molecalculator

Moles & Molar Mass

Sodium Nitrate Melting Point: 308 °C

Calculator No. 01-12523 · Updated · Formula and assumptions shown below

Volume of molten salt 45.21 mL
Amount of substance
1.000 mol
= Mass of sodium nitrate ÷ Molar mass of NaNO₃
Mass of sodium nitrate
85 g
Set in the form below
Molar mass of NaNO₃
84.995 g/mol
Set in the form below
You enter
Mass of sodium nitrate (g), Molar mass of NaNO₃ (g/mol), Density of molten NaNO₃ at 320 °C (g/mL)
You get
Volume of molten salt (mL), Amount of substance (mol)
Rounding
2 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Sodium nitrate (NaNO₃) melts at 308 °C (586 °F). This is the temperature at which the solid ionic compound transitions to a liquid at standard atmospheric pressure. The melting point is a key physical constant used in thermal storage systems, glass manufacturing, and metallurgy, and it is well established in standard reference tables.

Formula

The calculator above computes two basic quantities for a given mass of sodium nitrate: the volume it occupies when molten (using the density of the liquid near its melting point) and the number of moles. The formulas are:

  • Volume (mL) = mass (g) ÷ density (g/mL)
  • Amount (mol) = mass (g) ÷ molar mass (g/mol)

Where the molar mass of NaNO₃ is 22.990 (Na) + 14.007 (N) + 3 × 15.999 (O) = 84.995 g/mol. The density of molten sodium nitrate at about 320 °C is approximately 1.88 g/mL (it decreases slightly with increasing temperature). These values are used in engineering calculations for molten salt systems.

Worked Example

Using the default inputs: 85.0 g of sodium nitrate, molar mass 84.995 g/mol, and density 1.88 g/mL.

  1. Volume = 85.0 g ÷ 1.88 g/mL = 45.2 mL (rounded to 2 decimals: 45.21 mL).
  2. Amount = 85.0 g ÷ 84.995 g/mol = 1.000 mol (rounded to 3 decimals: 1.000).

So 85.0 g of sodium nitrate occupies about 45.2 mL as a liquid near its melting point, which is roughly 1 mole of the compound.

Assumptions

  • The density value is for pure molten NaNO₃ at ~320 °C; actual density varies with temperature and impurities.
  • The molar mass uses standard atomic weights (IUPAC abridged).
  • The melting point of 308 °C is for the pure compound at 1 atm; impurities lower the melting point.

Background: What Is Sodium Nitrate?

Sodium nitrate is an ionic compound composed of sodium cations (Na⁺) and nitrate anions (NO₃⁻). It is a white crystalline solid at room temperature, highly soluble in water (about 92 g per 100 mL at 25 °C). It occurs naturally as the mineral nitratine (Chile saltpeter) and is also produced industrially by neutralizing nitric acid with sodium carbonate or sodium hydroxide. Historically, it was a major nitrogen fertilizer, though it has largely been replaced by ammonium-based fertilizers. Today, it is used in food preservation (cured meats), glass and ceramics, explosives, and as a thermal energy storage medium.

Why Melting Point Matters

The melting point is a critical property for applications that involve heating sodium nitrate to its liquid state. For example, in concentrated solar power (CSP) plants, a mixture of sodium nitrate and potassium nitrate (60:40 by weight, called “solar salt”) is used as a heat transfer and storage fluid. The mixture melts at about 220 °C, which is lower than pure sodium nitrate, allowing the system to operate at lower temperatures to prevent freezing. In glass manufacturing, sodium nitrate is added to molten glass to remove bubbles and clarify the glass; knowing its melting point helps engineers control furnace temperatures. In metallurgy, it is used in heat-treating baths. The melting point also tells chemists about the strength of the ionic lattice: the higher the melting point, the stronger the electrostatic forces between ions.

How the Melting Point Is Measured

Melting points are typically measured using a capillary tube method or differential scanning calorimetry (DSC). In the capillary method, a small amount of powdered sample is packed into a thin glass tube and heated slowly in a heating block. The temperature at which the solid first begins to liquefy (the “onset”) and the temperature at which the last crystal disappears (the “clear point”) are recorded. For sodium nitrate, the reported value of 308 °C is the clear point. DSC measures the heat flow into the sample as it is heated; the endothermic peak corresponds to the melting transition. Both methods require careful calibration and a slow heating rate (1–2 °C/min) to obtain accurate values. Impurities lower the melting point and broaden the range, so a sharp melting point at 308 °C indicates a pure sample.

Common Misconceptions and Related Questions

Does sodium nitrate decompose when heated? Yes, but not at its melting point. Sodium nitrate is thermally stable up to about 380 °C. Above that, it begins to decompose to sodium nitrite (NaNO₂) and oxygen gas. At higher temperatures (above 500 °C), further decomposition can produce sodium oxide and nitrogen oxides. Therefore, when using molten sodium nitrate, you should avoid exceeding ~380 °C to prevent decomposition.

Is the melting point affected by pressure? For solids, pressure has a relatively small effect on melting point unless the pressure is extreme. For sodium nitrate, the melting point increases slightly with pressure, but the change is negligible for most practical applications. At standard atmospheric pressure, 308 °C is the accepted value.

Why is sodium nitrate sometimes called “Chile saltpeter”? Because large natural deposits of sodium nitrate were found in the Atacama Desert in Chile. The mineral form is called nitratine. This was a major source of nitrogen for fertilizers and explosives in the 19th and early 20th centuries.

Safety and Handling

Sodium nitrate is an oxidizing agent, meaning it can intensify the combustion of other materials. It is not flammable itself, but when heated to decomposition, it releases oxygen and toxic nitrogen oxides. Contact with strong reducing agents (e.g., aluminum powder, metal hydrides) can cause violent reactions. When handling solid sodium nitrate, wear safety goggles and gloves to avoid eye and skin irritation. When working with molten sodium nitrate, use proper thermal protection—it is hot enough to cause severe burns. Always follow your lab method, the safety data sheet (SDS) and your supervisor. Store sodium nitrate in a cool, dry, well-ventilated area away from combustible materials and reducing agents.

Alternatives and Comparisons

Other nitrate salts have different melting points. Potassium nitrate (KNO₃) melts at 334 °C, which is higher than sodium nitrate. Calcium nitrate (Ca(NO₃)₂) melts at about 561 °C, but it often exists as a hydrate. Lithium nitrate (LiNO₃) melts at 255 °C, lower than sodium nitrate. For thermal storage, a mixture of sodium and potassium nitrates (60:40) is common because it melts at ~220 °C, lower than either pure salt, which reduces the risk of freezing in pipes. For food preservation, sodium nitrate is often used in combination with sodium nitrite, but the melting point is not a relevant factor in that application. If you need a lower melting point for a specific process, consider using a eutectic mixture or a different salt.

Frequently Asked Questions

What is the exact melting point of sodium nitrate? The accepted melting point is 308 °C (586 °F) at standard atmospheric pressure. Some sources report 306.8 °C, but 308 °C is the most commonly cited value.

Does sodium nitrate melt or decompose first? It melts first. The melting point (308 °C) is well below the decomposition temperature (about 380 °C), so you can safely melt it without significant decomposition if you do not overheat it.

Why does the melting point of sodium nitrate vary in different sources? Variations can arise from impurities, measurement methods, and heating rates. The presence of water or other salts can lower the melting point. High-purity samples give the sharpest and most accurate value.

Can I use sodium nitrate in a home furnace to melt it? It is not recommended. Heating sodium nitrate to 308 °C requires specialized equipment and safety precautions. The molten salt is corrosive and can cause severe burns. Also, overheating can release toxic gases. This is a lab or industrial operation, not a home project.

What is the melting point of a 60/40 sodium nitrate/potassium nitrate mixture? The eutectic mixture (60% NaNO₃, 40% KNO₃ by weight) melts at about 222 °C. This is significantly lower than either pure component, which is why it is used in solar thermal plants.

Related

Formula used
in m | Mass of sodium nitrate | g | 85.0 | 0
in mm | Molar mass of NaNO₃ | g/mol | 84.995 | 0.001
in d | Density of molten NaNO₃ at 320 °C | g/mL | 1.88 | 0
out v | Volume of molten salt | mL | m / d | 2
out n | Amount of substance | mol | m / mm | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →