing a gas into a smaller space makes its particles hit the container walls more often, raising the pressure.

Formula

Boyle’s law is written as:

P₁V₁ = P₂V₂

Where:

  • P₁ = initial pressure (atm, kPa, mmHg, etc.)
  • V₁ = initial volume (L, mL, m³, etc.)
  • P₂ = final pressure (same unit as P₁)
  • V₂ = final volume (same unit as V₁)

The formula works with any consistent pressure and volume units, as long as you don’t mix them. To solve for final pressure, rearrange to:

P₂ = P₁ × V₁ / V₂

This calculator uses atmospheres and liters by default, but you can enter any pressure and volume units as long as you keep them consistent.

Worked Example

Suppose a gas occupies 2.0 L at 1.0 atm. If the volume is reduced to 1.0 L at constant temperature, what is the new pressure?

Using the formula:

P₂ = P₁ × V₁ / V₂ = 1.0 atm × 2.0 L / 1.0 L = 2.0 atm

So halving the volume doubles the pressure. The calculator above gives the same result (2.000 atm).

Assumptions

  • The gas behaves as an ideal gas (no intermolecular forces, negligible particle volume).
  • The temperature remains constant.
  • The amount of gas (number of moles) does not change.
  • The gas is confined in a flexible or rigid container that allows volume change.

Why Does Pressure Increase When Volume Decreases?

Gas pressure comes from particles colliding with the walls of their container. When you shrink the volume, the same number of particles now occupies less space, so they travel a shorter distance between wall collisions. This means:

  • More collisions per second on each unit area of the wall.
  • Each collision transfers momentum to the wall, producing force.
  • The total force per unit area (pressure) therefore increases.

Think of a crowded elevator: if the same number of people are squeezed into half the space, they bump into the walls and each other much more often. Gas particles behave the same way, except they are moving at hundreds of meters per second.

Real-World Examples

Boyle’s law appears everywhere:

  • Syringes: Pulling the plunger increases volume, lowering pressure and drawing liquid in. Pushing the plunger decreases volume, raising pressure and expelling liquid.
  • Scuba diving: As a diver descends, water pressure increases, compressing the air in the lungs and in the tank. A full tank at the surface delivers less air at depth because the same mass of gas occupies a smaller volume.
  • Bicycle pump: Compressing the air in the pump barrel reduces its volume, increasing pressure until it exceeds the tire’s internal pressure and forces air in.
  • Breathing: Your diaphragm expands the chest cavity (increasing volume, decreasing pressure), pulling air into the lungs. Exhaling reverses the process.

Common Mistakes and Misconceptions

One frequent error is forgetting that Boyle’s law only applies when temperature and the number of gas particles are constant. If you compress a gas quickly, it heats up (as in a diesel engine’s compression stroke), so the simple inverse relationship no longer holds. In that case, you need the combined gas law or the ideal gas law.

Another mistake is mixing units. For example, if you start with pressure in atmospheres and volume in liters, you must use the same units on both sides. Converting 100 kPa to atm (divide by 101.325) before plugging in avoids errors.

A common misconception is that pressure increases because the particles themselves get “more energetic.” That is not true at constant temperature—the average kinetic energy of the particles stays the same. The increase in pressure comes purely from more frequent collisions, not harder ones.

When Does Boyle’s Law Fail?

Real gases deviate from ideal behavior at very high pressures and very low temperatures. Under those conditions, intermolecular attractions become significant, and the finite size of molecules matters. For example, at 200 atm, the measured pressure of a gas can be noticeably different from the Boyle’s law prediction. The van der Waals equation corrects for these effects, but for most everyday and laboratory situations at moderate pressures (up to a few atmospheres), Boyle’s law is accurate to within a few percent.

Also, if the container is not sealed, gas can escape during compression, changing the number of moles. Boyle’s law assumes a closed system.

Frequently Asked Questions

Does pressure double if volume is halved?

Yes, if temperature and the amount of gas are constant. Halving the volume makes the gas particles collide with the walls twice as often, so pressure doubles. This is a direct consequence of P₁V₁ = P₂V₂.

What happens to pressure if volume decreases but temperature increases?

It depends on the relative changes. If you compress a gas and also heat it, pressure will increase even more than Boyle’s law predicts. The combined gas law (P₁V₁/T₁ = P₂V₂/T₂) accounts for both changes. For example, compressing a gas to half its volume while doubling its absolute temperature would quadruple the pressure.

Why does a balloon pop when you squeeze it?

Squeezing reduces the volume of the balloon, increasing the pressure of the air inside. The rubber stretches until it can no longer withstand the force, eventually tearing. The pressure increase follows Boyle’s law, but the balloon’s elasticity limits how much pressure it can hold.

What is the difference between Boyle’s law and Charles’s law?

Boyle’s law relates pressure and volume at constant temperature. Charles’s law relates volume and temperature at constant pressure. In Charles’s law, if temperature increases, volume increases proportionally (at constant pressure). Both are special cases of the ideal gas law.

Can Boyle’s law be used for liquids?

No, Boyle’s law applies to gases. Liquids are nearly incompressible—their volume changes very little even under large pressures. For example, water only compresses by about 0.005% per atmosphere of pressure, so the inverse relationship does not apply.

How do I convert pressure units when using Boyle’s law?

You don’t need to convert if you keep the same unit on both sides. For instance, if P₁ is in mmHg, then P₂ will also be in mmHg. If you need the answer in a different unit, convert after calculating. Use the conversion factors: 1 atm = 101.325 kPa = 760 mmHg = 14.696 psi.

Related

Formula used
in p1 | Initial pressure | atm | 1.0 | 0
in v1 | Initial volume | L | 2.0 | 0
in v2 | Final volume | L | 1.0 | 0
out p2 | Final pressure | atm | p1 * v1 / v2 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →