Rediluting an acid means adding solvent to an existing acid solution to lower its concentration; the final value depends on the starting concentration and the volumes involved. This calculator works out the new molarity when you enter the initial concentration, the volume of acid solution used, and the final total solution volume.
Formula
The calculation uses conservation of solute: the amount of acid present before dilution is the same amount present after adding solvent, assuming no acid is lost or consumed.
C1V1 = C2V2, so C2 = C1 × V1 / V2.
- C1 is the initial acid concentration in mol/L.
- V1 is the volume of the initial acid solution used, in mL.
- C2 is the final concentration in mol/L.
- V2 is the final total solution volume, in mL.
Because both volumes are entered in the same unit, their ratio is dimensionless and the volume units cancel. The millimolar output converts mol/L to mmol/L by multiplying by 1,000. The equation is often written C1V1 = C2V2; “redilute” does not require a different formula from an ordinary dilution.
Worked Example
Using the calculator’s default values:
- Initial concentration, C1 = 1 mol/L
- Initial acid-solution volume, V1 = 10 mL
- Final solution volume, V2 = 100 mL
First, calculate the amount represented by concentration times volume: 1 mol/L × 10 mL = 10 mol·mL/L. Divide by the final volume to find the new concentration:
C2 = (1 mol/L × 10 mL) / 100 mL = 0.1 mol/L.
Convert to millimolar: 0.1 mol/L × 1,000 = 100 mmol/L. The calculator therefore returns 0.1000 mol/L and 100.00 mmol/L.
Assumptions
- The acid is mixed uniformly, and the amount of acid remains unchanged during dilution.
- The entered final volume is the total solution volume, not the amount of solvent added.
- The calculation reports formal concentration; it does not calculate pH, acid activity, heat release, or reaction products.
- For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.
What “Redilute” Means
To dilute is to reduce concentration by increasing the solution’s volume without changing the amount of dissolved acid. “Redilute” commonly refers to diluting a solution that was already made by dilution, or simply diluting it again. Each stage can be calculated from the concentration immediately before that stage, or the whole sequence can be represented by the original amount of acid and the final total volume.
For successive dilutions, the concentration changes multiply. For example, a tenfold dilution followed by another tenfold dilution gives an overall hundredfold dilution: the final concentration is one-hundredth of the starting concentration. Keep track of the concentration and total volume at every step; rounding intermediate values can introduce avoidable error.
How to Use and Interpret the Result
Enter the concentration of the solution you actually have, the volume of that solution being used, and the intended final volume. Do not enter the quantity of water or other solvent alone as the final volume. If 10 mL of solution is brought to a total of 100 mL, then V2 is 100 mL. The amount of solvent added is approximately 90 mL only when volumes are treated as additive; that is not the value used in the dilution equation.
The result should be lower than the initial concentration whenever the final volume exceeds the starting-solution volume. If the final volume equals the initial volume, the concentration remains the same. If the stated final volume is smaller, the equation describes concentrating rather than diluting. Check that the final volume is at least as large as the solution volume used; this calculator does not enforce that relationship.
As a separate example, a 0.5 mol/L solution diluted from 20 mL to 200 mL becomes 0.05 mol/L: 0.5 × 20 / 200 = 0.05. The acid amount represented by C×V is unchanged, while concentration falls in proportion to the increase in total volume.
Common Errors and Limits
- Confusing solvent volume with final volume: “add 100 mL of water” is not the same as “dilute to 100 mL.” Use the final total volume for V2.
- Mixing units: If one volume is in liters and the other in milliliters, convert one so both match before applying the equation. The calculator’s volume fields are both in mL.
- Using an uncertain starting concentration: The answer cannot be more reliable than the concentration and volume measurements entered.
- Treating molarity as pH: Molarity measures the formal amount of acid per solution volume. It does not by itself determine pH, especially for weak acids or concentrated solutions.
The simple equation assumes the acid is neither neutralized nor lost and that the final solution is mixed evenly. It does not account for chemical reactions, changes in volume on mixing, density, temperature-dependent volume changes, or non-ideal behavior. For high-accuracy work, use the concentration convention and preparation method specified by the relevant analytical procedure. This is a calculation aid, not a substitute for a validated method or appropriate laboratory controls.
Safety When Diluting Acid
Acid dilution can release heat, and splashes can cause serious injury. The calculator only predicts concentration; it does not determine whether a particular operation is safe or specify a preparation procedure. Consult the acid’s safety data sheet and your institution’s approved method, and use the required protective equipment and engineering controls. Never use a calculator result as a substitute for hazard assessment or supervision.
Frequently Asked Questions
What is the formula for rediluting acid?
Use C1V1 = C2V2. Rearranged, the final concentration is C2 = C1V1/V2, with consistent volume units.
Does rediluting acid change the amount of acid?
In an ideal dilution, no. It changes the solution volume and concentration, while the amount of acid remains constant.
Should I use the water volume or final volume?
Use the final total solution volume. The solvent volume alone is not V2.
Can I calculate pH from the rediluted concentration?
Not in general. pH depends on acid strength and solution conditions as well as concentration; weak acids and concentrated solutions need additional treatment.
What if I dilute the acid twice?
Apply the dilution equation at each stage, using each stage’s starting concentration and final volume, or multiply the dilution factors to find the overall change. Avoid rounding intermediate concentrations unnecessarily.
Related
Formula used
in c1 | Initial acid concentration | mol/L | 1 | 0 in v1 | Initial acid-solution volume | mL | 10 | 0 in vf | Final solution volume | mL | 100 | 0 out c2 | Rediluted acid concentration | mol/L | c1 * v1 / vf | 4 out c2mm | Concentration in millimolar | mmol/L | c2 * 1000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Cubic Meters per Hour to Liters per Second0.2778 L/s