molecalculator

Moles & Molar Mass

Radioactive Decay Differential Equation Calculator

Calculator No. 01-5281 · Updated · Formula and assumptions shown below

Nuclei remaining 500,000 nuclei
Fraction remaining
0.500000
Result, rounded to 6 decimal places
Initial number of radioactive nuclei
1000000 nuclei
Set in the form below
Elapsed time
3600 s
Set in the form below
You enter
Initial number of radioactive nuclei (nuclei), Elapsed time (s), Half-life (s)
You get
Nuclei remaining (nuclei), Fraction remaining
Rounding
0 dp · 6 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator applies the radioactive-decay differential equation to find how many radioactive nuclei remain after a chosen time. Enter the initial number of nuclei, the elapsed time, and the nuclide’s half-life; it returns the remaining number and the fraction left.

Formula

The decay law comes from the differential equation dN/dt = −λN. Its solution is N(t) = N0e−λt = N0 × 2−t/T1/2. Here, N(t) is the expected number of radioactive nuclei remaining, in nuclei; N0 is the initial number, in nuclei; t is elapsed time in seconds; λ is the decay constant in s−1; and T1/2 is half-life in seconds. The relationship is λ = ln(2)/T1/2.

The calculator uses the half-life form directly: N(t) = N0 × exp[−ln(2) × t/T1/2]. Both time inputs must use the same unit; here both are seconds. The factor ln(2) is dimensionless, so the exponent is dimensionless as required. If your time is in minutes, hours, or years, convert elapsed time and half-life to one common unit before calculation.

Worked Example

Use the defaults: N0 = 1,000,000 nuclei, t = 3,600 s, and T1/2 = 3,600 s.

  1. Calculate the time ratio: t/T1/2 = 3,600 s / 3,600 s = 1.
  2. Calculate the remaining fraction: exp[−ln(2) × 1] = 0.500000.
  3. Multiply by the initial count: N(t) = 1,000,000 × 0.500000 = 500,000 nuclei.

The outputs are 500,000 nuclei remaining and a fraction remaining of 0.500000. One half-life has passed, so half the original nuclei are expected to remain.

Assumptions

  • The sample contains one radionuclide with a constant half-life.
  • Decay events are independent, and the equation describes the expected population, not the exact outcome of individual random events.
  • Elapsed time and half-life are entered in the same units; the calculator labels both in seconds.
  • The model tracks the parent radionuclide only, not radioactive daughter products or changes in chemical form.

How the Decay Equation Works

Radioactive decay is a statistical process. For a large collection of identical radioactive nuclei, the probability of any one nucleus decaying during a short interval is proportional to the duration of that interval. The more undecayed nuclei present, the more decays are expected in that interval. This gives the rate equation dN/dt = −λN: the negative sign means the parent population decreases, and the proportionality constant λ sets the rate.

Separating variables and integrating gives ln[N(t)/N0] = −λt, which becomes N(t) = N0e−λt. A half-life is the time for the expected population to fall to half its starting value. Substituting N(T1/2) = N0/2 gives λ = ln(2)/T1/2, or equivalently the half-life form used above.

Reading the Result and Choosing Units

The fraction remaining is often easier to interpret than the count. A result of 0.25 means 25% of the initial parent nuclei are expected to remain; the fraction decayed is 1 − f. After one, two, or three half-lives, the expected fractions remaining are respectively 1/2, 1/4, and 1/8. More generally, after k half-lives the fraction is 2−k.

To use measured half-life data, convert both time values consistently. For example, if a nuclide’s half-life is given in years and elapsed time is also in years, their ratio can be calculated directly, even though this calculator’s input labels use seconds. For a manual calculation, use the same unit for each; do not put years in one place and seconds in the other. Half-lives vary enormously among nuclides, so use a reliable reference for the specific isotope rather than a value for the element in general.

Counts, Activity, and Common Misconceptions

The equation predicts a population, not an activity reading directly. Activity is the rate of nuclear transformations and is related to the number of parent nuclei by A = λN; activity is measured in becquerels, where 1 Bq equals one decay per second. If λ is in s−1 and N is a number of nuclei, the resulting activity is in Bq. The activity decreases with the same exponential time dependence when the decay constant remains fixed.

A common misconception is that exactly half the atoms in every small sample must decay during one half-life. The half-life describes a probability distribution and an expected fraction. In a sample with few nuclei, actual counts can differ noticeably from the expected value. Also, a radioactive atom does not gradually become less radioactive as it waits: an individual nucleus has a constant probability of decaying per unit time, while the population as a whole declines exponentially.

The displayed nucleus count is rounded to a whole number because physical nuclei are discrete. The underlying expectation can be fractional; that does not mean a fraction of a nucleus was observed. For very small populations, stochastic variation matters, and a continuous differential equation cannot predict the precise decay times of individual nuclei.

Limits and Related Decay Models

This simple equation applies to a single parent radionuclide whose decay constant does not change with time. It does not, by itself, describe a chain in which radioactive daughter nuclides also decay. For a parent and daughter, their populations are coupled: daughter production depends on parent decay, while daughter loss depends on the daughter’s own decay constant. Such cases require coupled differential equations and appropriate initial conditions.

For ordinary radioactive decay, the half-life is a nuclear property and is not meaningfully altered by routine changes in temperature, pressure, or chemical bonding. The model also assumes that the quantity entered as the initial number refers to the radioactive isotope, not all atoms of the element. If only isotope abundance or sample mass is known, an additional calculation using isotopic composition and molar mass is needed to find the number of radioactive nuclei. The calculator does not estimate radiation dose, shielding, biological effects, or safe handling conditions.

Frequently Asked Questions

What is the differential equation for radioactive decay?
The standard equation is dN/dt = −λN, where N is the number of undecayed parent nuclei and λ is the decay constant. Its solution is N(t) = N0e−λt.

How do I calculate the decay constant from half-life?
Use λ = ln(2)/T1/2. The half-life and the resulting decay constant must use compatible units. For example, a half-life in seconds gives λ in s−1.

How much of a radioactive sample remains after three half-lives?
The expected fraction is (1/2)3 = 1/8, or 12.5% of the original parent nuclei. The amount decayed is therefore expected to be 87.5%.

Does radioactive decay follow a linear equation?
No. The remaining population falls exponentially because the decay rate is proportional to how many nuclei remain. It may look nearly linear over a very short interval, but the general decay curve is not a straight line.

Is the number of nuclei remaining exact?
It is an expected value from a statistical model. Individual nuclei decay randomly, so actual counts—especially in a small sample—can differ from the calculated expectation.

Related

Formula used
in n0 | Initial number of radioactive nuclei | nuclei | 1000000 | 0
in t | Elapsed time | s | 3600 | 0
in h | Half-life | s | 3600 | 0
out n | Nuclei remaining | nuclei | n0 * exp(-ln(2) * t / h) | 0
out f | Fraction remaining | - | exp(-ln(2) * t / h) | 6

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →