molecalculator

Moles & Molar Mass

Flow Calculator From Cv: Convert Cv to Flow Rate

Calculator No. 01-4680 · Updated · Formula and assumptions shown below

Flow rate 1.000 US gpm
Flow rate
3.785 L/min
= Flow rate × 3.785411784
Valve flow coefficient Cv
1
Set in the form below
Pressure drop
1 psi
Set in the form below
You enter
Valve flow coefficient Cv, Pressure drop (psi), Liquid specific gravity
You get
Flow rate (US gpm), Flow rate (L/min)
Rounding
3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A flow calculator from Cv estimates liquid flow rate from a valve’s flow coefficient, the pressure drop across the valve, and the liquid’s specific gravity. Enter Cv, pressure drop, and specific gravity to get flow in US gallons per minute (gpm), with an optional equivalent in litres per minute (L/min).

Formula

For a liquid under the standard valve-flow convention, Q = Cv × √(ΔP / SG). Here, Q is flow in US gallons per minute (gpm), Cv is the valve flow coefficient, ΔP is the pressure drop across the valve in pounds per square inch (psi), and SG is the liquid’s specific gravity relative to water. The conversion for the second output is L/min = gpm × 3.785411784, since one US gallon is exactly 3.785411784 litres.

Cv is defined as the flow of water, in US gpm, through a valve with a 1 psi pressure drop under the coefficient’s specified reference conditions. The equation scales that reference flow for a different pressure drop and liquid density. It is an estimate for liquid flow, not a universal equation for every fluid or operating regime.

Worked Example

Using the calculator’s default values—Cv = 1, ΔP = 1 psi, and SG = 1:

  • Q = Cv × √(ΔP / SG)
  • Q = 1 × √(1 psi / 1) = 1 US gpm
  • In litres per minute: 1 × 3.785411784 = 3.785411784 L/min, or 3.785 L/min to three decimals.

The calculator displays 1.000 US gpm and 3.785 L/min. The example describes the reference condition embedded in the definition of Cv, not a promise that a real installation will deliver exactly that flow.

Assumptions

  • The liquid is treated as incompressible and its specific gravity is constant at the operating temperature.
  • The pressure input is the pressure drop across the valve, not upstream pressure alone.
  • Cv applies to the valve’s stated opening and configuration; piping and fittings are not included in the calculation.
  • The standard square-root relationship is used without a correction for cavitation, flashing, or other unusual flow conditions.

How to Use a Cv Flow Calculator

  1. Find the applicable Cv. Use the coefficient for the actual valve type, size, trim, and opening. A valve may have a different Cv at each position; the fully open value is not appropriate if the valve is throttled.
  2. Enter pressure drop. Use the difference between inlet and outlet pressure at the valve, expressed in psi. If pressures are supplied in other units, convert them first; for example, 1 bar is approximately 14.5038 psi.
  3. Enter specific gravity. Use the liquid’s density relative to water at a relevant temperature. Water is commonly approximated as SG = 1 for basic calculations. For another liquid, obtain a condition-appropriate value rather than assuming it is 1.
  4. Read the flow estimate. The first result is US gpm. The second is the same flow converted to L/min; it is not an independent calculation.

For instance, a hypothetical valve with Cv = 2, a pressure drop of 4 psi, and a liquid with SG = 1 gives Q = 2 × √(4/1) = 4 gpm. This illustrates the relationship only; a real valve’s published capacity and system conditions must be checked before relying on the number.

What the Result Means—and Does Not Mean

At a fixed Cv and SG, doubling the pressure drop does not double the predicted flow: flow changes with the square root of pressure drop. Increasing pressure drop by a factor of four doubles the calculated flow. At a fixed Cv and pressure drop, a denser liquid (higher SG) reduces the estimate according to the square root of SG.

The result is a valve-flow estimate based on a simplified relationship. It does not establish that a pump can provide the required pressure, that the rest of the pipe system can carry the flow, or that the valve is suitable for the service. Real flow also depends on valve geometry, position, upstream and downstream piping, fluid properties, and operating conditions. For design or control decisions, consult the valve’s technical data and an appropriate engineering method.

Common Errors and Limits

  • Using upstream pressure instead of pressure drop: ΔP is inlet pressure minus outlet pressure across the valve, measured on a consistent basis.
  • Mixing units: This calculator expects psi and reports US gpm. A US gallon differs from an Imperial gallon; do not label the output simply “gallons per minute” where the distinction matters.
  • Using the wrong Cv: Cv can vary substantially with valve opening. A coefficient for a different size, valve design, or position can make the estimate misleading.
  • Ignoring density: SG is dimensionless but must correspond to the liquid and relevant temperature. It is not the liquid’s density in kg/m³.
  • Assuming the model applies to gas: Gas flow is compressible and needs a different calculation with pressure, temperature, and gas-specific properties. This liquid equation should not be used for gases.

The calculator accepts nonnegative pressure drop and Cv, and positive specific gravity. A zero pressure drop or zero Cv produces zero calculated flow, but a value above zero is not proof that the actual system will flow as predicted. The formula also does not model pressure recovery, cavitation, flashing, or choking. Those effects can limit flow and may damage equipment or create hazards, so they require a suitable method and qualified review.

Frequently Asked Questions

What does Cv mean in a flow calculation?
Cv is a valve flow coefficient: under its standard reference definition, it represents water flow in US gpm through the valve at a 1 psi pressure drop. The coefficient depends on the valve and its opening.

How do I calculate flow rate from Cv?
For liquid flow in the standard convention, multiply Cv by the square root of pressure drop in psi divided by specific gravity: Q = Cv × √(ΔP/SG). The answer is in US gpm.

Is Cv the same as Kv?
No. Cv and Kv use different unit conventions. Kv is commonly expressed as cubic metres per hour for water with a pressure drop of 1 bar, while Cv uses US gpm and 1 psi. Use the coefficient and equation that match the data’s convention; do not substitute one value without conversion.

Can I use this calculator for air or gas?
No. The equation here assumes liquid flow and is not valid as a general gas-flow calculation. Gas compressibility makes gas sizing dependent on additional conditions and properties.

Why is my measured flow different from the result?
The actual pressure drop or valve opening may differ from the inputs, or the Cv may not match the installed valve. Piping losses, fluid temperature and density, and effects such as cavitation can also change flow. Check the measurement conditions and valve data before interpreting a discrepancy.

Related

Formula used
in cv | Valve flow coefficient Cv | - | 1 | 0
in dp | Pressure drop | psi | 1 | 0
in sg | Liquid specific gravity | - | 1 | 0.001
out q | Flow rate | US gpm | cv * sqrt(dp / sg) | 3
out ql | Flow rate | L/min | q * 3.785411784 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →