The specific gas constant of hydrogen gas is approximately 4,124 J/(kg·K), or 4.124 kJ/(kg·K). This calculator determines it from hydrogen’s molar mass; enter the molar mass in g/mol to get the specific gas constant in J/(kg·K), with a supporting value in kJ/(kg·K).
Formula
The specific gas constant is the universal molar gas constant divided by the gas’s molar mass:
Rs = Ru / M
- Rs is the specific gas constant, in J/(kg·K).
- Ru is the universal molar gas constant, 8.31446261815324 J/(mol·K).
- M is molar mass in kg/mol. The calculator accepts M in g/mol, so it converts by dividing by 1,000: Rs = 8.31446261815324 × 1,000 / M, where M is entered in g/mol.
For molecular hydrogen, H2, the default molar mass is 2.016 g/mol, based on the conventional atomic weight of hydrogen, 1.008 g/mol, multiplied by two atoms per molecule. This produces approximately 4,124 J/(kg·K), or 4.124 kJ/(kg·K).
Worked Example
Using the default molar mass of 2.016 g/mol:
Rs = 8.31446261815324 × 1,000 / 2.016
Rs ≈ 4,124 J/(kg·K), rounded to a whole number.
In kilojoules per kilogram-kelvin, divide by 1,000: 4,124.237 × 1,000−1 ≈ 4.124 kJ/(kg·K), rounded to three decimal places. Small differences in the last digits can result from the molar-mass convention or rounding.
Assumptions
- The gas is molecular hydrogen, H2, rather than atomic hydrogen.
- The molar mass is 2.016 g/mol, using an abridged conventional atomic weight of 1.008 g/mol for hydrogen.
- This calculation defines a gas constant from molar mass; it does not assume a particular temperature or pressure.
- The ideal-gas equation is the context in which this constant is commonly used. Real-gas behavior can depart from that model, especially at high pressure or low temperature.
What the Specific Gas Constant Means
The universal gas constant applies per mole, while the specific gas constant applies per unit mass. The distinction is useful whenever gas quantities are expressed in kilograms rather than moles. For an ideal gas, the mass-based equation is p = ρRsT, where p is absolute pressure in pascals, ρ is density in kg/m³, T is absolute temperature in kelvins, and Rs is in J/(kg·K).
It is called “specific” because it is tied to a particular gas through its molar mass. The universal value Ru is the same for all ideal gases, but Rs changes with the gas. A lighter gas has a larger specific gas constant: dividing the same universal constant by a smaller molar mass gives a larger result.
Hydrogen Gas and Its Molar Mass
Hydrogen gas under ordinary chemical conditions is diatomic: its molecules contain two hydrogen atoms and are written H2. Using 1.008 g/mol per hydrogen atom gives a molecular molar mass of 2.016 g/mol. The calculator uses this value as its default. For a different isotopic composition, or a different gas altogether, replace the molar-mass input with the relevant value.
Do not confuse hydrogen gas, H2, with atomic hydrogen, H. A single hydrogen atom has about half the molar mass of an H2 molecule, so its mass-specific gas constant would be about twice as large. That is a different species and is not the ordinary hydrogen-gas value asked for here.
Using the Value in Gas Calculations
In the ideal-gas model, hydrogen’s specific gas constant lets you relate pressure, density and absolute temperature directly. For example, the density equation rearranges to ρ = p/(RsT). Use pressure in pascals and temperature in kelvins if using Rs in J/(kg·K); mixing units changes the numerical result.
- Convert Celsius temperature to kelvins by adding 273.15. Gas-law temperature must be absolute.
- Use absolute pressure, not gauge pressure. Convert a gauge reading by accounting for atmospheric pressure where appropriate.
- Check whether the equation expects mass density in kg/m³ or a molar quantity in mol/m³.
- Keep the constant’s units attached to the value. The numerical value in J/(kg·K) is 1,000 times the value in kJ/(kg·K).
For instance, using the result as 4.124 rather than 4,124 is correct only if the equation’s energy units and other terms are consistent with kJ rather than J. A bare number without its units is not enough to safely identify which convention is being used.
Common Confusions and Model Limits
The most common confusion is between the universal gas constant and the specific gas constant. The universal constant, 8.31446261815324 J/(mol·K), is per mole. The hydrogen-specific value, about 4,124 J/(kg·K), is per kilogram. They describe the same gas-law framework but cannot be substituted for one another without converting between mole and mass amounts.
Another frequent mistake is using a molar mass in kg/mol in a formula that expects g/mol, or vice versa. The calculator explicitly multiplies by 1,000 because its input is in g/mol. If you calculate manually with M = 0.002016 kg/mol, use Rs = 8.31446261815324 / 0.002016 instead; do not apply the gram-to-kilogram factor a second time.
The constant itself is derived from molar mass and the universal gas constant, but using it in an equation of state does not make every gas sample ideal. At sufficiently high pressure or near condensation conditions, real hydrogen’s pressure-volume-temperature behavior can differ from the ideal-gas prediction. More accurate engineering calculations may require a real-gas equation of state or measured property data for the conditions of interest.
Frequently Asked Questions
What is the specific gas constant of hydrogen in SI units?
The commonly used value for molecular hydrogen is about 4,124 J/(kg·K), equivalent to 4.124 kJ/(kg·K), based on a molar mass of 2.016 g/mol.
Why is hydrogen’s specific gas constant so large?
The specific value is the universal molar gas constant divided by molar mass. Hydrogen molecules are very light, so the result per kilogram is relatively large.
Is hydrogen’s specific gas constant the same as the universal gas constant?
No. The universal gas constant is 8.31446261815324 J/(mol·K), while hydrogen’s specific gas constant is about 4,124 J/(kg·K). Their denominators—and therefore their units—differ.
Should I use the value for H or H2?
Use H2 for ordinary hydrogen gas. H denotes an individual hydrogen atom, not the usual diatomic gas molecule, and leads to a different mass-specific value.
Does the value change with temperature or pressure?
The specific gas constant calculated from a fixed molar mass does not change with temperature or pressure. However, the accuracy of ideal-gas calculations using it can vary with conditions because real hydrogen is not perfectly ideal.
Related
Formula used
in mm | Molar mass of hydrogen gas | g/mol | 2.016 | 0.001 out r | Specific gas constant | J/(kg·K) | 8.31446261815324 * 1000 / mm | 0 out rk | Specific gas constant | kJ/(kg·K) | r / 1000 | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Cubic Meters per Hour to Liters per Second0.2778 L/s