molecalculator

Moles & Molar Mass

Half Life Decay Graph: Reading & Using It

Calculator No. 01-7045 · Updated · Formula and assumptions shown below

Remaining amount 2.5000 g
Fraction remaining
0.2500
= 0.5^(Elapsed time ÷ Half-life (t½))
Percent remaining
25.00 %
= 0.5^(Elapsed time ÷ Half-life (t½)) × 100
Half-life (t½)
5730 s
Set in the form below
You enter
Half-life (t½) (s), Elapsed time (s), Initial amount (g)
You get
Remaining amount (g), Fraction remaining, Percent remaining (%)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A half-life decay graph shows the fraction of a radioactive (or otherwise decaying) sample that remains versus time, dropping by half after each half-life period. You read it by locating a time on the horizontal axis, then tracing up to the curve and across to the vertical axis to find the remaining fraction or percentage. The graph is a smooth exponential curve, not a straight line, and it never quite reaches zero.

Formula

The equation that generates every half-life decay graph is:

N(t) = N₀ × (1/2)^(t / t½)

  • N(t) – amount remaining after time t (grams, becquerels, number of atoms, etc.)
  • N₀ – initial amount at t = 0 (same unit as N(t))
  • t – elapsed time (any time unit, as long as it matches t½)
  • t½ – half-life (same time unit as t)

The exponent t / t½ tells you how many half-lives have passed. If exactly one half-life has elapsed, the exponent is 1 and the fraction is 0.5; after two half-lives, 0.25; after three, 0.125, and so on. The base (1/2) is fixed; only the exponent changes with time.

Worked Example

Using the calculator defaults: carbon-14 has a half-life of 5,730 years. Suppose you start with a 10 g sample and let it decay for 11,460 years (exactly two half-lives).

  1. Calculate the number of half-lives: 11,460 / 5,730 = 2.0
  2. Apply the formula: N = 10 g × (1/2)^2 = 10 g × 0.25 = 2.5 g
  3. Fraction remaining: 0.5^2 = 0.25 (25%)

The calculator returns 2.5 g for the remaining amount, 0.25 for the fraction, and 25.00% for the percent. The graph would show the point (11,460 years, 2.5 g) sitting exactly on the curve, halfway between the 1.25 g value at three half-lives and the 5 g value at one half-life.

Assumptions

  • Decay follows first-order kinetics – the rate is proportional to the amount present.
  • The half-life is constant; it does not change with temperature, pressure, or chemical state (for nuclear decay).
  • No new atoms of the isotope are being added during the decay period.
  • The sample is pure in the isotope being measured, or the measurement distinguishes it from decay products.

How to Read a Half-Life Graph

Most half-life graphs are plotted with time on the x-axis and the remaining amount (or fraction) on the y-axis. The curve starts at the initial amount (y-intercept) and falls steeply at first, then flattens out. This shape is the signature of exponential decay: the absolute loss per unit time gets smaller as the sample shrinks, even though the fraction lost per half-life stays constant at 50%.

To read a value:

  • Find your time on the horizontal axis.
  • Draw a vertical line up to the curve.
  • Draw a horizontal line from that point to the vertical axis.
  • Read the remaining amount or percentage there.

You can also work backwards: if you know the remaining fraction, start on the y-axis, go across to the curve, then down to the time axis to find how much time has passed. This is how carbon dating works – measure the remaining carbon-14 fraction, then read the elapsed time from the curve.

Common Mistakes When Using the Graph

Three errors appear repeatedly when people work with half-life graphs:

  • Reading the y-axis as a linear decrease. The graph is not a straight line; after one half-life you have 50%, not 50% minus a fixed amount. A common trap is assuming after two half-lives you have 0% – you actually have 25%.
  • Mixing time units. If the half-life is in years but your elapsed time is in days, the exponent is wrong by a factor of 365. Convert both to the same unit before calculating.
  • Confusing half-life with the mean lifetime. The mean lifetime (τ) is the average time an atom survives, equal to t½ / ln(2) ≈ 1.443 × t½. The graph decays to 1/e (about 36.8%) at t = τ, not at t = t½.

Another misconception: the graph never reaches zero. Mathematically, (1/2)^(t/t½) is always positive for any finite t. In practice, the amount eventually drops below the detection limit of your instrument, but the curve itself approaches zero asymptotically.

What the Graph Is Used For

Half-life graphs appear in several fields beyond nuclear physics:

  • Radiometric dating – carbon-14 (t½ ≈ 5,730 years) for organic remains, uranium-238 (t½ ≈ 4.5 billion years) for rocks.
  • Nuclear medicine – determining how long a radioactive tracer remains active in the body, using the physical half-life combined with biological clearance.
  • Pharmacokinetics – drug elimination from the bloodstream often follows first-order kinetics, so a plasma concentration versus time graph looks like a half-life decay curve.
  • Environmental science – predicting how long a pollutant or radioactive contaminant persists in soil or water.
  • Archaeology – estimating the age of artifacts from their remaining isotope fraction.

In each case, the graph lets you visually estimate remaining amounts without doing the arithmetic each time, and it makes the exponential nature of the process immediately obvious.

Limits of the Simple Graph

The basic half-life graph assumes a single decay process with a constant half-life. Real situations can be more complex:

  • Decay chains: When a parent isotope decays into a radioactive daughter, the total activity follows a more complicated curve (Bateman equations), not a single exponential.
  • Mixtures: If a sample contains two isotopes with different half-lives, the graph is the sum of two exponentials and appears as a curve that bends differently at early and late times.
  • Measurement uncertainty: Real data points have error bars; the smooth curve is a fit, not a perfect representation of every measurement.
  • Non-first-order processes: Some chemical reactions or biological clearances are zero-order or second-order, producing linear or different curved graphs that should not be read as half-life decay.

For decay chains, the apparent half-life of the mixture changes over time, so a single half-life value is only an approximation. Always check whether the system you are graphing actually follows first-order kinetics before applying the (1/2)^(t/t½) model.

Frequently Asked Questions

Why does the graph curve instead of going straight down?
Because the decay rate is proportional to the amount present. Early on, there are many atoms, so many decay per second. Later, fewer atoms remain, so fewer decay per second. The fraction lost per half-life stays 50%, but the absolute amount lost shrinks, producing the characteristic exponential curve.

Can I use the graph to find the half-life if I only have data points?
Yes. Plot ln(N) versus time; if the decay is first-order, the points fall on a straight line with slope −ln(2)/t½. Alternatively, find the time where the amount drops to half its starting value directly on the graph. For noisy data, fitting an exponential curve to the original plot is more reliable than picking two points.

What is the difference between half-life and decay constant?
The decay constant (λ) is the probability per unit time that a single atom decays. The half-life and decay constant are related by t½ = ln(2)/λ ≈ 0.693/λ. The graph can be written either as N(t) = N₀ e^(−λt) or N(t) = N₀ (1/2)^(t/t½); they are the same curve.

Does temperature or pressure affect the half-life?
For nuclear decay, essentially no – the half-life is a property of the nucleus and is independent of chemical environment, temperature, or pressure. For chemical reactions or drug elimination that follow first-order kinetics, temperature can change the rate constant and therefore the half-life, so the graph would shift.

How many half-lives until the sample is considered gone?
There is no official cutoff. After 10 half-lives, 0.098% remains (about 1/1024). After 20 half-lives, less than one part per million remains. In practice, the sample is “gone” when the remaining amount falls below the detection limit of your measurement method, which depends on the instrument and the initial amount.

Is the graph the same for activity and for mass?
Yes, if the sample is a single isotope. Activity (decays per second) is proportional to the number of atoms, so both activity and mass follow the same exponential decay curve. The y-axis label changes, but the shape and half-life are identical.

Related

Formula used
in half | Half-life (t½) | s | 5730 | 0.001
in t | Elapsed time | s | 11460 | 0
in n0 | Initial amount | g | 10 | 0
out rem | Remaining amount | g | n0 * 0.5^(t / half) | 4
out frac | Fraction remaining | - | 0.5^(t / half) | 4
out pct | Percent remaining | % | 0.5^(t / half) * 100 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →