molecalculator

Moles & Molar Mass

Mixed Air Formula for Indoor Air Quality

Calculator No. 01-8127 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The mixed air formula calculates the temperature (and optionally humidity) of air after two or more airstreams combine, which is essential for designing ventilation systems and predicting indoor air quality. You enter the flow rate and temperature of each airstream, and the calculator returns the resulting mixed air temperature. This value helps engineers size heating and cooling coils, evaluate economizer operation, and ensure occupant comfort.

Formula

The mixed air temperature (Tm) is the flow-weighted average of the individual airstream temperatures:

Tm = (T1·Q1 + T2·Q2) / (Q1 + Q2)

Where:

  • T1, T2 = dry-bulb temperatures of the two airstreams (°C)
  • Q1, Q2 = volumetric flow rates of the two airstreams (m³/s)

This is a simplified form of the energy balance assuming constant air density and specific heat, which is accurate for typical HVAC temperature ranges (0–50 °C) and low moisture levels.

Worked Example

Suppose 0.5 m³/s of return air at 22 °C mixes with 0.2 m³/s of outdoor air at 35 °C. Using the formula:

Tm = (22 × 0.5 + 35 × 0.2) / (0.5 + 0.2) = (11 + 7) / 0.7 = 18 / 0.7 = 25.71 °C

The mixed air temperature is 25.71 °C, which matches the calculator result.

Assumptions

  • Air density and specific heat are constant (valid for typical HVAC temperatures).
  • No heat loss or gain in the mixing plenum.
  • Steady-state conditions.
  • Volumetric flow rates are measured at the same conditions.

Why Mixed Air Matters for Indoor Air Quality

Mixed air is the result of combining outdoor ventilation air with recirculated indoor air before conditioning. The temperature of this blend directly affects the load on heating and cooling coils, but it also influences humidity and contaminant dilution. If outdoor air is too hot or too cold, the mixed air temperature may force the HVAC system to work harder, potentially reducing ventilation rates if the system is not properly designed. A well-designed mixing process ensures that the supply air is within the comfort zone (typically 20–26 °C) and that adequate outdoor air is delivered to dilute pollutants like CO₂, VOCs, and airborne particles.

How to Choose the Right Mixed Air Formula

For most HVAC design, the simple temperature-weighted formula above is sufficient. However, if you need to account for humidity (e.g., in humid climates or for psychrometric analysis), you must use enthalpy-weighted mixing:

hm = (h1·Q1 + h2·Q2) / (Q1 + Q2)

where h is specific enthalpy (kJ/kg). This is more accurate because it accounts for latent heat. For most quick estimates, the temperature formula is adequate, but for final designs, use a psychrometric chart or software.

Common Mistakes and Misconceptions

  • Using arithmetic average: If the flow rates are unequal, a simple average (e.g., (22+35)/2 = 28.5 °C) is wrong. Always weight by flow.
  • Ignoring units: Flow rates must be in the same units (m³/s, L/s, CFM). The calculator uses m³/s, but you can convert CFM to m³/s by multiplying by 0.000471947.
  • Assuming constant density: At high temperatures (>50 °C) or high altitudes, density changes matter, but for typical indoor conditions the error is under 1%.
  • Forgetting humidity: The temperature formula ignores moisture content. In humid climates, the mixed air enthalpy can be significantly different, affecting coil loads.

Costs and Energy Implications

Mixed air temperature directly affects energy consumption. If the mixed air is colder than the supply setpoint, the heating coil must add heat; if warmer, the cooling coil must remove it. Economizer systems use outdoor air for free cooling when the mixed air temperature is suitable. A poorly mixed airstream can cause short-cycling of equipment or uneven temperatures, increasing energy use by 10–20%. Proper mixing (using baffles or mixing plenums) ensures uniform temperature and reduces energy waste.

Safety and Practical Limits

When working with HVAC systems, always follow your facility’s safety procedures and the equipment manufacturer’s guidelines. The mixed air formula assumes no heat loss, but in reality, ductwork may gain or lose heat. Also, the formula does not account for pressure drops or fan heat gain. For critical applications, verify with actual measurements using calibrated sensors. Never use this formula for medical or clinical air quality decisions; consult a qualified engineer.

Frequently Asked Questions

What is the mixed air formula for three airstreams?

Extend the formula to Tm = (T₁Q₁ + T₂Q₂ + T₃Q₃) / (Q₁ + Q₂ + Q₃). The calculator above handles two streams, but the principle is the same: sum of (temperature × flow) divided by total flow.

Does mixed air temperature affect CO₂ levels?

Not directly. CO₂ concentration depends on the ratio of outdoor air to recirculated air, not the temperature. However, if the mixed air temperature is uncomfortable, occupants may reduce ventilation, which can increase CO₂. Proper ventilation design ensures both temperature and CO₂ are controlled.

Can I use this formula for humidity?

For humidity ratio (moisture content), you can use the same weighted average with humidity ratios (g/kg) instead of temperatures. For relative humidity, you must first convert to humidity ratio using psychrometric equations, then average, then convert back. The calculator here only handles temperature.

What if the flow rates are in CFM?

Convert CFM to m³/s by multiplying by 0.000471947. For example, 1000 CFM = 0.4719 m³/s. Then apply the formula. Alternatively, you can use any consistent unit for both flows, as long as they are the same.

Why is my mixed air temperature different from the calculated value?

Possible reasons: heat gain or loss in the mixing plenum, stratification (incomplete mixing), sensor inaccuracies, or neglecting fan heat. In practice, allow a margin of ±1–2 °C. For precise work, measure the actual mixed air temperature with a grid of sensors.

Related

Formula used
in t1 | Temperature of airstream 1 | °C | 22 | -40 | 60
in q1 | Flow rate of airstream 1 | m³/s | 0.5 | 0 | 100
in t2 | Temperature of airstream 2 | °C | 35 | -40 | 60
in q2 | Flow rate of airstream 2 | m³/s | 0.2 | 0 | 100
out tm | Mixed air temperature | °C | (t1*q1 + t2*q2) / (q1 + q2) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →