molecalculator

Moles & Molar Mass

Finding Half Life from Decay Rate

Calculator No. 01-6978 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

To find the half-life of a radioactive substance from its decay rate (the activity, measured in becquerels or curies), you first convert the decay rate to the decay constant λ using λ = A / N, where A is the activity and N is the number of radioactive atoms, then plug λ into t₁/₂ = ln(2) / λ. If you know the activity and the initial number of atoms (or the mass and molar mass), this calculator does the conversion and gives you the half-life directly.

Formula

The decay of a radioactive isotope follows first-order kinetics. The activity A (decay rate) is proportional to the number of radioactive atoms N:

A = λ × N

  • A = activity (decays per second, Bq)
  • λ = decay constant (s⁻¹)
  • N = number of radioactive atoms present

Rearranging gives λ = A / N. The half-life t₁/₂ is the time for half the atoms to decay, related to λ by:

t₁/₂ = ln(2) / λ

Combining the two:

t₁/₂ = ln(2) × N / A

To get N from mass, use the molar mass M and Avogadro’s number NA = 6.02214076 × 10²³ mol⁻¹:

N = (m / M) × NA

In the calculator, the activity is entered in becquerels (Bq, decays per second), mass in grams, and molar mass in g/mol. The result is the half-life in seconds, then converted to years using 365.25 days per year.

Worked Example

Suppose you have a 1.000 g sample of pure radium-226 (molar mass 226.025 g/mol) and measure its activity as 1000 Bq. Find the half-life.

  1. Number of atoms: N = (1.000 g / 226.025 g/mol) × 6.02214076 × 10²³ = 2.6643 × 10²¹ atoms.
  2. Decay constant: λ = A / N = 1000 / (2.6643 × 10²¹) = 3.7534 × 10⁻¹⁹ s⁻¹.
  3. Half-life: t₁/₂ = ln(2) / λ = 0.693147 / (3.7534 × 10⁻¹⁹) = 1.8467 × 10¹⁸ s.
  4. Convert to years: t₁/₂ = 1.8467 × 10¹⁸ / (365.25 × 24 × 3600) = 5.852 × 10¹⁰ years.

The calculator gives the same result: 1.8467 × 10¹⁸ s, or 5.852 × 10¹⁰ years. (The actual half-life of Ra-226 is about 1.6 × 10³ years, so a 1000 Bq activity from 1 g would be far too low – this example is purely for arithmetic practice.)

Assumptions

  • The sample contains only one radioactive isotope (no daughter products contributing to activity).
  • The decay rate is measured at a single moment and is much larger than background radiation.
  • The molar mass is that of the pure isotope, not the natural element mixture.
  • No significant amount of the isotope has decayed during the measurement (activity is essentially constant over the measurement time).

How to Measure the Decay Rate

The decay rate (activity) is measured with a radiation detector – a Geiger-Müller counter, scintillation detector, or ion chamber. The detector counts ionizing events per second; after correcting for detector efficiency, geometry, and background, you get the activity in becquerels (Bq, 1 decay per second) or curies (1 Ci = 3.7 × 10¹⁰ Bq).

For a pure sample, you also need the number of atoms. If you know the mass and molar mass, use Avogadro’s number. If you have a solution, you need the concentration and volume. If you have a gas, use the ideal gas law to find moles.

Common Problems and Pitfalls

  • Unit mix-ups: Activity in curies must be converted to Bq (1 Ci = 3.7 × 10¹⁰ Bq). Mass in milligrams must be converted to grams. Time units: half-life often comes out in seconds; convert to years or days as needed.
  • Impure samples: If the sample contains other radioactive isotopes, the measured activity is the sum of all decays. You need to know the fraction of the isotope of interest.
  • Daughter products: If the daughter is also radioactive and present, it adds to the count rate. For a freshly purified sample, this may be negligible initially.
  • Detector efficiency: A detector does not count every decay. If efficiency is 10%, the true activity is 10× the measured count rate.
  • Background radiation: Always subtract the background count rate measured without the sample.

Using Half-Life to Find Decay Rate

The relationship works both ways. If you know the half-life, you can find the decay constant λ = ln(2)/t₁/₂, and then the activity A = λN. For example, carbon-14 has a half-life of 5730 years (1.808 × 10¹¹ s). For 1 gram of carbon in a living organism, the number of ¹⁴C atoms is about 6 × 10¹⁰, giving an activity of about 0.23 Bq (0.23 decays per second). This is why radiocarbon dating requires sensitive detectors and careful background subtraction.

Real-World Example: Cobalt-60

Cobalt-60 is a common medical and industrial gamma source. Its half-life is 5.27 years (1.662 × 10⁸ s). Suppose you have a 1 μg sample (1 × 10⁻⁶ g) of pure ⁶⁰Co (molar mass 59.934 g/mol).

  • N = (1 × 10⁻⁶ / 59.934) × 6.022 × 10²³ = 1.005 × 10¹⁶ atoms.
  • λ = ln(2) / 1.662 × 10⁸ = 4.17 × 10⁻⁹ s⁻¹.
  • A = λN = 4.17 × 10⁻⁹ × 1.005 × 10¹⁶ = 4.19 × 10⁷ Bq (41.9 MBq).

So 1 μg of ⁶⁰Co has an activity of about 42 million decays per second. This illustrates how a tiny mass can have a huge activity when the half-life is short.

Frequently Asked Questions

Q: What is the difference between decay rate and decay constant?
Decay rate (activity) is the number of decays per second (Bq) in a specific sample. Decay constant λ is a probability per unit time for one atom to decay – it is a property of the isotope, independent of sample size. Activity = λ × N.

Q: Can I find half-life from just the decay rate without knowing the mass?
No. The decay rate alone does not tell you how many atoms are present. You need the number of radioactive atoms (from mass, volume, or count) to get λ. If you know the half-life, you can find the number of atoms from the activity, but not the other way around.

Q: Why is the half-life formula t₁/₂ = ln(2)/λ?
It comes from the integrated first-order decay law N(t) = N₀e⁻λᵗ. Setting N(t₁/₂) = N₀/2 gives 1/2 = e⁻λᵗ₁/₂, so ln(1/2) = -λt₁/₂, hence t₁/₂ = ln(2)/λ.

Q: What if my sample has more than one radioactive isotope?
Then the total activity is the sum of each isotope’s activity. You cannot get a single half-life from the total decay rate unless you separate the isotopes or use decay curve analysis (fitting the count rate over time to a sum of exponentials).

Q: How do I convert activity from curies to becquerels?
1 curie (Ci) is exactly 3.7 × 10¹⁰ becquerels. Multiply the value in Ci by 3.7 × 10¹⁰ to get Bq. For example, 1 mCi = 3.7 × 10⁷ Bq.

Limitations and Practical Notes

This method assumes a pure, single-isotope sample with a known mass. In practice, radioactive samples are rarely pure – they may contain stable isotopes of the same element, other radioactive isotopes, or decay products. The activity measurement must be corrected for detector efficiency, geometry, and self-absorption. For very long half-lives (e.g., uranium-238, t₁/₂ ≈ 4.5 × 10⁹ years), the activity is so low that a small sample may emit only a few decays per minute, making accurate measurement difficult. Conversely, for very short half-lives, the sample may decay significantly during the measurement, so you need to account for the change in activity over time.

Always follow your lab’s safety protocols, the material safety data sheet (SDS), and your supervisor’s guidance when handling radioactive materials. For study and planning, this calculator provides the arithmetic; real measurements require proper calibration and radiation safety practices.

Related

Formula used
in a | Activity (decay rate) | Bq | 1000 | 0
in m | Mass of sample | g | 1.0 | 0
in mm | Molar mass of isotope | g/mol | 226.025 | 0.001
out th | Half-life | s | (log(2) * (m / mm) * 6.02214076e23) / a | 0
out th_y | Half-life in years | yr | th / (365.25 * 24 * 3600) | 4
out n | Number of atoms | - | (m / mm) * 6.02214076e23 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →