molecalculator

Moles & Molar Mass

Molarity: Moles per Liter Explained

Calculator No. 01-4811 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Yes. Molarity is the amount of solute in moles divided by the final volume of the solution in liters, commonly written M = n/V. This calculator finds molarity from a solute’s mass, its molar mass, and the final solution volume, and also reports the concentration in millimolar.

Formula

Molarity is moles of solute divided by final solution volume: M = n/V. Here, M is molarity in mol/L, n is amount of solute in moles, and V is the total volume of the solution in liters. If the solute amount is given as a mass, first calculate n = m/mm, where m is mass in grams and mm is molar mass in g/mol. With volume entered in milliliters, the calculator uses M = (m/mm)/(v/1000), because 1 L = 1000 mL. Millimolar concentration is mM = M × 1000.

Worked Example

Using the calculator’s default values—2.922 g solute, a molar mass of 58.44 g/mol, and a final volume of 250 mL—first find the amount in moles:

n = 2.922 g / 58.44 g/mol = 0.050000 mol

Convert the final volume to liters:

V = 250 mL / 1000 = 0.25000 L

Then divide moles by liters:

M = 0.050000 mol / 0.25000 L = 0.2000 mol/L

Convert to millimolar:

0.2000 mol/L × 1000 = 200.00 mM

The displayed results are therefore 0.2000 mol/L and 200.00 mM. The chosen molar mass, 58.44 g/mol, is approximately the molar mass of sodium chloride from standard atomic weights; the calculation itself does not assume that the solute is sodium chloride.

Assumptions

  • The entered mass is the mass of pure solute, and the molar mass matches its chemical formula and form.
  • The volume is the final volume of the entire solution, not the amount of solvent initially measured.
  • The calculation reports analytical concentration from the stated quantities. It does not account for chemical reactions, ion pairing, activity effects, or volume changes after preparation.

What Molarity Measures

Molarity expresses concentration as moles per unit volume of solution. One mole represents a defined amount of entities—such as molecules, atoms, or formula units—rather than a particular mass. Molar mass connects the two: dividing grams by grams per mole gives moles. Dividing those moles by liters then gives mol/L.

For example, a 0.2000 M solution contains 0.2000 mol of the specified solute in each liter of solution. It does not mean 0.2000 mol is present in every container: a 100 mL portion at that concentration contains 0.02000 mol, because 100 mL is one tenth of a liter. In general, the amount in a sample is n = M × V, with volume expressed in liters.

Molarity is also called amount concentration or, informally, molar concentration. The symbol M is widely used as a unit shorthand: 1 M = 1 mol/L. Writing mol/L is often clearer in formal calculations because it makes the units explicit.

How to Use the Calculator

  1. Enter the solute mass in grams.
  2. Enter the compound’s molar mass in g/mol. For a pure compound, obtain it by adding the atomic masses in its chemical formula, accounting for each subscript.
  3. Enter the final solution volume in milliliters. Use the total volume after the solute is included, not just the volume of solvent.
  4. Read the result in mol/L. The second output gives the same concentration in mM, where 1 mM = 0.001 mol/L.

The calculator is useful for translating a weighed mass into concentration, checking a concentration calculation, or comparing values expressed in M and mM. For instance, the formula also rearranges to m = M × V × mm when you need to calculate the mass corresponding to a target molarity, volume, and molar mass. That rearrangement is a planning calculation, not a substitute for a specified laboratory method.

Common Mistakes and Limits

  • Using milliliters as if they were liters: convert mL to L by dividing by 1000. A missing conversion changes the answer by a factor of 1000.
  • Using solvent volume instead of final solution volume: molarity is based on the volume of the complete solution. Adding solute can change the total volume.
  • Mixing up mass and amount: grams are not moles. Divide mass by the correct molar mass before applying M = n/V.
  • Choosing the wrong chemical form: hydrates, salts, and compounds with different formulas have different molar masses. Check the stated formula and whether the material’s purity or hydration state matters.
  • Rounding too early: keep guard digits through the calculation and round the final result to a precision justified by the input measurements.

Molarity is based on volume, so it can vary with temperature when a solution expands or contracts. For many routine calculations this effect is small, but precise work should use the volume and temperature specified by the method. Molarity also describes the formal amount concentration; it does not by itself tell you the concentration of each species after an equilibrium or reaction. If a solute dissociates, the molarity of the original formula units is not automatically the molarity of every resulting ion.

For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor. This calculator is for general chemistry arithmetic, not for preparing materials for administration to people or animals.

Frequently Asked Questions

Is molarity moles divided by volume?
Yes: M = n/V. The volume must be the solution’s final volume in liters, so the usual unit is mol/L.

Do I use milliliters or liters for molarity?
Use liters in the formula. If volume is recorded in milliliters, divide it by 1000 before calculating molarity.

What is the difference between molarity and moles?
Moles measure the amount of solute. Molarity measures that amount per volume, so the same number of moles can have different molarities in different solution volumes.

Is M the same as mol/L?
Yes. The symbol M is commonly used to mean molar, or moles per liter: 0.5 M equals 0.5 mol/L.

Can I calculate moles from molarity?
Yes. Rearrange the formula to n = M × V. Use mol/L for molarity and liters for volume to obtain moles.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →