molecalculator

Moles & Molar Mass

Enthalpy of Moist Air: Formula & Calculator

Calculator No. 01-6859 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The enthalpy of moist air is the total heat content per unit mass of dry air, including the sensible heat of the air and water vapor plus the latent heat of any moisture present. This calculator computes the specific enthalpy (kJ/kg dry air) from dry-bulb temperature and humidity ratio (absolute humidity), using the standard psychrometric formula.

Formula

The specific enthalpy of moist air (h) is expressed per kilogram of dry air, not per kilogram of moist air. The standard formula used in psychrometrics is:

h = cp,air · t + W · (hfg0 + cp,vapor · t)

Where:

  • h = specific enthalpy of moist air, kJ/kg dry air
  • cp,air = specific heat of dry air at constant pressure ≈ 1.006 kJ/(kg·°C)
  • t = dry-bulb temperature, °C
  • W = humidity ratio (mass of water vapor per mass of dry air), kg/kg
  • hfg0 = latent heat of vaporization of water at 0 °C ≈ 2501 kJ/kg
  • cp,vapor = specific heat of water vapor ≈ 1.86 kJ/(kg·°C)

The equation assumes the reference state is 0 °C with zero enthalpy for both dry air and liquid water. It is valid for typical HVAC conditions (−40 °C to 60 °C dry-bulb) and is the same formula used to construct psychrometric charts.

Worked Example

Calculate the enthalpy of moist air at 25 °C dry-bulb temperature and a humidity ratio of 0.010 kg/kg (typical of comfortable indoor air).

  1. Sensible heat of dry air: 1.006 × 25 = 25.15 kJ/kg dry air
  2. Latent heat term: 2501 + 1.86 × 25 = 2501 + 46.5 = 2547.5 kJ/kg water vapor
  3. Multiply by humidity ratio: 0.010 × 2547.5 = 25.475 kJ/kg dry air
  4. Add the two parts: 25.15 + 25.475 = 50.625 kJ/kg dry air

Rounded to three decimals, the result is 50.625 kJ/kg dry air, which matches the calculator output.

Assumptions

  • Moist air behaves as an ideal gas mixture (valid at atmospheric pressure and typical HVAC temperatures).
  • Specific heats of dry air and water vapor are constant over the temperature range.
  • Reference state: 0 °C, enthalpy of dry air and liquid water set to zero.
  • No dissolved gases or contaminants in the water vapor.
  • Pressure is near 1 atm; the formula does not explicitly include pressure because enthalpy of an ideal gas is independent of pressure.

Why Moist Air Enthalpy Matters

Enthalpy is the key quantity in heating, ventilation, and air conditioning (HVAC) design. It tells you how much energy is needed to heat, cool, humidify, or dehumidify air. For example, when you cool air below its dew point, moisture condenses and releases latent heat; the enthalpy change accounts for both the temperature drop and the water removal. Engineers use enthalpy to size cooling coils, estimate cooling loads, and evaluate the performance of evaporative coolers. In drying processes (food, timber, textiles), the enthalpy of the air determines how much moisture it can absorb and how much heat must be supplied.

How to Use the Calculator

Enter the dry-bulb temperature in °C and the humidity ratio in kg of water vapor per kg of dry air. The humidity ratio is often measured directly with a hygrometer or calculated from relative humidity and pressure. If you only know relative humidity, use a psychrometric chart or a separate calculator to find W first. The result is the specific enthalpy per kilogram of dry air. To get the total enthalpy of a given air stream, multiply by the mass flow rate of dry air (not the total air flow). For example, if your system moves 2 kg/s of dry air at 25 °C and W = 0.010, the total enthalpy flow is 2 × 50.625 = 101.25 kJ/s (kW).

Common Misconceptions and Mistakes

  • Per kg of moist air vs. dry air: The standard psychrometric enthalpy is per kg of dry air. Using total moist air mass introduces errors, especially at high humidity.
  • Ignoring latent heat: At 25 °C and W = 0.010, the latent portion is about half the total enthalpy. Neglecting it underestimates cooling loads significantly.
  • Unit mix-ups: The formula uses kJ/kg and °C. If you have temperatures in °F or humidity in grains per pound, convert first (1 lb = 7000 grains; °C = (°F − 32) × 5/9).
  • Using 4.18 kJ/kg·°C for liquid water: That is for liquid water, not water vapor. The vapor specific heat is about 1.86 kJ/kg·°C.
  • Assuming enthalpy is zero at 0 °C: This is a reference choice, not a physical absolute. Always compare enthalpies relative to the same reference.

Limitations and Real-World Considerations

The formula is accurate for pressures near 1 atm and temperatures from about −40 °C to 60 °C. At very high pressures (e.g., compressed air systems), the ideal gas assumption breaks down and real-gas corrections are needed. At extremely low temperatures, the specific heat of ice and sublimation effects must be included. The formula also assumes that the air is fully saturated with water vapor up to the given W; if the air is supersaturated (fog), the excess water is liquid and contributes different enthalpy. For most HVAC and drying applications, the given formula is sufficient. For precise work, consult a psychrometric chart or a more detailed equation of state.

Frequently Asked Questions

What is the difference between enthalpy and temperature?

Temperature measures the average kinetic energy of molecules, while enthalpy measures the total energy content, including both sensible (temperature-related) and latent (phase-change) energy. Two air samples at the same temperature can have very different enthalpies if they have different moisture contents. For example, humid air at 30 °C has more enthalpy than dry air at 30 °C because it contains extra water vapor that carries latent heat.

How do I convert relative humidity to humidity ratio?

Humidity ratio W = 0.622 × (pv / (p − pv)), where pv is the partial pressure of water vapor and p is total pressure. pv = (RH/100) × psat(t), where psat(t) is the saturation vapor pressure at the dry-bulb temperature (use standard tables or the Antoine equation). For example, at 25 °C, psat ≈ 3.169 kPa, RH = 50%, pv = 1.5845 kPa, and at 101.325 kPa total pressure, W = 0.622 × (1.5845 / (101.325 − 1.5845)) ≈ 0.00986 kg/kg.

Why is enthalpy per kg of dry air, not per kg of air?

Because the mass of dry air remains constant during typical processes (heating, cooling, humidifying), while the moisture content changes. Using dry air as the basis makes energy balances simpler: you track the dry air flow and account for water added or removed separately. It is a convention adopted in psychrometrics and HVAC engineering.

Does altitude affect moist air enthalpy?

The formula itself does not include pressure, so for a given temperature and humidity ratio, enthalpy is essentially the same at any altitude. However, at higher altitudes the atmospheric pressure is lower, which affects the humidity ratio achievable for a given relative humidity. If you know W, the enthalpy formula remains valid. For design, you must use the correct W for your elevation.

Can I use this for air at very high temperatures, like in a dryer?

For temperatures up to about 60 °C, the constant specific heat assumption is fine. Above that, the specific heats of air and vapor increase with temperature, and the latent heat of vaporization changes. For industrial dryers operating at 100–200 °C, use a more precise formula or a psychrometric chart that accounts for temperature-dependent properties. This calculator is intended for HVAC and typical environmental conditions.

Why does the enthalpy increase with humidity even at the same temperature?

Because water vapor carries latent heat of vaporization. To evaporate water into the air, energy is absorbed (about 2501 kJ/kg at 0 °C). That energy remains in the vapor as latent heat. When you humidify air, you add both the sensible heat of the vapor and the latent heat, so the total enthalpy rises even if the dry-bulb temperature stays the same.

Related

Formula used
in t | Dry-bulb temperature | °C | 25 | -40 | 60
in w | Humidity ratio | kg water/kg dry air | 0.010 | 0 | 0.200
out h | Specific enthalpy of moist air | kJ/kg dry air | 1.006 * t + w * (2501 + 1.86 * t) | 3
out hSI | Enthalpy in SI (per kg dry air) | kJ/kg dry air | h | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →