This molarity dilution calculator works out the final concentration after you dilute a solution by adding solvent. Enter the starting molarity and the starting and final volumes; it returns the diluted molarity and the dilution factor.
Formula
The dilution relationship is C₁V₁ = C₂V₂, so the final concentration is C₂ = C₁ × V₁ / V₂. Here, C₁ is the starting molarity in mol/L, V₁ is the volume of starting solution used in mL, C₂ is the final molarity in mol/L, and V₂ is the final total solution volume in mL. Because V₁ and V₂ use the same unit, their units cancel in the ratio; no mL-to-L conversion is needed for this calculation. The dilution factor is V₂ / V₁. The calculator requires a positive starting volume and a final volume at least as large as the starting volume; otherwise dilution is not possible under this model.
Worked Example
Using the defaults, C₁ = 1 mol/L, V₁ = 10 mL, and V₂ = 100 mL:
- Apply C₂ = C₁ × V₁ / V₂.
- C₂ = 1 mol/L × 10 mL / 100 mL = 0.1 mol/L.
- To four decimal places, the calculator displays 0.1000 mol/L.
- Dilution factor = 100 mL / 10 mL = 10.0000, a tenfold dilution.
Assumptions
- The solute amount stays constant: dilution adds solvent but does not add or remove solute.
- V₂ means the final total solution volume, not the volume of solvent added.
- Volumes are measured consistently and are additive for the practical calculation; the formula does not account for contraction or expansion on mixing.
- The starting concentration is known and refers to the same solute being diluted.
When to Use a Molarity Dilution Calculator
Use this calculation when you know a stock solution’s concentration and want to determine the concentration after taking a portion of it to a larger final volume. Molarity expresses the amount of solute in moles per litre of solution. Dilution changes the concentration because the same amount of solute occupies a larger volume; it does not, by itself, change the number of moles present.
For example, a tenfold dilution has a final volume ten times the stock aliquot. A 1 mol/L stock diluted from a 10 mL aliquot to a final volume of 100 mL becomes 0.1 mol/L. A twofold dilution means the final volume is twice the aliquot volume, so the final concentration is half the starting concentration. These descriptions concern the ratio of final volume to aliquot volume, not the amount of solvent poured in.
This is general chemistry and lab-planning arithmetic, not a clinical or medication calculation. It must not be used for medication, clinical, veterinary, injection, infusion, or other preparations for people or animals. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.
How to Read the Inputs and Results
- Starting molarity: Enter the stock solution concentration in mol/L. If the stock is stated in another unit, convert it first; for example, 1 mmol/L is 0.001 mol/L.
- Starting solution volume: Enter the volume of stock solution transferred into the diluted solution.
- Final solution volume: Enter the total volume after dilution. This is not the solvent volume alone.
- Final molarity: The concentration calculated from the starting concentration and the volume ratio.
- Dilution factor: Final volume divided by starting volume. A factor of 10 means the final concentration is one-tenth of the initial concentration.
For a requested final volume, the same relationship can be rearranged to find the aliquot: V₁ = C₂V₂/C₁. For a requested final concentration with a known aliquot, use V₂ = C₁V₁/C₂. These rearrangements are useful planning checks, but they do not change what the calculator’s displayed fields mean.
Common Errors and Practical Limits
The most common mistake is treating the solvent volume as V₂. If you transfer 10 mL of stock and add 90 mL of solvent, the intended final volume is approximately 100 mL only when the mixture’s volumes behave additively. In careful preparation, the method generally specifies bringing the mixture to the final volume, rather than assuming that a measured amount of solvent produces exactly that total volume.
- Mixing units: C₁ and C₂ must use the same concentration unit, and V₁ and V₂ must use the same volume unit. The ratio cancels units only when the volume units match.
- Using a larger aliquot than final volume: A final volume smaller than the stock aliquot is concentration, not dilution. The calculator rejects that input relationship.
- Rounding too early: Keep the available precision through intermediate calculations and round the reported result at the end. A calculator’s displayed decimals do not imply that the stock concentration or volume measurements are equally precise.
- Assuming exact real-world concentration: The result is only as reliable as the stock concentration, volume measurements, mixing, and solution stability.
The equation assumes the solute is conserved and that the stated stock concentration applies to the solution being used. It does not correct for evaporation, chemical reaction, precipitation, adsorption, temperature-related volume changes, or uncertainty in measurements. It also does not calculate how much solvent to add by itself; when the target volume is known, the nominal solvent amount is final volume minus stock aliquot, subject to the preparation method and real solution behavior.
Frequently Asked Questions
What is the formula for diluting a molar solution?
Use C₁V₁ = C₂V₂. To find the final molarity, rearrange it to C₂ = C₁V₁/V₂, keeping the volume units consistent.
Does final volume mean solvent volume?
No. It is the total volume of the diluted solution. The solvent amount is not automatically equal to the final volume.
How do I calculate a 1:10 dilution?
In common lab usage, a tenfold dilution has a final volume ten times the stock aliquot, giving one-tenth the starting concentration. Check the protocol’s definition of a dilution ratio, since notation can vary.
Can I use mL in the dilution equation?
Yes, if both V₁ and V₂ are in mL. Their ratio is dimensionless. Do not combine mL for one volume with L for the other without converting.
Why is my measured concentration different from the calculated value?
The equation gives an ideal result from entered values. Stock concentration uncertainty, volume measurement, incomplete mixing, temperature effects, and changes to the solute can all contribute to a difference.
Related
Formula used
in c1 | Starting molarity | mol/L | 1 | 0 in v1 | Starting solution volume | mL | 10 | 0 in v2 | Final solution volume | mL | 100 | 0 out c2 | Final molarity | mol/L | c1 * v1 / v2 | 4 out df | Dilution factor | - | v2 / v1 | 4
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Cubic Meters per Hour to Liters per Second0.2778 L/s