molecalculator

Moles & Molar Mass

Liquid Oxygen Expansion Ratio: Liquid to Gas Volume

Calculator No. 01-3390 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The liquid oxygen expansion ratio is about 860:1: one volume of liquid oxygen produces roughly 860 volumes of oxygen gas when it warms to about 20 °C and 1 atmosphere. This calculator estimates the gas volume from a liquid volume, or the liquid volume needed for a target gas volume, using that approximate ratio.

Formula

For gas volume from liquid volume, multiply the liquid oxygen volume by the approximate expansion ratio: Vgas = Vliquid × 860. For liquid volume from gas volume, divide instead: Vliquid = Vgas ÷ 860.

  • Vliquid is liquid oxygen volume in liters (L).
  • Vgas is oxygen gas volume in liters (L), at the reference conditions described below.
  • 860 is the approximate liquid-to-gas volume ratio, expressed as liters of gas per liter of liquid.

Choose “Gas from liquid” to use the first equation; choose “Liquid from gas” to use the second. The calculator shows the calculated volume in liters and the ratio it uses. This simple conversion assumes the gas is measured near 20 °C and 1 atm. It is a planning estimate, not a substitute for a pressure or cryogenic-system calculation.

Worked Example

Using the defaults, the selected mode is “Gas from liquid,” with 1 L of liquid oxygen:

Vgas = 1 L × 860 = 860 L

The calculator reports 860.000 L of oxygen gas. The inverse calculation is also useful: 860 L of gas ÷ 860 = 1 L of liquid oxygen. These figures illustrate the approximate ratio; they do not account for changes in temperature, pressure, evaporation losses, or equipment conditions.

Assumptions

  • The ratio is approximately 860 liters of oxygen gas per liter of liquid oxygen.
  • The gas-volume reference is approximately 20 °C and 1 atm (101.325 kPa).
  • Oxygen is treated as an ideal gas for this approximate conversion.
  • The calculation concerns volume equivalence only; it does not predict boil-off rate, delivery pressure, or usable oxygen after losses.

What the Expansion Ratio Means

Oxygen is a gas at ordinary room conditions. Cooling it below its boiling point, about −183 °C at atmospheric pressure, condenses it into a cryogenic liquid. The molecules are then packed much more closely than in the gas. When the liquid warms and vaporizes, the same amount of oxygen occupies far more space as gas.

An expansion ratio compares those two volumes for the same amount of substance. A ratio near 860:1 means that a liter of liquid becomes approximately 860 liters of gas under the stated reference conditions. It does not mean oxygen expands by the same amount under every condition: a gas volume depends strongly on its temperature and pressure.

“One liter becomes 860 liters” is therefore shorthand. The liquid does not create additional oxygen; its molecules change phase and spread out. The gas volume must always be tied to a temperature and pressure to be meaningful.

Why the Number Varies

Published figures commonly fall around 850–860 volumes of gas per volume of liquid, because sources may use different reference temperatures, pressures, and liquid-density values. The calculator uses 860 as a convenient approximate value, not a universal constant. For precise engineering or inventory work, use the property data and reference conditions specified for the particular system.

For a fixed amount of gas, warming it or lowering its pressure increases its volume. Cooling it or raising its pressure decreases its volume. In an ideal-gas approximation, volume at a new condition can be estimated from the combined gas law:

V2 = V1 × (T2/T1) × (P1/P2)

Here temperature must be in kelvins and pressure must use the same units in both terms. This relation adjusts a gas volume after vaporization; it does not model the liquid’s density change or detailed behavior near condensation.

Using the Estimate and Avoiding Misinterpretation

The ratio is useful for quick comparisons of liquid inventory with a potential gas volume, or for understanding why small quantities of cryogenic liquid can create substantial gas volumes. For example, 10 L of liquid oxygen corresponds approximately to 8,600 L of gas at the stated reference conditions. Conversely, 1,000 L of gas corresponds to about 1.16 L of liquid (1,000 ÷ 860).

  • Keep units consistent: the ratio works with matching volume units, such as liters to liters or cubic meters to cubic meters.
  • State the gas temperature and pressure when reporting a volume. A volume without conditions is incomplete.
  • Do not confuse expansion ratio with a pressure ratio. The factor 860 relates volumes across a phase change, not pressures.
  • Do not assume the entire theoretical gas volume is immediately available in a real installation; heat transfer, venting, pressure regulation, and residual liquid affect actual delivery.

At 20 °C and 1 atm, 860 L of ideal oxygen gas occupies about 0.86 m³. If the same oxygen is confined, it can produce a dangerous pressure as it warms and vaporizes. The expansion figure alone cannot be used to size a vessel, relief device, room ventilation, or gas supply system.

Safety and Scope

Liquid oxygen is an extremely cold oxidizer. Contact can cause severe cold injury, while oxygen-enriched surroundings make materials ignite more easily and burn more intensely. Oxygen itself is not a fuel, but it greatly increases fire risk. Keep it away from oil, grease, fuels, and incompatible materials, and use only equipment designed and approved for oxygen service.

Never seal liquid oxygen in an ordinary container or assume that a closed vessel can safely accommodate vaporization. Cryogenic systems need suitable pressure relief and must be handled by trained personnel under applicable procedures. This calculator is for general volume estimation only; it is not operating guidance or a design tool. Consult the relevant safety data sheet and qualified safety or engineering personnel for actual handling and system decisions.

Frequently Asked Questions

How many liters of gas come from 1 liter of liquid oxygen?
Approximately 860 L of oxygen gas at about 20 °C and 1 atm. The exact figure depends on the reference conditions and property data used.

What is the expansion ratio of liquid oxygen at standard temperature and pressure?
There is no single value unless “standard” conditions are defined. Around 850–860:1 is commonly cited, while this calculator uses 860:1 for gas near 20 °C and 1 atm.

How much liquid oxygen is equivalent to 1,000 liters of gas?
Using 860:1, 1,000 L ÷ 860 is about 1.16 L of liquid oxygen. Treat this as an approximate volume equivalence, not a delivery or storage guarantee.

Does liquid oxygen expand 860 times in every container?
No. The ratio compares liquid volume with gas volume at specified conditions. A container’s pressure, temperature, design, and venting determine what happens in practice.

Is oxygen flammable?
Oxygen is not itself a fuel, but it supports combustion. Oxygen-enriched conditions can make fires start more easily and burn much more fiercely, so contamination and ignition sources require strict control.

Related

Formula used
in vl | Liquid oxygen volume | L | 1 | 0
in vg | Oxygen gas volume | L | 860 | 0
sel mode | Calculate | Gas from liquid=1, Liquid from gas=2
out result | Calculated volume | L | (vl * 860 / (1 + (mode - 1) * 859) + vg * (mode - 1) / (1 + (mode - 1) * 859)) | 3
out ratio | Expansion ratio used | L gas/L liquid | 860 | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →