molecalculator

Moles & Molar Mass

Volume at Standard Pressure: Gas Law Calculator

Calculator No. 01-5777 · Updated · Formula and assumptions shown below

Gas volume 22.4140 L
Molar volume
22.4140 L/mol
= Gas volume ÷ Amount of gas
Amount of gas
1 mol
Set in the form below
Temperature
0 °C
Set in the form below
You enter
Amount of gas (mol), Temperature (°C), Absolute pressure (kPa)
You get
Gas volume (L), Molar volume (L/mol)
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Volume at standard pressure depends on the amount of gas, its temperature, and the pressure meant by “standard.” This calculator uses the ideal gas law: enter the gas amount in moles, temperature in °C, and pressure in kPa to calculate volume in liters. Its default conditions are 0 °C and 101.325 kPa, where one mole of an ideal gas occupies about 22.414 L.

Formula

The ideal gas law is PV = nRT. Solving for volume gives V = nRT/P. The calculator’s expression converts temperature from Celsius to kelvin by adding 273.15, converts pressure from kilopascals to atmospheres by dividing by 101.325, uses R = 0.0820574 L·atm/(mol·K), then converts the resulting volume from liters as needed. Equivalently, its first output expression uses R = 8.31446261815324 J/(mol·K) with pressure converted to pascals; the expression as supplied is intended to implement the ideal-gas calculation in liters.

  • V is gas volume in liters (L).
  • n is amount of gas in moles (mol).
  • T is absolute temperature in kelvin (K), calculated as °C + 273.15.
  • P is absolute pressure. The input is in kPa; 101.325 kPa equals 1 standard atmosphere.
  • R is the ideal gas constant. In compatible units, R = 0.0820574 L·atm/(mol·K), or 8.31446261815324 J/(mol·K).

“Standard pressure” is not a complete set of conditions by itself. It generally identifies pressure, while standard temperature and pressure (STP) conventions also specify a temperature. The default here uses 0 °C (273.15 K) and 101.325 kPa (1 atm), a common textbook convention. Since the output is proportional to temperature in kelvin and inversely proportional to pressure, changing either condition changes the calculated volume.

Worked Example

Using the defaults—n = 1 mol, t = 0 °C, and p = 101.325 kPa—first convert temperature: T = 0 + 273.15 = 273.15 K. Convert pressure: P = 101.325 / 101.325 = 1 atm. Then use the gas constant in L·atm/(mol·K):

V = (1 mol × 0.0820574 L·atm/(mol·K) × 273.15 K) / 1 atm = 22.41397 L, or 22.4140 L to four decimal places. The molar volume is V/n = 22.41397 L / 1 mol = 22.4140 L/mol.

Assumptions

  • The gas behaves ideally: particles have negligible volume and intermolecular attractions under the conditions considered.
  • Temperature is entered in °C and must be at or above absolute zero; the calculation converts it to kelvin.
  • Pressure is absolute pressure, not gauge pressure. The input must be greater than zero.
  • The standard-pressure reference is 101.325 kPa, equal to 1 atm. The default temperature is 0 °C.
  • The gas amount is in moles. The calculator does not determine moles from a mass or identify a gas’s composition.

What “Standard Pressure” Means

Standard pressure can refer to a reference value used to report or compare measurements; it does not automatically tell you the gas temperature. One atmosphere is 101.325 kPa. Another widely used standard-pressure reference is 1 bar, exactly 100 kPa. These pressures are close but not identical, so a precise calculation should state which one it uses.

STP is also used with more than one temperature convention. A common general-chemistry convention pairs 1 atm with 0 °C. Some scientific and technical references use 1 bar as standard pressure, and may specify a different standard temperature. Do not assume that a value labeled “STP” uses the same convention in every source; check the stated temperature and pressure before comparing volumes.

How to Use the Result

The output is the ideal-gas volume for the entered amount at the entered temperature and absolute pressure. At the default settings, one mole gives approximately 22.414 L. For two moles at unchanged temperature and pressure, the predicted volume doubles; for the same amount of gas at twice the absolute pressure, the predicted volume halves.

Use the calculator for classroom gas-law problems, approximate comparisons, and preliminary calculations where ideal behavior is reasonable. It can also help convert a measured or specified amount in moles into an estimated gas volume at a stated condition. To calculate moles from a gas volume instead, rearrange the same relationship to n = PV/(RT), keeping units consistent.

  • Use absolute pressure. If a pressure gauge reports pressure above local atmospheric pressure, add atmospheric pressure to obtain absolute pressure before entering it.
  • Use kelvin in the formula. The calculator handles the Celsius-to-kelvin conversion; do not enter a kelvin value in the Celsius field.
  • Keep pressure units consistent. Here, pressure is entered in kPa and compared with 101.325 kPa per atmosphere.
  • Report the conditions with the result. A volume without its temperature and pressure is incomplete for a gas because the volume changes when those conditions change.

Ideal Gas Limits and Common Misconceptions

The ideal gas law is an approximation, not a guarantee that every real gas occupies the calculated volume. It is often useful at relatively low pressure and sufficiently high temperature, where gas particles are comparatively far apart. Real gases can differ more at high pressures or near condensation, when particle size and intermolecular forces matter. For precise work under non-ideal conditions, use a suitable real-gas equation or reliable property data for the specific gas and conditions.

A frequent misconception is that “one mole always occupies 22.4 liters.” That value is not universal: it applies approximately to an ideal gas at 0 °C and 1 atm. At a different temperature or pressure, the molar volume changes. At 25 °C and 1 atm, for example, the ideal molar volume is about 24.47 L/mol, because the absolute temperature is higher.

Another distinction is between standard conditions and room conditions. A gas sample in a room is not necessarily at 0 °C, and a laboratory’s atmospheric pressure may differ from 1 atm. If conditions are measured, enter those values rather than assuming the defaults. The equation also presumes the entered amount is the gas-phase amount; it does not account for gas dissolved in a liquid or a mixture’s humidity unless those effects are handled separately.

Frequently Asked Questions

What is the volume of one mole of gas at standard pressure?
Pressure alone is not enough to specify the volume; temperature matters too. At 0 °C and 1 atm, one mole of an ideal gas occupies about 22.414 L. At 25 °C and the same pressure, it occupies about 24.47 L.

Is standard pressure 1 atm or 1 bar?
Both are used as reference pressures in different contexts. One atmosphere is 101.325 kPa, while one bar is exactly 100 kPa. State the convention used when precision matters.

Does standard pressure mean STP?
Not by itself. Standard pressure specifies a pressure reference; STP refers to a set of standard conditions and conventions may differ, particularly in the selected pressure or temperature.

Can I use gauge pressure in the calculator?
No. The input must be absolute pressure. Gauge pressure measures pressure above local atmospheric pressure, so add atmospheric pressure to a gauge reading before using it.

Why does the calculated gas volume differ from a measured value?
Possible causes include non-ideal gas behavior, different actual temperature or pressure, measurement uncertainty, or an incorrect STP convention. Check the conditions and whether an ideal-gas approximation is adequate for the gas and pressure range.

Related

Formula used
in n | Amount of gas | mol | 1 | 0
in t | Temperature | °C | 0 | -273.15
in p | Absolute pressure | kPa | 101.325 | 0.001
out v | Gas volume | L | n * 8.31446261815324 * (t + 273.15) / (p / 101.325) / 101.325 | 4
out vm | Molar volume | L/mol | v / n | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →