molecalculator

Moles & Molar Mass

Molar Mass of Copper(II) Sulfate: Exact Value & How to Find It

Calculator No. 01-7395 · Updated · Formula and assumptions shown below

Molarity 0.0732 mol/L
Concentration in millimolar
73.23 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
159.61 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The molar mass of anhydrous copper(II) sulfate (CuSO₄) is 159.61 g/mol. For the common hydrated form, copper(II) sulfate pentahydrate (CuSO₄·5H₂O), the molar mass is 249.69 g/mol. This article explains how these values are calculated, why the hydrate matters in the lab, and how to use molar mass in real calculations.

Formula

The molar mass (M) of a compound is the sum of the atomic masses of all atoms in its chemical formula. For copper(II) sulfate:

M(CuSO₄) = Ar(Cu) + Ar(S) + 4 × Ar(O)

For the pentahydrate, add five water molecules:

M(CuSO₄·5H₂O) = Ar(Cu) + Ar(S) + 4 × Ar(O) + 5 × [2 × Ar(H) + Ar(O)]

Using IUPAC standard atomic weights (Cu = 63.546, S = 32.06, O = 15.999, H = 1.008):

  • CuSO₄: 63.546 + 32.06 + 4(15.999) = 159.61 g/mol
  • CuSO₄·5H₂O: 159.61 + 5(18.015) = 249.69 g/mol

The calculator above uses the molar mass you input (default 159.61 g/mol) to convert a given mass of solute into moles and then into molarity when you specify a final solution volume.

Worked Example

Suppose you need to prepare 250 mL of a 0.0732 mol/L copper(II) sulfate solution using anhydrous CuSO₄ (molar mass 159.61 g/mol). How many grams do you weigh out?

  1. Convert volume to liters: 250 mL ÷ 1000 = 0.250 L
  2. Calculate moles needed: moles = molarity × volume = 0.0732 mol/L × 0.250 L = 0.01830 mol
  3. Convert to mass: mass = moles × molar mass = 0.01830 mol × 159.61 g/mol = 2.921 g

So you weigh 2.922 g of anhydrous CuSO₄, dissolve in water, and dilute to exactly 250 mL. The calculator gives the same result: entering m = 2.922, mm = 159.61, v = 250 yields c = 0.0732 mol/L.

Assumptions

  • The compound is pure and anhydrous (no water of hydration) unless stated otherwise.
  • The molar mass is based on IUPAC standard atomic weights; commercial reagents may have slight impurities.
  • Final volume is used, not solvent volume – you dissolve then top up to the mark.
  • Solution is dilute and at room temperature; density changes are negligible for this calculation.

Why Does the Hydrate Form Matter?

Copper(II) sulfate is commonly sold as the bright blue pentahydrate (CuSO₄·5H₂O) because it is more stable and easier to crystallize. The anhydrous form is a pale greenish-white powder that readily absorbs water from air. If you weigh out 159.61 g of the pentahydrate, you are actually weighing 159.61 g of CuSO₄ plus 90.08 g of water – so you would only have 63.9% of the copper sulfate you intended. This is a classic lab pitfall: using the wrong molar mass leads to a ~57% error in concentration.

To convert between the two, use the factor: mass of CuSO₄ = mass of pentahydrate × (159.61 / 249.69) = 0.6393 × mass of pentahydrate. Conversely, to get a certain mass of anhydrous CuSO₄ from the hydrate, multiply by 1.564.

How to Use Molar Mass in Solution Preparation

The most common use of molar mass is to prepare a solution of known molarity. The steps are:

  1. Decide the desired concentration (c, mol/L) and final volume (V, L).
  2. Calculate moles: n = c × V.
  3. Calculate mass: m = n × M, where M is the molar mass of the actual compound you weigh.
  4. Weigh the solid, dissolve in a beaker with less than final volume of water, transfer to a volumetric flask, and add water to the mark.

For example, to make 500 mL of 0.1 mol/L CuSO₄ using the pentahydrate: n = 0.1 × 0.5 = 0.05 mol; m = 0.05 × 249.69 = 12.48 g. If you mistakenly used the anhydrous mass (159.61), you would add only 7.98 g – a 36% error.

Common Mistakes and Misconceptions

  • Confusing hydrate and anhydrous: Always check the label. The pentahydrate is blue; anhydrous is off-white.
  • Forgetting to convert mL to L: Molarity is mol/L, so 250 mL must be 0.250 L.
  • Using atomic mass in grams instead of g/mol: The units are the same numerically, but the concept is per mole.
  • Rounding too early: Use at least 4 significant figures in intermediate steps to avoid errors.
  • Assuming the hydrate is 100% pure: Reagent-grade hydrate may have slight moisture content; dry it if exact concentration is critical.

Other Applications of Molar Mass

Beyond solution prep, molar mass is used in:

  • Stoichiometry: Converting masses of reactants to moles to find limiting reagents.
  • Percent composition: Calculating the mass percentage of each element in the compound.
  • Electrochemistry: Relating charge passed to mass deposited in copper plating (Faraday’s law).
  • Dilution calculations: When preparing standards from a stock solution, you often need to know the molar mass to compute the stock concentration.

Safety and Handling

Copper(II) sulfate is harmful if swallowed and can irritate skin and eyes. It is toxic to aquatic life. Wear gloves and safety goggles when handling the powder or solutions. Avoid inhaling dust – use a fume hood if weighing large amounts. In case of contact, rinse with plenty of water. For lab work, always follow your institution’s safety data sheet (SDS) and your supervisor’s instructions. Dispose of copper solutions as hazardous waste, not down the drain.

Frequently Asked Questions

What is the molar mass of CuSO₄·5H₂O?

The molar mass is 249.69 g/mol. This includes five water molecules (each 18.015 g/mol) attached to the copper sulfate unit (159.61 g/mol).

Why is the molar mass of copper sulfate sometimes listed as 159.6 and sometimes 249.7?

The difference is the hydration state. Anhydrous CuSO₄ has no water (159.61 g/mol), while the pentahydrate has five water molecules (249.69 g/mol). Always check the chemical formula on the bottle.

How many grams of CuSO₄ are in 100 g of CuSO₄·5H₂O?

Use the ratio: 100 g × (159.61 / 249.69) = 63.93 g of anhydrous CuSO₄. The remaining 36.07 g is water of crystallization.

What is the oxidation state of copper in copper(II) sulfate?

Copper is in the +2 oxidation state, which gives the compound its name. The sulfate ion is SO₄²⁻, so the formula is CuSO₄.

Can I use the same molar mass for copper sulfate if it is hydrated differently?

No. The molar mass changes with the number of water molecules. For example, the trihydrate (CuSO₄·3H₂O) has a molar mass of 213.65 g/mol. Always use the exact formula of the compound you have.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 159.61 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →