molecalculator

Moles & Molar Mass

Potassium Oxide Melting Point: Key Facts

Calculator No. 01-12520 · Updated · Formula and assumptions shown below

Concentration of K+ (from full dissociation) 0.4246 mol/L
Concentration in millimolar
424.65 mM
= Concentration of K+ (from full dissociation) × 1000
Mass of potassium in sample
8.301 g
Result, rounded to 3 decimal places
Mass of K2O sample
10 g
Set in the form below
You enter
Mass of K2O sample (g), Molar mass of K2O (g/mol), Volume of water (mL)
You get
Concentration of K+ (from full dissociation) (mol/L), Concentration in millimolar (mM), Mass of potassium in sample (g)
Rounding
4 dp · 2 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Potassium oxide (K2O) melts at approximately 740 °C (1364 °F). This value is a standard reference point, though the exact temperature can vary slightly depending on the measurement method and the purity of the sample.

Formula

The calculator above helps you convert a mass of potassium oxide into the concentration of potassium ions (K+) if the oxide were fully dissolved in water (in practice, K2O reacts vigorously with water to form KOH, so this is a theoretical calculation). The key formula is:

Concentration of K+ (mol/L) = (mass of K2O / molar mass of K2O) × 2 / (volume of water in L)

Where:

  • mass of K2O (g) – the amount of solid you start with.
  • molar mass of K2O (g/mol) – 94.196 g/mol (2 × 39.0983 + 15.999).
  • volume of water (mL) – the final volume of solution (converted to L by dividing by 1000).
  • The factor 2 appears because each formula unit of K2O contains two potassium atoms.

Worked Example

Using the default values from the calculator:

  • Mass of K2O = 10.0 g
  • Molar mass = 94.196 g/mol
  • Volume of water = 500 mL = 0.500 L

Step 1: Moles of K2O = 10.0 g / 94.196 g/mol = 0.10616 mol

Step 2: Moles of K+ = 0.10616 mol × 2 = 0.21232 mol

Step 3: Concentration = 0.21232 mol / 0.500 L = 0.42464 mol/L

Rounded to 4 decimal places: 0.4246 mol/L, which matches the calculator’s first output.

Assumptions

  • Complete dissociation of K2O into 2 K+ and O2− (theoretical; in water, O2− immediately reacts to form OH−).
  • Final volume equals the water volume (no volume change upon addition).
  • Temperature is 25 °C (density of water ≈ 1 g/mL).
  • Pure potassium oxide, no hydration or impurities.

What Is Potassium Oxide?

Potassium oxide is an ionic compound made of two potassium ions (K+) and one oxide ion (O2−). It is a pale yellow solid at room temperature. It is highly reactive with water, producing potassium hydroxide (KOH) with a strong exothermic reaction. Because of this, it is rarely found in pure form in nature; it appears mainly as a component of fertilizers and some glasses.

Why Does the Melting Point Matter?

The melting point of a substance is a fundamental physical property. For potassium oxide, knowing that it melts at ~740 °C helps in several contexts:

  • Industrial processes: In glassmaking and ceramics, potassium oxide is a flux that lowers the melting temperature of silica. Understanding its own melting point helps in designing furnace conditions.
  • Fertilizer production: Potassium oxide is often reported as “K2O equivalent” in fertilizer labels. The actual compound in fertilizer is usually potassium chloride or sulfate, but the melting point of the oxide is used in quality control.
  • Academic studies: In solid-state chemistry, melting point data help identify compounds and check purity.

How Is the Melting Point Measured?

Melting points of ionic compounds like K2O are typically measured using differential scanning calorimetry (DSC) or a hot-stage microscope. A small sample is heated at a controlled rate, and the temperature at which the solid transitions to liquid is recorded. Because K2O reacts with moisture and carbon dioxide in the air, measurements must be done under an inert atmosphere (like argon) to avoid contamination.

Common Problems and Misconceptions

One common mistake is confusing potassium oxide with potassium peroxide (K2O2) or potassium superoxide (KO2). These have different melting points and chemical properties. Another misconception is that K2O dissolves in water to give a simple solution of K+ and O2− ions; in reality, the oxide ion reacts instantly with water to form hydroxide ions (OH−). So the “concentration of K+” is what you get, but the solution is actually KOH.

Also, the melting point of K2O can be reported as a range (e.g., 740–760 °C) because of slight variations in measurement and purity. Always check the source of the data.

How to Choose Between K2O and Other Potassium Compounds

In practice, you rarely handle pure K2O because it is so reactive. For most applications, you choose among:

  • Potassium chloride (KCl) – common fertilizer, melting point 770 °C.
  • Potassium sulfate (K2SO4) – also a fertilizer, melting point 1069 °C.
  • Potassium hydroxide (KOH) – used in soaps and batteries, melting point 360 °C.

If you need a source of potassium for a reaction, KOH is often easier to handle than K2O. If you need a flux in glass, K2O is added in the form of potassium carbonate (K2CO3), which decomposes to K2O at high temperatures.

Safety and Handling

Potassium oxide is corrosive and reacts violently with water. If you work with it in a lab, always use gloves, safety goggles, and work in a fume hood. Keep it away from moisture and store it in a sealed container under an inert gas. The reaction with water generates heat and can cause splattering of caustic KOH solution. Follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

What is the exact melting point of potassium oxide?

Most references give 740 °C, but some report 760 °C. The difference is due to measurement conditions and purity. For practical purposes, 740 °C is the accepted value.

Is potassium oxide soluble in water?

It does not simply dissolve; it reacts with water to form potassium hydroxide (KOH). The reaction is vigorous and exothermic. So while it “disappears”, the oxide ion is converted to hydroxide.

Why is potassium oxide used in fertilizer labels?

Fertilizer labels show the percentage of “K2O equivalent” as a way to standardize the potassium content, even though the actual compound is usually KCl. It’s a convention, not a statement that K2O is present.

Does potassium oxide have a higher melting point than sodium oxide?

No. Sodium oxide (Na2O) melts at 1132 °C, which is higher than potassium oxide’s 740 °C. This is because the potassium ion is larger, leading to a weaker electrostatic attraction in the crystal lattice.

Can I melt potassium oxide in a regular furnace?

Yes, a standard laboratory furnace can reach 740 °C. However, you must use a crucible that can withstand the temperature and the corrosive nature of the oxide, such as platinum or alumina. Also, the furnace must be able to maintain an inert atmosphere to prevent reaction with air.

Related

Formula used
in m | Mass of K2O sample | g | 10.0 | 0
in mm | Molar mass of K2O | g/mol | 94.196 | 0.001
in v | Volume of water | mL | 500 | 0.001
out c | Concentration of K+ (from full dissociation) | mol/L | (m / mm) * 2 / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2
out massk | Mass of potassium in sample | g | m * (2 * 39.0983 / mm) | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →